Harman/kardon: Service Manual

harman/kardon AVR 355/230 Service Manual
harman/kardon Service Manual
AVR 355/230
7 x 65W 7.1 CHANNEL A/V RECEIVER
CONTENTS
ESD WARNING 2 EXPLODED VIEW AND PARTS 8

BASIC SPECIFICATIONS 3 ELECTRICAL PARTS LIST 9
TROUBLESHOOTING GUIDE 4 SEMICONDUCTOR PINOUTS 56
PROCESSOR RESET 4 PCB DRAWINGS 101
REMOTE RESET 5 BLOCK DIAGRAM 109
PACKAGE LIST AND PARTS 6 WIRING DIAGRAM 110
DISASSEMBLY 7 AMP BIAS ADJUSTMENT 111
SCHEMATIC DIAGRAMS 112
Released EU2008 harman/kardon, Inc. Rev 0, 09/2008

250 Crossways Park Dr.
Woodbury, New York, 11797
Page 1 of 125
Downloaded from www.Manualslib.com manuals search engine
Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called
Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field effect transistors and
semiconductor "chip" components.
The following techniques should be used to help reduce the incidence of component damage caused by static electricity.
1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any electrostatic charge on
your body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging wrist strap device,
which should be removed for potential shock reasons prior to applying power to the unit under test.
2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as aluminum foil, to
prevent electrostatic charge build-up or exposure of the assembly.
3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.
4. Use only an anti-static solder removal device. Some solder removal devices not classified as "anti-static" can generate electrical charges
sufficient to damage ES devices.
5. Do not use freon-propelled chemicals. These can generate electrical change sufficient to damage ES devices.
6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most replacement
ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or comparable conductive material.)
7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material to the
chassis or circuit assembly into which the device will be installed.
CAUTION : Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.
8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the brushing together
or your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity sufficient to damage an ES devices.
Each precaution in this manual should be followed during servicing.
Components identified with the IEC symbol in the parts list are special significance to safety. When replacing a component identified with
, use only the replacement parts designated, or parts with the same ratings or resistance, wattage, or voltage that are designated in the
parts list in this manual. Leakage-current or resistance measurements must be made to determine that exposed parts are acceptably
insulated from the supply circuit before retuming the product to the customer.
Page 2 of 125
0029CSK - AVR355+255 ENG v11.qxp:33906_AVR350_Eng 19/05/08 11:23 Side 51 (Sort/Black plade)

Technical Specifications
Audio Section FM Tuner Section

Stereo Mode Frequency Range 87.5–108MHz
Continuous Average Power (FTC): Usable Sensitivity IHF 1.3 µV/13.2dBf
70 Watts per channel, 20Hz - 20 kHz Signal-to-Noise Ratio Mono/Stereo: 70/68dB (DIN)
@ < 0.07% THD, both channels driven into 8 ohms Distortion Mono/Stereo: 0.2/0.3%
7 Channel Surround Modes Stereo Separation 40dB @ 1kHz
Power Per Individual Channel, with all channels driven Selectivity ±400kHz: 70dB
Image Rejection 80dB
Front L&R channels:
IF Rejection 90dB
65 Watts per channel
@ < 0.07% THD, 20Hz–20kHz into 8 ohms
AM Tuner Section
Center channel: Frequency Range 522–1620kHz
65 Watts Signal-to-Noise Ratio 45dB
@ < 0.07% THD, 20Hz–20kHz into 8 ohms Usable Sensitivity Loop: 500µV
Surround (L & R Side, Back) channels: Distortion 1kHz, 50% Mod: 0.8%
65 Watts per channel Selectivity ±10kHz: 30dB
@ < 0.07% THD, 20Hz–20kHz into 8 ohms
Input Sensitivity/Impedance Video Section
Linear (High Level) 200mV/47kohms Video Format PAL/NTSC
Input Level/Impedance 1Vp-p/75 ohms
Signal-to-Noise Ratio (IHF-A) 100dB
Output Level/Impedance 1Vp-p/75 ohms
Surround System Adjacent Channel Separation Video Frequency Response
Analog Decoding 40dB (Composite and S-Video) 10Hz–8MHz (-3dB)
(Pro Logic, etc.) Video Frequency
Dolby Digital (AC-3) 55dB Response (Component) 10Hz–100MHz (-3dB)
DTS 55dB
Frequency Response General

