API 510/576

PRESSURE RELIEVING
DEVICES
 INTRODUCTION

The parts of RP-576 covered in the lesson will not be

addressed completely. The effort will be to introduce the topics
of RP-576 and familiarize the student with its content and
study responsibilities. However a question and answer study
exercise has been provided for exam preparation.
 Definitions

3.1.1 car seal: A self-locking seal that when placed in

position and closed, locks and must be cut with wire cutters or
physically broken to be removed. Local jurisdictional
requirements may specify the acceptable method (s) of sealing
or locking block valves.
3.1.2 non-reclosing pressure relief device: A pressure relief
device, which remains open after operation. A manual
resetting means may be provided.
 3 Definitions

3.1.3 pin-actuated device: A non-reclosing pressure relief

device actuated by static pressure and designed to function by
buckling or breaking a pin which holds a piston or a plug in
place. Upon buckling or breaking of the pin, the piston or plug
instantly moves to the full open position.
3.2.1 effective discharge area: A nominal or computed area
used with an effective discharge coefficient to calculate the
minimum required relieving capacity for a pressure relief valve
per the preliminary sizing equations contained in API RP 520.
API Std 526 provides effective discharge areas for arange of
sizes in terms of letter designations, “D’ through “T”.
3.2.2 huddling chamber: An annular pressure chamber
located downstream of the seat of a pressure relief valve for
the purpose of assisting the valve to achieve lift.
 API 510 / API 576

Descriptions of
Pressure Relieving Devices
 Safety Valves
Principle of Operation
A safety valve is a direct spring-loaded pressure relief valve that is
actuated by the static pressure upstream of the valve and characterized
by rapid opening or pop action.
Description
The spring of a safety valve is usually fully exposed, out-side of the valve
bonnet to protect it from degradation due to the temperature of the
relieving medium.
 Safety Valves
Applications
A safety valve is normally used with compressible fluids. Safety valves
are used on steam boiler drums and super-heaters. They may also be
used for general air and steam services in refinery and petrochemical
plants.
Limitations
Safety valves should not be used as follows:
a. In corrosive services (unless isolated from the process by a rupture
disk).
b. Where the discharge must be piped to remote locations or a closed
system.
c. Where the escape of process fluid around blowing valves is not
desirable.
d. In liquid service.
e. As pressure control or bypass valves.
 Relief Valves
Description
A relief valve is a direct spring-loaded pressure relief valve actuated by
the static pressure upstream of the valve. The valve opens normally in
proportion to the pressure increase over the opening pressure.
Principle of Operation
• A relief valve begins to open when the static inlet pressure reaches set
pressure.
• When the static inlet pressure overcomes the spring force, the disk
begins to lift off the seat.
• Relief valves usually reach full lift at either 10% or 25% overpressure,
depending on the type of valve and trim.
• These valves have closed bonnets to prevent the release of corrosive,
toxic, flammable, or expensive fluids.
 Relief Valves

Figure 2 illustrates one type of relief valve. The ASME Code requires that
liquid service relief valves installed after January 1, 1986 have their
capacity certified and stamped on the nameplate.
 Relief Valves
Applications
• Relief valves are normally used for incompressible fluids.
Limitations
Relief valves should not be used as follows:
a. In steam, air, gas, or other vapor services.
b. In services piped to a closed header unless the effects of any constant
or variable back pressure has been accounted for.
c. As pressure control or bypass valves.
 Safety Relief Valve

