The Long Life High Temperature Grease

for the Packaging Industry

®
Turmotemp LP 2502

High temperature, high bearing load and an aggressive environ- Improved Machine Reliability with Automatic
ment require extraordinary lubricants. Turmotemp LP 2502 enables Lubrication of High Temperature Bearings
reliable bearing operation in complex corrugated board manufac-
turing machines. Due to the homogenous structure of the Turmotemp LP 2502, automatic
lubrication becomes available to high temperature bearings within the
Special High-Temperature Grease corrugated board manufacturing environment. Competitors greases with
Teflon particle thickeners, have the tendency to separate the oil from the
Turmotemp LP 2502 is the first grease, combining the superior thickener under pressure and consequently block any valves or
long-term and high-temperature properties of perflourinated polyether progressive distribution blocks of central lubrication systems.
(PFPE) with the excellent thickening capability and properties of a LUBCON’s smart automatic lubricator EasyMatic, in combination with
special high temperature resistant Lithium soap. Due to this unique advanced technology high temperature lubricants, contribute signifi-
combination of thickener and high temperature resistant base oil, cantly to increased reliability and safety within the packaging industry.
Turmotemp LP 2502 has superior anti-corrosion resistance and
outstanding wear protection. As a consequence, up to three times
longer bearing service life has been experienced in practice. The lubrication positions of the hot section
corrugator bearings are often difficult to reach
¡ efficient protection against wear, fretting and corrosion and can in many cases, only be lubricated by
interrupting the manufacturing process. With
¡ enables three times longer bearing service life automatic lubrication, the actual frequency of
¡ vibration and noise reduction lubricant refreshment as well as the accuracy
¡ lower friction torque, energy saving of the lubricant replacement within the
¡ no hardening effects bearings, is much higher. The bearings
operate in significantly cleaner and better
¡ no oil separation effects
lubricated condition.
¡ no acidic vapors in case of over temperature
¡ no hazardous ingredients The continuous lubrication thus contributes to improved machine
¡ miscible with any PTFE/PFPE lubricant reliability, reduced downtime, cost saving and productivity.
¡ no special cleaning agents required, bearings can be cleaned with
standard shop solvents, cost saving
¡ is compatible with elastomers, nonferrous or ferrous metals. Technical Data Turmotemp LP 2502
Color light beige
Applications
Structure homogeneous / creamy
Turmotemp LP 2502 is a long-term lubricant for any kind of rolling
bearings operating at high temperatures and high loads. Compared with Density at 68 °F (20 °C) approx. 1,7 g/cm³
other lubricants, better wear protection can be expected for all ball
bearings and in particular line contact bearings, e.g. spherical roller Service temperature range -22 °F to 500 °F (-30 °C to 260 °C)
bearings, cylindrical roller bearings, taper roller bearings etc..
Consistency grade 2
Turmotemp LP 2502 operates up to a bearing temperature of 500 °F and
thus gives optimum protection for bearings of corrugated board machinery Mechanical load (Four-Ball Test) > 5500 N
(cardboard production, pre-heater and pressure rolls bearings).
Speed factor 500 000 n x dm
It is also used for chain
return wheels and return Corrosion protection 0/0
roller bearings subject to
high temperatures, loaded Base oil perflourinated polyether
rollers in film stretching
machines and textile Thickener Lithium special soap
stenters, low-speed
high-temperature electric Viscosity at 40 °C (104 °F) 250 cSt (mm²/s)
motors, high temperature
fan bearings and many Viscosity at 100 °C (212 °F) 26 cSt (mm²/s)
other applications. Corrugated board machine from FARO International GmbH
 ®
Turmotemp LP 2502
The Long Life High Temperature Grease
for the Packaging Industry