@ 1W (+0dB, –3dB) 10Hz–130kHz Power Requirement AC 220–240V/50Hz
High Instantaneous Power Consumption AVR 355: Standby < 3W,
Current Capability (HCC) ±35 Amps 890W maximum
Transient Intermodulation (7 channels driven)

Distortion (TIM) Unmeasurable Dimensions (Max)
Rise Time 16 µsec Widt 440mm
Height 165mm
Slew Rate 40V/µsec**
Depth 382mm
Weight net 14,4 kg
Depth measurement includes knobs, buttons and terminal connections.

Height measurement includes feet and chassis.
All features and specifications are subject to change without notice.
Harman Kardon, The Bridge and Logic 7 are registered trademarks of Page 3 of 125
Harman International Industries, Incorporated.
is a trademark of Harman International Industries, Inc.
*Manufactured under license from Dolby Laboratories.
"Dolby True HD", "Dolby Digital Plus", “Dolby,” “Pro Logic” and the Double-D symbol are
trademarks of Dolby Laboratories.
"DTS-HD Master Audio", "DTS-HD", "DTS","DTS ES","Neo:6"and"96/24" are
Downloaded from www.Manualslib.com manuals of
trademarks search engine
DTS,Inc.
Troubleshooting Guide
SYMPTOM CAUSE SOLUTION
Unit does not function when Main • No AC Power • Make certain AC power cord is plugged
Power Switch 1 is pushed into a live outlet
• Check to see if outlet is switch controlled
Display lights, but no sound • Intermittent input connections • Make certain that all input and speaker
or picture connections are secure
• Mute is on • Press Mute button G
• Volume control is down • Turn up volume control
No sound from any speaker; • Amplifier is in protection mode • Check speaker-wire connections for shorts at receiver
Protect Warning in Display due to possible short and speaker ends
• Amplifier is in protection mode • Contact your local Harman Kardon service depot
due to internal problems
No sound from surround or • Incorrect surround mode • Select a mode other than Stereo
center speakers • Input is mono • There is no surround information from mono sources (except with
Theater and Hall surround modes)
• Incorrect configuration • Check speaker mode configuration
• Stereo or Mono program material • Some surround modes may not create rear-channel information
from nonencoded programs
Unit does not respond to • Weak batteries in remote • Change remote batteries
remote commands • Wrong device selected • Press the AVR Selector 5
• Remote sensor Ó is obscured • Make certain front-panel sensor is visible to remote or
connect remote sensor
Intermittent buzzing in tuner • Local interference • Move unit or antenna away from computers, fluorescent lights,
motors or other electrical appliances
Letters flash in the Channel Indicator • Digital audio feed paused • Resume play for DVD
Display $ and Digital Audio stops • Check that Digital Signal is fed to the Digital Input selected
No picture or on-screen • AVR Resolution to Display • Select correct Resolution as described