Description
A safety relief valve is a direct spring-loaded pressure relief valve that
may be used as either a safety or relief valve depending on the
application.
A safety relief valve is normally fully open at 10% over-pressure when
in gas or vapor service. When installed in liquid service, full lift will
be achieved at approximately 10% or 25% overpressure, depending
on trim type.
 Safety Relief Valve with O-ring Seal
Some relief valves are manufactured with resilient O-rings or other
types of soft seats to supplement or replace the conventional
metal-to-metal valve seating surfaces. Figure 3 illustrates one
type of O-ring seat seal as installed in a safety relief valve.
 Conventional Safety Relief Valve
Description
A conventional safety relief valve is a direct spring loaded pressure relief
valve whose operational characteristics (opening pressure, closing
pressure, and relieving capacity) are directly affected by changes in the
back pressure (see Figure 4).
 Conventional Safety Relief Valve
Description
A conventional safety relief valve has a bonnet that encloses the spring and
forms a pressure-tight cavity. The bonnet cavity is vented to the discharge
side of the valve.
Applications
Conventional safety relief valves can be used in refinery and petrochemical
processes that handle flammable, hot, or toxic material. The effect of
temperature and back pressure on the set pressure must be considered when
using conventional safety relief valves.
Limitations
Conventional safety relief valves should not be used in the following
applications:
a. Where any built-up back pressures exceeds the allowable overpressure.
b. Where the CDTP cannot be reduced to account for the effects of variable back
pressure (see API RP 520 Part I).
c. On ASME Section I steam boiler drums or ASME Section I superheaters.
d. As pressure control or bypass valves.
 Balanced Safety Relief Valve
Description
A balanced safety relief valve is a direct spring loaded pressure relief
valve that incorporates a bellows or other means for minimizing the
effect of back pressure on the operational characteristics of the valve.
Whether it is pressure tight on its downstream side depends on its
design. See figures 5 and 6.
Limitations
Balanced safety relief valves should not be used as follows:
a. On ASME Section I steam boiler drums or ASME Section I
superheaters.
b. As pressure control or bypass valves. Balanced type valves require
vented bonnets. A bellows failure allows process media from the
discharge side of the valve to discharge from the bonnet vent. Consider
the nature of the process media (e.g., liquid/vapor, toxicity, and
flammability) when evaluating the bonnet vent disposition.
 Pilot-Operated Pressure Relief Valve

Description
A pilot-operated safety relief valve is a pressure relief valve in which the
major relieving device or main valve is combined with and controlled by
a self actuated auxiliary pressure relief valve (pilot). Depending on the
design, the pilot valve (control unit) and the main valve may be mounted
on either the same connection or separately. The pilot is a spring loaded
valve that operates when its inlet static pressure exceeds its set
pressure. This causes the main valve to open and close according to the
pressure.
 Pilot-Operated Pressure Relief Valve
Description
Process pressure is either vented off by the pilot valve to open the main
valve or applied to the top of the unbalanced piston, diaphragm, or
bellows of the main valve to close it.
 Pilot-Operated Pressure Relief Valve

Applications
Pilot-operated safety relief valves are generally used as follows:
a. Where a large relief area and/or high set pressures are required, since
pilot-operated valves can usually be set to the full rating of the inlet
flange.
b. Where a low differential exists between the normal vessel operating
pressure and the set pressure of the valves.
c. On large low-pressure storage tanks (see API Std 620).
d. Where very short blow down is required
 Pilot-Operated Pressure Relief Valve
Limitations

Pilot-operated safety relief valves are not generally used as follows:

a. In service where fluid is dirty, unless special provisions are taken

(such as filters, sense line purging, etc.)
b. In viscous liquid service, as pilot-operated valve operating
times will increase markedly due to flow of viscous liquids
through relatively small passages within the pilot.
c. With vapors that will polymerize in the valves.
d. In-service where the temperature exceeds the safe limits
for the diaphragms, seals, or O-rings selected.
e. Where chemical compatibility of the lading fluid with the
diaphragms, seals, or O-rings of the valves is questionable.
f. Where corrosion buildup can impede the actuation of the
pilot.
 Rupture Disk Devices
The combination of a rupture disk holder and rupture disk is known as a
rupture disk device. A rupture disk device is a non-reclosing pressure
relief device actuated by the static differential pressure between the inlet
and outlet of the device and designed to function by the bursting of a
rupture disk. A rupture disk device includes a rupture disk and a rupture
disk holder (see Figure 12).
 Rupture Disk Devices

a. A rupture disk is a pressure containing, pressure and temperature

sensitive element of a rupture disk device. Rupture disks may be
designed in several configurations, such as flat, domed (prebulged), or
reverse acting. The rupture disk holder secures the disk in place.

b. nonfragmenting rupture disk is a rupture disk designed and

manufactured to be installed upstream of other piping components, such
as pressure relief valves, and will not impair the function of those
components when the disk ruptures.
c. A rupture disk holder is the structure, which encloses and clamps the
rupture disk in position. Rupture disks normally require a rupture disk
holder although some disks are designed to be installed between
standard flanges without holders.
 Conventional Rupture Disk

A conventional domed rupture disk is a prebulged solid metal disk

designed to burst when it is overpressured on the concave side (see
Figure 13).
 Conventional Rupture Disk

