Scribd
Upload
146 views

Setting IP Address

The document provides instructions for changing the IP address and ID of 58mm and 80mm series network interface printers using the Printer.exe software. It describes connecting the printer to the computer, printing a test page to obtain the current IP address, opening the software to select the printer model and port and enter the new IP address or last 4 digits of the ID number, then clicking settings to implement the changes. It notes to check if the changes were successful by printing another test page.

Uploaded by

Luis Rola
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
146 views

Setting IP Address

The document provides instructions for changing the IP address and ID of 58mm and 80mm series network interface printers using the Printer.exe software. It describes connecting the printer to the computer, printing a test page to obtain the current IP address, opening the software to select the printer model and port and enter the new IP address or last 4 digits of the ID number, then clicking settings to implement the changes. It notes to check if the changes were successful by printing another test page.

Uploaded by

Luis Rola
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

The Printer.

exe software applies to 58mm and 80mm Series Network Interface


printer
Setting IP address
1.C hange
.Change
hanged d the printer IP
To achieve the data communication between computer (or POS host) and network printer, you must
reset the network printer’s IP the same with computer (or POS host) gateway, and the printer's IP, ID
address are unique in the current network, it can be communicate normal. Ex, computer (or POS host)
IP address is 192.168.1.111, the computer (or POS host) gateway is 192.168.1.

Network printer port IP address is original192.168.123.100.


If the computer (or POS host) gateway different with printer gateway or the user wants to change the
printer IP, according to the following steps.

Assume that the current computer user (or POS host) IP address is 192.168.1.111, the printer IP is
192.168.123.100, If you want to print in current network segment 192.168.1, you must change the
printer IP to segment 192.168.1. If you want to change the printer IP to 192.168.1.205，to do as follow

1 Connect the computer (or POS host) with printer

1.1.1 If you connect the printer directly with the computer, connected it by cross lines.
1.1.2 If you connect the computer with printer through the HUB, ROUTER, SWITCH, you can
connect it by direct lines.

1.2 Print test page, get the printer IP address


After the printer is connected, press the feed button and turn on the power. Printer reset test then
remove your hand from the feed button within in 5 second, the printer will print out test list sample for
self test.
When self test is complete, the printer prints out the following.
** Completed **
You can see the printer IP from the self test list.
1.3 Open PRINTER.EXE 1.3 software, change the Printer IP as follow

2009-8-31 VER1.1
The Printer.exe software applies to 58mm and 80mm Series Network Interface
printer

Assume that the current computer user (or POS host) IP address is 192.168.1.111, the printer IP is
192.168.123.100, If you want to print in current network segment 192.168.1, you must change the
printer IP to segment 192.168.1. If you want to change the printer IP to 192.168.1.205，to do as follow

1. Select printer model --- separated it by the width of the print head, for example, POS58 to 58MM
Series Printers
2. Select the printer port - Ethernet port
3. Enter the printer IP address --- get the self test list through the printer self-test.
4. Enter the printer's new IP Address ---- 192.168.1.205
5. Click the Settings button ---- there are 10-20 seconds (when the computer (or POS host) IP and the
printer IP are in different gateway, it will make the computer (or POS host) network disconnect, and will
restoration after change.

2009-8-31 VER1.1
The Printer.exe software applies to 58mm and 80mm Series Network Interface
printer

When pop up any of the above boxes, please turn off the printer power supply, re-print self test page
after 2-3 seconds.
If the printer IP does not change, please check the printer power supply + cable + network connection,
and then repeat steps 1-5.
If the printer IP changed successfully, you can click the link test (as below)

If appears the connection failed dialog box, please


disconnect and then re-start the power of printer, router or switch power supply, computer (or POS
host) network. And once again click the connection test, if the connection failed dialog box appears
again, there reasons are: (self-test list in the printer IP has changed)

① the new IP address of the printer in the current network segment conflict with the other network
connection device IP address.
Solution: Disconnect other network device, change the printer's IP address. Then
connect all equipment, connection test.

2009-8-31 VER1.1
The Printer.exe software applies to 58mm and 80mm Series Network Interface
printer

② the new IP address different with the current printer gateway.


Solution: To test the printer in the current gateway, you must set the printer IP address of gateway
(the first three NO of IP address) same as the current gateway.
③ In rare cases, ID number will appear repeat, disconnect other network connection devices, Stop
and then re-start the computer(or POS host), changing the printer ID.

If there is a connection successfully dialog box . It indicated the printer working


normal in the current gateway.

2. Change ID
In most cases there is no need to change the printer's ID number, (unless the net ID conflicts).
Printer has been assigned an original random ID number, if you want to change the printer's ID,
then you have to input the last four NO of the ID to the "last four MAC address" column, when the
computer (or POS host) and the printer connected, you can change the printer ID by follow steps.

1. Select printer model --- separated it by the width of the print head, for example, POS58 to 58MM
Series printers
2. Select the printer port - Ethernet port
3. Enter the printer IP address --- get the self test list through the printer self-test.
4. Enter a new printer address ----each number between 0-255.
5. Click the ID Settings button ---- there are 10-20 seconds
6. There is a dialog box, please print the self test page to see if the change successful. If failed, please
try again.

2009-8-31 VER1.1

You might also like