information on the TV screen. is not correct, too high or too low. on page 21 "Resolution To Display"
Processor Reset To clear the AVR’s entire system memory NOTE: Resetting the processor will erase any
including tuner presets, output level settings, configuration settings you have made for
In the rare case where the unit’s operation or the delay times and speaker configuration data, first speakers, output levels, surround modes, digital
displays seem abnormal, the cause may involve put the unit in Standby by pressing the System input assignments as well as the tuner presets.
the erratic operation of the system’s memory or Power Control button 2. Next press and hold After a reset the unit will be returned to the
microprocessor. the OK button 6 for five seconds. factory presets, and all settings for these items
must be reentered.
To correct this problem, first unplug the unit from The unit will turn on automatically and show the
the AC wall outlet and wait at least three word RESET in the Display for a few seconds. If the system is still operating incorrectly, there
minutes. After the pause, reconnect the AC Then it reverts to normal ON status. Note that may have been an electronic discharge or severe
power cord and check the unit’s operation. If the once you have cleared the memory in this manner, AC line interference that has corrupted the
system still malfunctions, a system reset may it is necessary to re-establish all system memory or microprocessor.
clear the problem. configuration settings and tuner presets.
If these steps do not solve the problem, consult
an authorized Harman Kardon service depot.
Page 4 of 125
Programming the Remote
ENGLISH
Notes on Using the AVR Punch-Through Programming Resetting the Remote Memory
Remote With Other Devices.
• Manufacturers may use different code sets for The AVR 355/AVR 255 remote’s punch-through As you add components to your home-theater
the same product category. For that reason, it is feature allows you to select one component for system, occasionally you may wish to totally
important that you check to see if the code set the remote to operate, while simultaneously set- reprogram the remote control without the
you have entered operates as many controls as ting certain groups of controls to operate anoth- confusion of any commands, activities or ”Punch-
possible. If it appears that only a few functions er component. For example, while using the AVR Through“ programming that you may have done.
operate, check to see if another code set will to control surround modes and other audio func- To do this, it is possible to reset the remote to the
work with more buttons. tions, you may operate the transport controls of original factory defaults and command codes by
your DVD player. Or while using the remote to following these steps. Note, however, that once
• Depending on the brand and product type the remote is reset, all commands or codes that
used the functions listed in the Function List control video functions on your TV, you may use
you have entered will be erased and will need to
tables may not correspond with the function the your cable box to change channels.
be re-entered:
unit reacts on the command. In these cases it’s a To program punch-through control while operat-
good idea to edit the reaction of the unit into 1. Press the TV Device Button c and the "0"
ing any device: number Button k simultaneously. The TV button
the corresponding line of the table or to set up a
separate list. 1. Press and hold the Source Selector (or AVR lights up.
selector) for the main device the remote will 2. Press the ”3“ button k three times.
• When a button is pressed on the AVR remote,
the red light under the Input Selector cy be operating. The Source Selector will light, go 3. After a number of seconds, depending on the
for the product being operated should flash dark and then light up again, indicating the number of commands that are programmed and
briefly. If the Device Control Selector flashes for remote is in Program mode and that you may need erasing, all the Device Buttons c as well as
some but not all buttons for a particular release the button. the AVR Button y blink 3 times to indicate that
product, it does NOT indicate a problem with the the remote has been reset to the factory settings.
2. Select the type of punch-through program-
remote, but rather that no function is
ming.
programmed for the button being pushed.
a) To program channel control punch-through,
press the Channel Up Button.
b) To program transport control punch-
through, press the Play Button.
3. Press the Source Selector for the device whose
channel or transport controls you would like
to be active while operating the device you
selected in the first step. The Source Selector
will flash to confirm the programming.
For example, if you wish to watch your TV while
changing channels using your cable box, first
press the TV Button until it lights. Then press the
Channel Up Button, followed by the CBL/SAT
Button.
To undo punch-through programming, follow
the same steps as above, but press the same
Source Selector in Steps 1 and 3.
NOTE: The remote always allows volume-control
punchthrough, since the Volume and Mute con-
trols are dedicated to the AVR.
Page 5 of 125
AVR355/230
1. Instruction manual ass'y - Accessories 2. Package Drawing
7 MICROPHONE ASS'Y
1 2 3 4
1 MANUAL ASS'Y
POLY BAG AM LOOP ANTENNA ASS'Y BATTERY ASS'Y FM 1 POLE ANT
5 6 7 8 2 REMOCON ASS'Y
3 SNOW PAD (L)

REMOCON ASS'Y
CORD , POWER(EUR) COVER ASS'Y IMAGE BROCHURES
4 SNOW PAD (R)
9 10 11 12
5 SET
STAPLE BOOKLET,INFORMATION MANUAL INSTRUCTION
POLY BAG
6 BOX ,OUT CARTON

13 14
MANUAL SETUP GUIDE STAPLE
A B
ACCESSORY-1 7 ACCESSORY-2
NO DESCRIPTION PARTS NO. Q,ty
1 POLY BAG CPB1061W 1
2 AM LOOP ANTENNA ASS'Y CSA1A027Z 1
3 BATTERY CABR03P 6 REMOCON ASS'Y MICROPHONE ASS'Y
4 FM 1 POL ANT CSA1A018Z 1