The conventional domed rupture disk of flat-seat or angular-seat design

generally provides a satisfactory service life when operating conditions
are 70% or less of the rated burst pressure of the disk and when limited
pressure cycling and temperature variations are present. If vacuum or
back pressure conditions are present, the disk must be furnished with a
vacuum support to prevent reverse flexing or implosion. Vacuum
supports are designed for continuous service at full vacuum or less.
Special designs are available for back pressure conditions that exceed
15 lbf/in.2 (103 kPa). The conventional domed rupture disk will fragment
upon burst.
 Scored Tension-Loaded Rupture Disk
The scored tension-loaded rupture disk is designed to open along scored
lines (see Figure 14).
 Scored Tension-Loaded Rupture Disk
This type of disk is designed to allow a closer ratio (generally 85%) of
system operating pressure to disk burst pressure. Because the score
lines control the opening pattern, this type of disk is normally
nonfragmenting. The scored tension-loaded rupture disk is manufactured
from thicker material than is used for unscored disks for the same burst
pressure.
 Composite Rupture Disk

A composite rupture disk is a flat or domed metallic or nonmetallic multi-

piece construction disk. The domed composite rupture disk is designed
to burst when it is over pressured on the concave side.
The domed composite rupture disk, available in flat-seat or angular-seat
design, permits typical operation to 80% of the rated burst pressure
under limited pressure cycling and temperature variations.
A flat composite rupture disk is available for the protection of low-
pressure vessels or the isolation of equipment such as exhaust headers
or the outlet sides of pressure relief valves.
Intended as corrosion barriers only, flat composite rupture disks may
typically operate at 50% of the rated burst pressure and are generally
installed between companion flanges rather than specific rupture disk
holders. Rupture disks that act in either direction are available; these
provide positive pressure and vacuum protection.
 Reverse-Acting Rupture Disk

A reverse-acting rupture disk is a domed solid metal disk designed to

burst when it is overpressured on the convex side. Reverse-acting
rupture disks are designed to open by such methods as shear, knife
blades, knife rings, or scored lines (see Figures 15 and 16).
 Reverse-Acting Rupture Disk

The reverse-acting rupture disk is designed to allow a closer ratio of

system operating pressure to burst pressure, up to 90% of the rated
burst pressure. This type of disk is usually nonfragmenting. Because the
reverse-acting rupture disk is actuated by overpressure on the convex
side, thicker disk materials may be used, thereby improving corrosion
resistance, eliminating the need for vacuum support, and providing
longer service life under pressure/vacuum cycling conditions and
temperature fluctuations. Caution should be exercised when inspecting
reverse acting disk utilizing knife blade. If the knife edges become dull,
the knife may not sever the disk. High overpressures may result.
 Graphite Rupture Disk

A graphite rupture disk is manufactured from graphite

impregnated with a binder material and designed to burst by
bending or shearing (see Figure 17).
 Graphite Rupture Disk

Graphite rupture disks are resistant to most acids, alkalis, and organic
solvents. Operation to 70% of the rated burst pressure is generally
permissible. A support may be required for disks that are rated 15 lbf/in.2
(103 kPa) or less; a support also may be required under conditions of
higher back pressure.
Graphite rupture disks fragment upon rupture; provisions for capturing
fragments may be required in certain applications.
 Applications
Rupture disk devices are sometimes used as follows:
a. To protect the upstream side of pressure relief valves against
corrosion by the system fluid.
b. To protect pressure relief valves against plugging or clogging by
viscous fluids or polymerization products.
c. Instead of pressure relief valves if the protected system can tolerate
process interruptions or loss of fluids in case the disk ruptures.
d. Instead of pressure relief valves if extremely fast response is
desirable.
e. As secondary pressure-relieving devices when the difference between
the operating pressure and the rupture pressure is large, depending on
the type of rupture disk selected.
f. To protect the downstream sides of pressure relief valves against
downstream corrosion from headers or against atmospheric corrosion.
g. To minimize process/product leakage and reduce fugitive emissions.
 Applications
A pressure gauge, a try cock, a free vent, or a suitable tell-tale indicator
must be inserted between a rupture disk device installed at the inlet of a
pressure relief valve and the valve (see Figure 18), permitting the
detection of disk rupture or leakage. Since rupture disks are designed to
burst at a specified differential pressure, pressure build up on the down-
stream side of the disk may inhibit the disk's ability to provide
overpressure protection.
 Limitations

For pre-bulged metal rupture disks installed so that pressure acts against
the concave side and for flat metal rupture disks, the operating pressure
of the protected system is usually limited to 65-85% of the disk's
predetermined bursting pressure.

