PANTERA 1100

Technical Specification
04511-1
2004-06-01

PANTERA
1100
ROCKPILOT

APPLICATION

Pantera 1100 is a hydraulic, self-propelled, self- All panel sections can be opened for easy access to
contained, crawler based surface drilling rig service spots. Powerpack is mounted crosswise at
equipped with a cabin and a rod changer. It drills 89 - the rear of the rig to balance the weight of the boom
140 mm (3 ½" - 5 ½") vertical, inclined or horizontal and the feed.
3
holes with 51 mm and 60 mm (2" and 2 /8") Pantera 1100 has an ergonomic and roomy full
extension rods or 102 - 152 mm (4" - 6") vertical, vision cabin to increase operator's comfort and
inclined or horizontal holes with 76 and 87 mm (3" efficiency. The cabin is certified for F.O.P.S. and
and 3 ½") tubes. Good results in difficult ground R.O.P.S. (Falling Object Protection Structure and
conditions are obtained by using pilot tube drilling, Roll-Over Protection Structure). Windows are safety
where the first rod is replaced by a 76 or 87 mm (3" laminated and the noise level in the cabin is less
or 3 ½") special tube. than 80 dB(A). Optimal visibility to the drilling spot is
Pantera 1100 is equipped with HL 1000, hydraulic achieved by locating the control levers to both sides
top hammer rock drill. With high rotation torque, of the cabin. Drilling functions are proportionally
proper flushing and sophisticated, ergonomic Rock controlled by one joystick on right hand side. Rod
Pilot control system the rig adapts itself easily into changer functions are controlled by another joystick
varying rock conditions. The rig has a telescopic on left-hand side. Cabin exceeds all standards for
boom for fast hole spotting and set up of the feed. operator's working environment.
The cylinder feed for max. 6,1 m (20 ') starter rod for Pantera 1100 is designed for efficient production
single pass drilling together with carousel type rod drilling in medium large to large quarries or open pit
changer with a possibility to use 4,3 m (14 ') rods mines and construction work sites. It suits well also
add productivity of drilling. for wall control and development works. To
The powerpack of Pantera 1100 consists of customize the rig it can be equipped with a variety of
Caterpillar diesel engine and a gearbox, which options to meet special requirements.
divides the power for hydraulic pumps (two variable
displacement pumps) and flushing air compressor.

1/4
 PANTERA 1100
Technical Specification
04511-1
2004-06-01

COVERAGE AREA

Vertical drilling

Vertical
drilling

Horizontal Horizontal
drilling, drilling,
sideways forwards
1m

1m

DIMENSIONS

9655

PANTERA
1100
ROCKPILOT
2630

4010
8025

2010

PANTERA
1100 900
3030

ROCKPILOT
2490

2/4
 PANTERA 1100
Technical Specification
04511-1
2004-06-01

HYDRAULIC ROCK DRILL DUST COLLECTION SYSTEM

Rock drill type HL 1000 Dust collector type DC 1520
3
Drill rod diameters 51, 60 mm Capacity/vacuum 35 m /min at 1200 mm
Drill tube diameters 76, 87 mm vacuum H2O
Operating pressure 90-160 bar Filter elements/material 20 pcs/fiber
2
Percussion rate 33-35 Hz Total filter surface 16 m
Hydraulic motor output 16 kW
Percussion output power 25 Kw
Primary cyclone PE 80
Maximum rotation torque 1 690 Nm
Movable suction head PE 100 S
Shank lubrication Air / oil mist
Weight 290 kg
Flushing Air
Weight 290 / 300 kg
POWERPACK
Engine type Caterpillar C 9
CYLINDER FEED
Number of cylinders 6
Feed type LF 1514 Engine output 224 kW/2 100 rpm
Length of feed 8 025 mm Transmission type Gear box
Rock drill travel 5 580 mm
Hydraulic pumps Variable/gear
(w/o hose reel)
6 100 mm (20') Screw compressor type Enduro 25
Max. length of starter rod 3
(w/o hose reel) Air flushing capacity 13.5 m /min
Max. hole length with 5 480 mm Flushing air pressure up to 10 bar
starter rod (w/o hose reel) Air cleaner 2 pcs, dry type with
Feed/pull out force 36 Kn ejector and safety
Retaining centralizer Pito 15H element
Feed extension travel 1 480 mm Fuel tank 520 l
Feed swing -56/+52° (-20/+94°) Fuel saving system Standard
Feed tilt 11-133° Weight 1 350 kg
Weight 1 360 kg