ACCESSORY-2
5 CORD , POWER CJA2B054Z 1
NO DESCRIPTION PARTS NO. Q,ty
6 COVER ASS'Y CGRAVR350/230ZA 1 NO DESCRIPTION PARTS NO. Q,ty
10 POLY BAG CPB1061W 1
1 COVER A CGR2A436 1 1 ACCESSORY-1 CQXAVR355/230 1
11 BOOKLET,INFORMATION CQE1A180Z 1
2 COVER B CGR2A437 1
12 MANUAL,INSTRUCTION CQX1A1318Z 1 2 REMOCON ASS'Y CARTAVR355/230 1
3 ORNAMENT , AL A CGX1A391C66 1
13 MANUAL ,SETUP GUIDE CQX1A1320Z 1 3 SNOW,PAD(L) CPS6A564 1
4 ORNAMENT , AL B CGX1A392C66 1
14 STAPLE CPL0905 3 4 SNOW,PAD(R) CPS6A565 1
5 SHEET,FRONT COVER CQE1A220Z 1
6 PAD , COVER CPS1A676 1 5 SET AVR355/230SET 1

A REMOCON ASS'Y CARTAVR355/230 1
7 BAG , POLY CPB1A176Z 1 6 BOX,OUT CARTON CPG1A855U 1
B MICROPHONE ASS'Y CJXAVR340MICRO 1
7 IMAGE BROCHURES HQE1A273Z 1 7 ACCESSORY-2 CQXAVR355/230 1
8 REMOCON ASS'Y CARTZONE24 1
8 MICROPHONE ASS'Y CJXAVR340MICRO 1
9 STAPLE CPL0905 3
Page 6 of 125

DISASSEMBLY harman/kardon AVR 355/230 Service Manual
AVR355/230
1. Removing the Top Cabinet 3. Removing the Rear Panel

Remove the Screws 1 ~ 13 Remove the Screws 1 ~ 34
10
9
11
6 7 12 11 10 9 8 4 3 2 1 7 6 5
13
4 8 14
15
16
0N
OFF
17
5 12
18
19
13
20
21
22
3
23 24 25 26 27 28 28 30 31 32 33 34 35
1
4. Removing the Main PCB

Remove the Screws 1 ~7
2. Removing the Front Panel

Remove the Screws 1 ~ 9
9
1
8 2
5
6
3
7 4
7
5
1
4
2
3
Page 7 of 125

harman/kardon
AVR355/230 EXPLODED VIEW AVR 355/230 Service Manual
54
S10
S15
33
42 S8
36 40-4 40-1
S5
41
S5 40-3
S5
53 39-1
S1 S13 S8
S15 S15 S8
S6 S15
32
53
43 S7
S16
40-5
S9 x2
31
S6
S7
S10
S13 44
30
52 51 45
29
50 38-1
40-7
38-2 S12
S10 S10
S10
23
39-2 S5
S10
25 30
S11 46
S14
S5 S5
28 NO DESCRIPTION PARTS NO. Q,ty REMARK
22 40-2
1
2
ORNAMENT,VOLUME
CAP,VOLUME
CGU1A318Y
CGX1A338MBC63
1
1
3 HOLDER,VOLUME CMH1A214 1
21 27 4 INDICATOR,VOLUME CGL1A222 1
5 BADGE, HARMAN/KARDON CGB1A158Y 1
24 26 6 SHEET,AL FRONT CGX1A390C66X 1
25 47 7 WINDOW , FIP CGU1A410A25W 1
S2 8 BADGE,AVR355 CGB1A194Z 1
S6 9 FILTER , FIP CMZ1A127 1
20 10 KNOB , STANDBY CBT1A1064 1
48 11
12
KNOB , BACK
PANEL , FRONT
CBT1A1065
CGW1A447RHVB24
1
1
13 INDICATOR , POWER CGL1A265Y 1
14 PLATE , EARTH CMC2A338 2
15 BRACKET , SIDE CMD2A443 1
37-5 16 PLATE , SHIELD CMC1A323 1
49 17
18
PLATE , EARTH
PLATE,EARTH
CMC2A325
CMC2A326
1
1
S2 S11 19 HOLDER , LED CMH2A215 1
20 BRACKET,FIP CMD1A209 2
21 CABINET,TOP CKC6B145S60 1
13 22
23
CHASSIS,BOTTOM
FOOT A
CUA1A282
CKL1A094
1
2
37-1 37-6 S3 24 24 FOOT B CKL1A095 2
25 CUSHION , FOOT CHG1A373 4
S11 26 HEAT SINK CMY1A303 1
12 S3 27 BRACKET,PCB CMD1A417 2
25 28 HOLDER,PCB CHE170 2
29 BRACKET,TRANS CMD2A487 1
S3 30 BRACKET,PCB(H/T) CMD1A398 2
10 31
32
BRACKET,PCB
BRACKET,PCB
CMD1A636
CMD1A387
1
2
33 PANEL,REAR CKF8A337Z 1
37-2 34
23 35
9
37-4 S11 36 TRANS,POWER CLT5W033ZE 1
37 FRONT PCB ASS'Y COP12053J 1
8 25 37-1 FIP & KEY PCB 1
19 S2 37-2 VOLUME PCB 1
37-3 PHONE PCB 1
37-4 VIDEO PCB 1
7 S3 18 37-5 POWER LED PCB 1
37-3
S2 37-6 GUIDE PCB(CARD CABLE) 1
1
1
NO DESCRIPTION PARTS NO. Q,ty 38 MAIN PCB ASS'Y COP12026J 1