The exact percentage depends on the type of disk used. The service life
of prebulged metal rupture disks under normal operating conditions is
usually one year. They are subject to relatively rapid creep stress failure,
especially at high operating temperatures.

* If not replaced periodically, they may fail without

warning at normal operating pressures.
 Limitations

Higher operating pressures (up to 90% of the disk design bursting

pressure) are possible with the reverse-buckling disk. Less fatigue due to
pulsating and cyclic operating pressure results in a longer service life
than would be expected if the disk were installed with the pressure acting
against the con-cave side. Most reverse-buckling disks should not be
used in liquid full service.
However, if an assured gas pocket rests against the disk and the disk
manufacturer is consulted, liquid service can be considered. With finite
lives, these disks should be replaced periodically. Consult the
manufacturer for recommended replacement times.
 Limitations

Impervious graphite rupture disks offer nearly the same advantages and
disadvantages as the reverse-buckling, metal type. However, with
impervious graphite rupture disks, the piping arrangement may be more
complicated and uneven flange bolt loads or thermal strains in the piping
may crack the disk.

Rupture disks that tend to fragment, such as conventional and graphite

disks, are typically not installed beneath pressure relief valves unless a
means of protecting the pressure relief valve inlet from the fragments is
provided.
 Limitations

CAUTION: When rupture disks are removed for

inspection or when an accompanying relief valve is
serviced, the disks can easily be damaged and can fail
prematurely if reused. Replacement of disks at every
maintenance interval will minimize the chance of
damage and premature failure.
 API 510 / API 576

Causes of Improper
Performance of Pressure
Relieving Devices
 Corrosion

Nearly all types of corrosion are present in refinery and

chemical plant services. Corrosion is a basic cause of many
of the difficulties encountered with pressure relief devices.
Corrosion often appears as: pitted or broken valve parts,
deposits of corrosive residue that interfere with the operation
of the moving parts, or a general deterioration of the material
of the relieving device. Figures 19 through 25 illustrate the
effects of corrosion on relief devices. In addition to internal
parts, exposed studs are vulnerable to environmental
corrosion attack.
Corrosion
 Damaged Seating Surfaces

Because differential loading must be small to prevent leak-age of the

lading fluid, an optical precision on the order of 3 light beads/bands
[0.0000348 in. (0.0008838 mm)] must be maintained in the flatness of
seating surfaces on metal-seated pressure relief valves (see API Std
527). Any imperfection in these seating surfaces will contribute to
improper valve action in service.
 Damaged Seating Surfaces

There are many causes of damaged valve seats in refinery or chemical

plant service, including the following:
a. Corrosion.
b. Foreign particles that get into the valve inlet and pass through the
valve when it opens.,
c. Improper or lengthy piping to the valve inlet or obstructions in the line.
These can cause a valve to chatter.
d. Careless handling during maintenance, such as bumping, dropping,
jarring, or scratching of the valve parts.
e. Leakage past the seating surfaces of a valve after it has been
installed. This leakage contributes to seat damage by causing erosion
(wire drawing) or corrosion of the seating surface.
 Failed Springs
Spring failure occurs in two forms. The first is a weakening of the spring,
which causes a reduction in set pressure and the possibility of premature
opening. The second is a total failure (complete break) of the spring,
which causes uncontrolled valve opening.

Improper Setting and Adjustment

Manuals provided by the valve manufacturer help eliminate improper
setting and adjustment by indicating how to adjust their valves for
temperature, back pressure, and other factors.
 Plugging and Sticking

Valve malfunction may also be due to sticking of the disk or disk holder
in the guide which may be caused by corrosion or galling of the metal or
by foreign particles in the guiding surfaces. Foreign particles in the
guiding surfaces tend to roll metal up, causing severe galling. The use of
a bellows can keep the foreign particles away from the guiding surfaces.