ROD CHANGER CONTROL SYSTEM

Rod changer type RC 1514 Tamrock Load sensing
Storage capacity (51 mm) 7+1 rods Collaring system Standard
Rod length 3 660, 4 270 mm Antijamming system Hydraulic / electric
Max. hole length (51 mm) 33 m Voltage 24 VDC
Weight without rods 500 kg
OPERATOR’S CABIN
TELESCOPIC BOOM Certificates F.O.P.S. and R.O.P.S.
Boom type ZB 1550 H Noise level in the cabin 80 dB (A)
Boom extension 500 mm Controls Drilling and tramming
Boom lift +50/-17° Heaters Standard
Boom swing (left/right) +2/-27° Pressurization Standard
2
Drilling coverage on flat 1.6 m Seat Multiposition
Collaring height +1.15 /-3.5 m Vibration dampening Standard
Horizontal holes Sideways Safety laminated, tinted,
Windows
with wiper
CARRIER
Track type FL 6 HYDRAULIC SYSTEM
Grouser plate width 310 mm
Filtration rate 12 micron abs.
Ground contact length 2 520 mm
Ground pressure 1.0 kg/cm
2 Cooling capacity up to +50°C ambient
Ground clearance 400 mm Hydraulic oil tank 420 l
Oscillation angles +/- 11° Shank lubrication device SLU 18-1
Tramming force 140 Kn
Tramming speed 1.7/3.5 km/h

3/4
 PANTERA 1100
Technical Specification
04511-1
2004-06-01

STANDARD COMPONENTS THE JAWS FOR DRILL STEELS

1. Rock drill HL 1000, hydraulic Drill steel type Drill steel Recommended
2. Feed LF 1514 diameter hole diameter
3. Rod changer RC 1514
1. Extension rods 51 mm 89 -127 mm
4. Boom ZB 1550 H, telescopic
/ MF rods 2" 3 ½" - 5"
5. Carrier FL 6, oscillating
6. Powerpack Diesel driven, 2. MF-rods 60 mm 102 - 140 mm
3
hydraulic pumps and 2 /8" 4" - 5 ½"
on board compressor 3. Pilot tube 76 mm 89 - 127 mm
7. Hydraulic Load sensing and 3" 3 ½" - 5"
system open center 4. 87 mm
Pilot tube 102 -140 mm
8. Control system THC Pro with Rock Pilot 4" - 5 ½"
3 ½"
9. Operator's Ergo Pro
5. Tubes 76 mm 89 -127 mm
cabin
10. Dust collection DC 1520 H, hydraulic 3” 3 ½" - 5"
system 6. Tubes 87 mm 102 -152 mm
11. Working lights 8 pcs 3 ½" 4" - 6"
12. Gauge set For accumulator pressure
checking
13. Reversing alarm ADJUSTMENT INFORMATION FOR DELIVERY
14. Manuals Service and spare parts Rotation motor
manuals:
2 x paper copy 1. Rotation motor OMT 315 for 76-102 mm, 3"-4"
holes
2 x CD-ROM (Toolman)
2. Rotation motor OMT 500 for 102-152 mm, 4"-6"
15. EU-safety devices
holes

TRANSPORT DIMENSIONS Extension rod lengths

Weight 18 800 kg 1. 3 660 mm 12’

Width 2.52 m 2. 4 270 mm 14’
Height 3.2 m
Total length 10.5 m

SELECTION OF OPTIONS

1. Heating and air conditioning 22. Movable drill steel support

2. Rod greasing 23. Horizontal drilling support
3. P&Q electric angle indicator 24. Towing hook
4. Electric angle indicator TIM 2302 25. Readyness for Power extractor
5. Measuring system TIM 2303 26. Extra manuals
6. Laser based measuring system TIM 2305 27. First service kit for Pantera 1100
7. Power extractor 28. Special tools for HL 1000, field kit
8. Electric filling pump for refuelling ID 880 822 99
9. Remote control box & hydraulic winch (7 tons) 29. Special tools for HL 1000, complete
10. Rollers for rod changer RC 1514 ID 151 737 78
11. Hose reel 30. Central lubrication system
12. Three-bar grouser plates 31. Fast fill connection for fuel and water tanks
13. Guides for grousers 32. Fast fill connection for engine coolant,
14. Flushing control automatics hydraulic oil, engine oil
15. Shut-down of suction for water holes 33. Sanrock Mini H hydraulic bit grinder
16. Water injection system 34. Radio and CD player
17. Water injection system w/o tank 35. Biogradeable hydraulic oil, Shell naturelle HFE
18. Hydraulic ground support HM 75 46 or HFE 68 (synthetic ester)
19. Fuel heater for cabin, hydraulic oil and engine 36. Antifreeze for air lines
20. Kit for alternative steels www.tamrock.com
21. Tube drilling kit SANDVIK TAMROCK reserves the right to change this specification without further notice

SANDVIK TAMROCK OY, P.O.Box 100, FIN-33311 Tampere, FINLAND 4/4

Tel.int. +358 205 44 121, Telefax int. +358 205 44 120