Modern Lubricants for Best Machine

Performance and Reliability
LUBCON’s lubricants are used widely in the corrugated board industry Advanced calculation methods have been developed to help the
and have significantly contributed to long-term reliability and superior customer select the right lubricant in terms of optimum operating
performance. The full range of lubricants is available from a single condition and grease service life. Training seminars, for better
source, together with the most advanced lubrication systems. understanding of bearing operation and lubrication technology, have
been composed and made available for maintenance personnel,
Turmocut SR 15 is a lubri- engineering staff, designers etc..
cating oil based on high-
purity hydro-carbons for the Automatic lubrication devices are available to extend maintenance
Slitter and Scorer from BHS. free operation. To enable better handling and disassembly of bearings,
It is a combination of base oil fittings and any clamping devices during overhaul, assembly pastes
and additives, which can be have been developed and are available in a various range of packag-
used in the food processing ing as well as aerosols.
industry. It has very good
surface wetting properties, ü Grease service life program
shows excellent lubrication ü Lubrication quantity and interval calculation tool
characteristics, dissolves ü Training seminars
starch and thus keeps the ü Assembly pastes
knifes cleaner and sharper ü Cleaning spray LC 500
and provides additional life ü Automatic lubrication devices from a single point lubricator to
with less maintenance. The central lubrication systems with a maximum of 44 lubrication
lubricant is InS/H1 food grade lines.
approved.
LUBCON Lubrication Systems
Turmogearoil 460 OM is a solid-free, high performance gear oil, TLB 2000 - The automatic pin chain lubricator supplies
containing a newly developed additive combination. For long-term accurate lubricant quantities with precise timing to con-
lubrication under conditions, exceeding the capability of conventional veyor chains. Optimum lubrication with LUBCON
EP lubricants or oils with solid lubricants. LUBCON's active anti-wear chain oils and accurate minimum oil quantities extends
additive combination was been developed for optimum protection the chain life up to factor 3.
under severe load and a wide operating temperature range. For food
grade packaging applications, the NSF/H1 approved Turmosynth VG
460 can be utilized. EasyMatic - Automatic lubricator for oils and greases
up to 22 lubricating points (44 points with two pump el-
ements). EasyMatic has been developed for auto-
Turmopast NBI 2 white is a light-colored lubrication and assembly paste, matic long term lubrication of machines in industrial
containing solid lubricants to reduce fretting corrosion as well as friction environment.
at low speeds or high vibration levels. Well balanced anti-wear and
anti-corrosion additives provide excellent long-term protection for any
press fits such as bearing-shaft or bearing-housing assemblies. Bearing MicroMax 120 - Single point lubricator for automatic
assemblies, guide bushing, threads, fittings and many others are easier lubrication up to a maximum of 3 years. Can be used
to disassemble due to excellent protection against fretting corrosion. for any individual bearing, ball screws, gears, etc.
with a large variety of long life greases.

Turmofluid ED 13 is a synthetic lubricant for multipurpose use with

excellent spreading capabilities on metallic surfaces. The water DuoMax 160 - Double point lubricator for maintenance-
displacement behavior and the high metal affinity of Turmofluid ED 13 free operation of e.g. electric motors up to a maximum
will ensure an optimum lubrication and an excellent corrosion of 3 years. Can also be used for fan shaft bearings and
protection. Turmofluid ED 13 is used for the lubrication of machines as many others with a large variety of long life greases.
well as machine parts , chains, guide elements and many others.
All LUBCON products are OEM approved and available from stock in
a large variety of packaging solutions, from 50 ml tubes, Manual and pneumatic grease pumps - A large variety
400 ml (14 oz) cartridge up to 200l (55 gal) drums. of manual and pneumatic grease guns and pumps
with respective equipment are available to handle the
lubricants in an industrial environment.

LUBRICANT CONSULT GMBH

Release date: 2017-09-01

Lubricants § Lubrication Technology

Gutenbergstraße 11-13 § 63477 Maintal § GERMANY § P.O. Box 20 02 40 § 63469 Maintal § GERMANY
Tel.: +49 6109 7650-0 § Fax: +49 6109 7650-51 § Email: webmaster@lubcon.com § www.lubcon.com
This brochure contains only general product information. For specific information please refer to our technical data and safety data sheets. The content represents the actual state of development and
knowledge of LUBRICANT CONSULT GmbH that can be subject to change without notification. The products mentioned fully comply with the specifications defined by our company, but due to the multitude of
different applications and influencing factors, we cannot guarantee suitability for the individual application. To determine the suitability of a lubricant we, therefore, recommend contacting an application
engineer and, if necessary, performing individual field tests. Any further liability by LUBRICANT CONSULT GmbH is expressively excluded.