Sticking of valves can also result from machining of valve parts outside
the manufacturer's tolerance limits. Figure 35 shows a disk that is frozen
in the guide as a result of corrosion in sour gas service. If corrosion is
the cause of the sticking, three possible cures are available.
 Misapplication of Materials

Manufacturers can usually supply valve designs and materials that suit
special services. Catalogs show a wide choice of special materials and
accessory options for various chemical and temperature conditions.
Addition of a rupture disk device at the inlet or outlet may help prevent
corrosion.
The hydrogen sulfide (H 2 S) attack on the carbon steel spring in Figure
22 and the chloride attack on the 18Cr-8Ni steel disk in Figure 23
exemplify the results of the misapplication of materials. Where service
experience indicates that a selected valve type or material is not suitable
for a given service condition, an immediate correction that will ensure
dependable operation should be made.
Misapplication of Materials
 Improper Location, History, or
Identification

If not installed at the exact location for which it was Intended a pressure
relief valve might not provide the proper protection. To assist in the
identification of valves and to provide information necessary for correct
repairs and installation, a comprehensive set of specification and
historical records should be maintained and referred to when valves are
removed for inspection and repair. Most pressure relief valves have an
identifying serial or shop number placed on the valve by the
manufacturer or an identifying number tagged, stamped, or otherwise
placed on the valve by the user.

Some users also stamp mating pipe flanges with device numbers.
This identification specifies the location of the valve and, by reference to
the specification record, its limitations and construction (see Section 7).
 Rough Handling
Valves are checked for tightness in the manufacturer's plant before they
are shipped to the user. Valve tightness is sometimes checked by the
user in the maintenance shop before initial use and usually checked after
subsequent cleaning, repairing, or testing. Subsequent rough handling of
the valve, however, can change the set pressure, damage lifting levers,
damage tubing and tubing fittings, damage pilot assemblies or cause
internal or external leakage when the valve is in service.
Rough handling can occur during shipment, maintenance, or
installation.
During Shipment
Because of their operation, most pressure relief valves have a sturdy
appearance that may obscure the fact that they are delicate instruments
with very close tolerances and sensitive dimensions. Accordingly,
commercial carriers sometimes subject them to rough handling. This
may cause a valve to leak excessively in service or during testing.
 Rough Handling

During Maintenance
Careful handling of the valve during all phases of maintenance is
important. Both before and after repairs, rough handling of the
completely assembled valve should be avoided. Before the valves leave
the shop, valve inlets and outlets should be covered.
Rough handling during maintenance includes application of excessive
back pressure, which should not be applied to a bellows valve during a
maintenance-related test.
 Rough Handling

During Installation
Valve inlets and outlets should have been covered before the valves left
the shop. If they were not covered when received for installation,
provisions should be made to ensure that in the future they are covered
before leaving the shop.

Pressure relief valves should be transported in an upright position.

Rough handling of a pressure relief valve by personnel during installation
may cause poor valve performance in service.

Bumping or dropping the valve should be carefully avoided. The valves

shown in Figure 36 were dropped from the bed of a truck after being
repaired. As a result, they leaked once they were installed.
 Improper Differential Between
Operating and Set Pressures

The differential between operating and set pressures provides seat

loading to keep the pressure relief valve tightly closed. Due to a variety
of service conditions and valve designs, only general guidelines can be
given for designing a system.
 Improper Discharge Piping
Test Procedures
When hydrostatic tests of discharge piping are performed, blinds
must be installed. Otherwise, results such as the following might
occur:
a. The disk, spring, and body area on the discharge side of the valve are
fouled.
b. The bellows of a balanced relief valve are damaged by excessive
back pressure.
c. The dome area and/or pilot assembly of a pilot-operated pressure
relief valve are fouled and damaged by the backflow of fluid.
 API 510 / API 576

Inspection and Testing

 Shop Inspection/Overhaul

Periodically, pressure relief devices will be removed, disassembled, and

inspected. These inspections are referred to as "shop
inspection/overhaul" (although some, if not all of the work can be
performed in the field).

Also, while the device is removed, inlet and outlet piping should be
inspected for the presence of internal deposits, and records should be
kept of their condition. If heavy fouling is observed, the piping should be
cleaned. If necessary, piping should be dismantled for inspection and
cleaning.
 Valve Identification
To minimize errors in the testing and handling of pressure relief valves,
each should carry an identifying tag, stencil, plate, or other means to
show its company equipment number.
This number allows ready identification of the device's unit, the
equipment that the device should be installed on, the device's set
pressure, and the date of its last test (see Figure 37 for an example of an
identifying tag).
 Operating Conditions Noted

An operating history of each pressure relief valve since its last inspection
should be obtained and should include pertinent information such as:

a. Information on upsets and their effect on the valve.

b. The extent of any leakage while in service.
c. Any other evidence of malfunctioning.
 Initial Inspection

