Introduction To Mass Transfer - Part 1

Introduction to Mass
Transfer
Introduction
 Three fundamental transfer processes:
i) Momentum transfer
ii) Heat transfer
iii) Mass transfer
 Mass transfer may occur in a gas
mixture, a liquid solution or solid.
 Mass transfer occurs whenever there is
a gradient in the concentration of a
species.
 The basic mechanisms are the same
whether the phase is a gas, liquid, or
solid.
Definition of Concentration
i) Number of molecules of each species
present per unit volume
(molecules/m3)
ii) Molar concentration of species i =
Number of moles of i per unit volume
(kmol/m3)
iii) Mass concentration = Mass of i per
unit volume (kg/m3)
Diffusion phenomena
 Fick’s law: linear relation between the rate of
diffusion of chemical species and the
concentration gradient of that species.
 Thermal diffusion: Diffusion due to a
temperature gradient. Usually negligible unless
the temperature gradient is very large.
 Pressure diffusion: Diffusion due to a pressure
gradient. Usually negligible unless the pressure
gradient is very large.
 Forced diffusion: Diffusion due to
external force field acting on a
molecule. Forced diffusion occurs when
an electrical field is imposed on an
electrolyte ( for example, in charging an
automobile battery)
 Knudsen diffusion: Diffusion
phenomena occur in porous solids.
 Whenever there is concentration difference in a medium,
nature tends to equalize
things by forcing a flow
from the high to the low
concentration region.
Before After
 The molecular transport process of mass is characterized

by the general equation:
Rate of transfer process = driving force

resistance
Example of Mass Transfer Processes
 Consider a tank that is divided into two equal
parts by a partition.
 Initially, the left half of the tank contains
nitrogen N2 gas while the right half contains
O2 at the same temperature and pressure.
 When the partition is removed the N2
molecules will start diffusing into the air while
the O2 molecules diffuse into the N2.
 If we wait long enough, we will have a
homogeneous mixture of N2 and O2 in the
tank.
 Liquid in open pail of water evaporates
into air because of the difference in
concentration of water vapor at the
water surface and the surrounding air.
 A drop of blue liquid dye is added to a
cup of water. The dye molecules will
diffuse slowly by molecular diffusion to
all parts of the water.
Molecular Diffusion Equation
 Fick’s Law dc A
J *
AZ   DAB
dz
J *A is the molar flux of component A in the
z direction in kg mol A/s.m2.
D AB is the molecular diffusivity of the

molecule A in B in m2/s
c A is the concentration of A in kg mol/m3.
z is the distance of diffusion in m
Fick’s Law of Diffusion
 Molecular diffusion or molecular transport can be defined as the
transfer or movement of individual molecules through a fluid by
mean of the random, individual movements of the molecules.
(2) A
B
B B
B B B
B
B B B
(1) A
Figure 3: Schematic diagram of molecular diffusion process
 If there are greater number of A molecules near point (1) than at
(2), then since molecules diffuse randomly in both direction, more A
molecules will diffuse from (1) to (2) than from (2) to (1).
 The net diffusion of A is from high to low concentration regions.
 The two modes of mass transfer:
- Molecular diffusion
- Convective mass transfer
Molecular diffusion
The diffusion of molecules when the whole
bulk fluid is not moving but stationary.
Diffusion of molecules is due to a
concentration gradient.
The general Fick’s Law Equation for binary mixture of A and B
dx A
*
J AZ  cD AB
dz
c = total concentration of A and B [kgmol (A + B)/m3]
xA= mole fraction of A in the mixture of A and B
Example
A mixture of He and N2 gas is contained
in a pipe at 298 K and 1 atm total
pressure which is constant throughout.
At one end of the pipe at point 1 the
partial pressure pA1 of He is 0.6 atm and
at the other end 0.2 m pA2 = 0.2 atm.
Calculate the flux of He at steady state
if DAB of the He-N2 mixture is 0.687 x
10-4 m2/s.
Solution
 Since a total pressure P is constant, the c is constant, where c is
as follows for a gas according to the perfect gas law:
 Where n is kg mol A plus B, V is volume in m3, T is temperature

in K, R is 8314.3 m3.Pa/kg mol.K or R is 82.057 x 10-3 cm3.
atm/g. mol. K, and c is kg mol A plus B/m3.
 For steady state the flux J*Az in Eq.(6.1-3) is constant. Also DAB
for gas is constant. Rearranging Eq. (6.1-3) and integrating.
(6.1-11)
 Also, from the perfect gas law, pAV=nART, and
 Substituting Eq. (6.1-12) into (6.1-11),
(6.1-13)
 This is the final equation to use, which is in a form eqsily used

for gases. Partial pressures are pA1 = 0.6 atm = 0.6 x 1.01325 x
105 = 6.04 x 104 Pa and pA2 = 0.2 atm = 0.2 x 1.01325 x 105 =
2.027 x 104 Pa. Then, using SI units,
 If pressures in atm are used with SI unit,
 Other driving forces (besides concentration

differences) for diffusion also occur because
of temperature, pressure, electrical potential,
and other gradients.
Convection Mass Transfer
 When a fluid flowing outside a solid surface in forced convection
motion, rate of convective mass transfer is given by:
N A  k c (c L1  c Li )
kc - mass transfer coefficient (m/s)
cL1 - bulk fluid conc.
cLi - conc of fluid near the solid surface
 Kc depend on:
1. system geometry
2. Fluid properties
3. Flow velocity
Principles of Mass
Transfer
Molecular Diffusion in Gases
CONTENTS
Mass Transfer
Molecular Diffusion Convective Mass Transfer
Gases Liquid Solid