S1 SCREW CTB3+8JFZR 13 38-1 MAIN PCB 1
15 S2 SCREW CTB4+6FFZR 6 38-2 GUIDE PCB(CARD CABLE) 1
6 11 S3 SCREW CTB3+10JR 29
39 INPUT PCB ASS'Y COP12029J 1
17 S4 SCREW CTWS3+10GR 1 39-1 INPUT PCB 1
S5 SCREW CTB3+10JFZR 26 39-2 ADD PCB
5 14 16 S6 SCREW CTB3+6JR 15
S7 SCREW CTB3+8JR 10
40 POWER PCB ASS'Y COP12027J 1
S8 SCREW CTB3+6FFZR 12 40-1 DIGITAL IN/OUT PCB 1
S1 S9 SCREW CTW3+12JR 2
4 S1 40-2 REGULATOR PCB(A) 9
S10 SCREW CTW3+8JR 6 40-3 TRANS PCB 1
40-4 TRANS PCB 1
S11 SCREW CT33+8JFZR 4
40-5 REGULATOR PCB(B) 1
S12 SCREW CHD1A012R 21 40-6 REGULATOR PCB(C) 1
3 S13 SCREW CHD3A012R 21 40-7 REMOTE PCB 1
S14 SCREW CHD4A012ZR 5 41 VIDEO PCB ASS'Y COP12033J 1
42 HDMI PCB ASS'Y COP12035J 1
S15 SCREW,TRANS CHD1A023R 4
43 REGULATOR PCB ASS'Y COP12055J 1
S16 SCREW, SPECIAL CHD1A036R 4
2 44
45
MULTI PCB ASS'Y
TUNER MODULE
COP12036J
CNVM9014MS171L
1
1
46 CUSHION CHG1A160Z 1
47 SUPPORT,CUSHION CHG1A104Z 2
48 RUBBER CHG1A309 1
49 BRACKET, SIDE(L) CMD1A555 1
50 HEAT SINK CMY2A249 1
1 51 BRACKET, FAN CMD1A600 1
52 BRACKET, FAN CMD2A615 1
53 FAN , MOTOR CFNCF12825HSN 2
54 MOMS SW ASS'Y CSHAVR155ZA 2
Page 8 of 125