Many types of deposits or corrosion products in a pressure relief valve

may be loose and may drop out during transportation of the valve to the
shop for inspection, testing, maintenance, and resetting.
As soon as a valve has been removed from the system, a visual
inspection should be made.
Figure 39 shows sulfur deposits in a valve. When fouling is a frequent
problem, it may be prudent to collect samples for testing and to record
deposit locations and appearances. Any obstructions in the valve should
be recorded and removed.
 Inspection of Adjacent Inlet and Outlet
Piping
Inspection of the piping at the pressure relief valve will often indicate the
condition of the process piping whose interior is not visible. Piping
should be checked for corrosion, indications of thinning, and deposits
that could interfere with valve operation. The character of the deposits
may indicate the cause of any leakage from the valve in a closed
system.
 Transportation of Valves to Shop
After a pressure relief valve is removed from its installation, it should be
transported to the shop for inspection, testing, maintenance, and
resetting. Before moving the valve, flange faces on the valve (and
flanges on the piping) should be protected so that gasket faces are not
damaged. The valves should be transported in the upright position.

Determining "As Received” Pop Pressure

Check that the seals are intact on the pressure set screw cover and
blowdown ring screw cover. Before the valve is dismantled, the pop
pressure of the valve when removed from service should be obtained.
Generally the pressure relief valve is mounted on the test block, and the
inlet pressure is slowly increased. The pressure at which the valve
relieves is recorded as the "as received" pop pressure. Typically, the inlet
pressure is not increased beyond 150% of the pressure relief valve set
pressure.
Determining "As Received” Pop Pressure
If initially the valve opens at the cold differential test pressure, CDTP, no
further testing to determine the "as received" pop pressure is needed. If
the initial pop is at a pressure higher than the CDTP, the valve should be
tested a second time. If it then pops near the CDTP, the valve probably
did not originally pop at the CDTP because of deposits.

Pressure relief valves that do not pop at inlet pressures of up to 150% of

CDTP should be considered as stuck shut.
 Visual Inspection
During inspection the points that should be checked include:
a. The flanges, for evidence of pitting, roughening, or decreases in the
width of seating surfaces.
b. The springs, for evidence of corrosion or cracking and for the correct
pressure range at the valve's operating pressure and temperature.
c. If the valve is of the bellows type, the bellows for evidence of
corrosion, cracking or deformation.
d. The positions of the set screws and openings in the bonnet.
e. The inlet and outlet nozzles, for evidence of deposits of foreign
material or corrosion.
f. The external surfaces, for any indication of a corrosive atmosphere or
of mechanical damage.
g. The body wall thickness.
h. Valve components and materials, for a match with the information on
the identification tag and specification card.
i. The pilots and associated parts
 Visual Inspection

CAUTION: When unusual corrosion, deposits, or conditions are

noted in the pressure relief valve, an inspector should assist in the
inspection.

CAUTION: If the pressure relief valve is from equipment handling

hazardous materials, caution should be exercised during the
inspection.
 Setting of Valve Set Pressure
Normally, the deviation of the pop pressure from the set pressure should
not exceed ±2 lbf/in.2 (±13.8 kPa) for pressures less than or equal to 70
lbf/in.2 (483.0 kPa) or ±3% for pressures greater than 70 lbf/in.2 (483.0
kPa)
Follow the valve manufacturer’s recommended testing procedure when
the pressure relief valve is tested with water. Typically, the pressure will
be raised slowly to the required setting. The discharge should be
observed for evidence of leakage, or the test gauge should be observed
for a momentary drop in pressure. A small continuous stream of water
from the valve discharge usually indicates attainment of the CDTP.
 Checking Valve for Tightness

Once the valve is set to pop at its CDTP, it should be checked for
leakage. On the test block, it can be tested for seat tightness by
increasing the pressure on the valve to 90% of the CDTP and observing
the discharge side of the valve for evidence of leakage. Methods of
determining leakage are covered in Appendix B.2 and Figure 40.

Where applicable, the bonnet, bellows, gasketed joints and auxiliary

piping/tubing should be inspected for leakage.
Checking Valve for Tightness

Figure 40 API 576

 Completion of Necessary Records

All necessary records should be completed before a valve is placed back

into service. By helping to determine when to replace the components of
the valve and when to retire it, the records are critical to its effective
future use. They form the historical record of the conditions and services
under which the valve operated. Retention of maintenance and test
records may be required by governmental regulations.

See Appendix A for example forms. For an explanation of nameplate

terms required by repair work, see API Std 526.