Molecular Diffusion in Gases
 Equimolar Counterdiffussion in Gases
 For a binary gas mixture of A and B, the
diffusivity coefficient DAB=DBA
Example 6.2-1
Ammonia gas (A) is diffusing through a
uniform tube 0.10 m long containing N2
gas (B) at 1.0132 x 105 Pa pressure and
298 K. The diagram is similar to Fig. 6.2-
1. At point 1, pA1 = 1.013 x 104 Pa and
at point 2, pA2 = 0.507 x 104 Pa. The
diffusivity DAB = 0.230 x 10-4 m2/s.
(a) Calculate the flux J*A at steady state
(b) Repeat for J*B
Solution
 Equation (6.1-13) can be used, where P = 1.0132 x 105 Pa, z2-z1
= 0.10 m, and T = 298 K. Substituting into Eq. (6.1-13) for part
(a),
 Rewriting Eq. (6.1-13) for component B for part (b) and noting
that pB1 = P – pA1 = 1.01325 x 105 – 1.013 x 104 = 9.119 x 104
Pa and pB2 = P – pA2 = 1.01325 x 105 – 0.507 x 104 = 9.625 x
104 Pa.
 The negative for J*B means the flux goes from point 2 to point
1.
Diffusion of Gases A and
B Plus Convection
For equimolar counterdiffussion, NA=-NB ,
then NA=J*A=-NB=-J*B
Example 6.2-2
Water in the bottom of a narrow metal tube is held at a
constant temperature of 293 K. The total pressure of air
(assumed dry) is 1.01325 x 105 Pa (1.0 atm) and the
temperature is 293 K (20 °C). Water evaporates and
diffuses through the air in the tube, and the diffusion
path z2-z1 is 0.1524 m (0.5 ft) long. The diagram is
similar to Fig. 6.2-2a. Calculate the rate of evaporation
at steady state in lb mol/h.ft2 and kg mol/s.m2. The
diffusivity of water vapor at 293 K and 1 am pressure is
0.250 x 10-4 m2/s. Assume that the system is
isothermal. Use SI and English units.
Solution
 The diffusivity is converted to ft2/h by using the conversion
factor:
 From Appendix A.2 the vapor pressure of water at 20 °C is

17.54 mm, or pA1 = 17.54/760 = 0.0231 atm = 0.0231(1.01325
x 105) = 2.341 x 103 Pa, pA2 = 0 (pure air). Since the
temperature is 20 °C (68 °F), T = 460 + 68 °R = 293 K. From
Appendix A.1, R = 0.730 ft3.atm/lb mol.°R . To calculate the
value of pBM from Eq. (6.2-21)
 Since pB1 is close to pB2, the linear mean (pB1+pB2)/2
could be used and would be very close to pBM.
 Substituting into Eq. (6.2-22) with z2-z1 = 0.5 ft
(0.1524m),
Example 6.2-4
A sphere of naphthalene having a radius of 2.0
mm is suspended in a large volume of still air at
318 K and 1.101325 x 105 Pa (1 atm). The
diffusivity of the naphthalene at 318 K is 6.92 x
10-6 m2/s.
Calculate the rate of evaporation of
naphthalene from the surface.
Solution
 The flow diagram is similar to Fig. 6.2-3a. DAB = 6.92 x 10-6
m2/s, pA1 = (0.555/760)(1.01325 x 105) = 74.0 Pa, pA2 = 0, r1 =
2/1000 m, R = 8314 m3.Pa/kg mol.K, pB1 = P-pA1 = 1.01325 x
105 – 74.0 = 1.01251 x 105 Pa, pB2 = 1.01325 x 105 – 0. since
the values of pB1 and pB2 are close to each other,
 Substituting into Eq. (6.2-32),

Introduction To Mass Transfer - Part 1

Uploaded by

Copyright:

Available Formats

Introduction To Mass Transfer - Part 1

Uploaded by

Copyright:

Available Formats

Introduction to Mass

 The molecular transport process of mass is characterized

Rate of transfer process = driving force

D AB is the molecular diffusivity of the

 Where n is kg mol A plus B, V is volume in m3, T is temperature

 Substituting Eq. (6.1-12) into (6.1-11),

 This is the final equation to use, which is in a form eqsily used

 Other driving forces (besides concentration

Molecular Diffusion Convective Mass Transfer

Gases Liquid Solid

 From Appendix A.2 the vapor pressure of water at 20 °C is

 Substituting into Eq. (6.2-32),

You might also like