AVR355/230 Electrical Parts List

Ref. # Part Number Description Value
CGB1A194Z BADGE , AVR355 BADGE
CGL1A222 INDICATOR , VOLUME INDICATOR
CGU1A318Y ORNAMENT , VOLUME AVR255 ORNAMENT
CGU1A410A25W WINDOW , FIP WINDOW
CARTAVR355/230 REMOCON TRANSMITTER ASS'Y ASS'Y
CHE154 CLAMPER , ARM CLAMPER
CJXAVR340MICRO MICRO PHONE ASS'Y MICRO PHONE
CPG1A855U BOX , OUT CARTON AVR355/230 BOX
CPS6A564 PAD , SNOW L SNOW PAD
CPS6A565 PAD , SNOW R SNOW PAD
CQB1A551Z LABEL , BAR CODE LABEL
CQB1A797Z LABEL , HDMI LABEL
CQB1A876Z LABEL , COUNTRY DVD29/230 LABEL
CQS1A001 RIBON , BAR CODE RIBON
CQXAVR355/230 INSTRUCTION MANUAL ASS'Y ASS'Y
CARTZONE24 AVR355 REMOCON TRANSMITTER ASS'Y ASS'Y
CGRAVR350/230ZA COVER ASS'Y COVER
CGR2A436 COVER , A AVR350 COVER
CGR2A437 COVER , B AVR350 COVER
CGX1A391C66 ORNAMENT , AL A AVR350 ORNAMENT
CGX1A392C66 ORNAMENT , AL B AVR350 ORNAMENT
CJA2B054Z CORD , POWER(DETACHABLE/EUR) POWER CORD
CQX1A1318Z MANUAL , INSRTUCTION MANUAL
CQX1A1320Z MANUAL , SETUP AVR155/230 MANUAL
CSA1A018Z FM 1 POLE ANT FM ANT
CSA1A027Z AM LOOP ANT AM ANT
CRE1A037 LOCKER SH08M790BO
CGX1A338MBC63 CAP , VOLUME VOLUME CAP
CGX1A390C66X SHEET , AL FRONT AVR255 SHEET
CKC6B145S60 CABINET , TOP AVR350 CABINET
CMH1A214 HOLDER , VOLUME HOLDER
CMZ1A127 FILTER , FIP AVR255 FILTER
CMZ2A090 SHEET , VOLUME SHEET
FRONT PANEL ASSY

CGWAVR355/230 FRONT PANEL ASS'Y ASS'Y
CBT1A1064 KNOB , STANDBY AVR355 KNOB
CBT1A1065 KNOB , BACK AVR355 KNOB
CGB1A158Y BADGE , FRONT HARMAN/KARDON BADGE
CGL1A265Y INDICATOR , POWER AVR155 INDICATOR
CGW1A447RHVB24 PANEL , FRONT AVR355/230 PANEL
CHG1A309 RUBBER RUBBER
CHR301 CLAMPER CLAMPER
CHS1A032 TAPE , HEMELON TAPE
CLZ9Z028Z FERRITE CORE(21.2X6.4X12.7) FERRITE CORE
CMC1A323 PLATE , SHIELD AVR350 PLATE
CMC2A326 PLATE , EARTH AVR350 PLATE
CMC2A338 PLATE , EARTH AVR350 PLATE
CMD1A555 BRACKET , SIDE (L) BRACKET
CMD2A443 BRACKET , SIDE BRACKET
CMH2A215 HOLDER , LED AVR350 HOLDER
CPE1A009 SHEET , BLIND SHEET
CTB3+10JR SCREW SCREW
CTWS3+10GR SCREW SCREW
Page 9 of 125
FRONT PANEL ASSY

CB72 CWC4F2A17A280B CABLE , CARD(17P, 280mm) CARD CABLE
BOTTOM CHASSIS ASS'Y

CUAAVR355/230 BOTTOM CHAASIS ASS'Y ASS'Y
CHD1A012ZR SCREW , SPECIAL SCREW
CHD1A023R SCREW , SPECIAL SCREW
CHE170 HOLDER , PCB HOLDER
CHE36-3 CLAMPER , WIRE CLAMPER
CHG1A104Z CUSHION , RUBBER CUSION
CHG1A160Z CUSHION , RUBBER CUSION
CHG1A373 CUSHION , FOOT AVR350 CUSION
CHG1A412 CUSHION CUSION
CKF8A337Z PANEL , REAR AVR355/230 PANEL
CKL1A094 FOOT , A AVR350 FOOT
CKL1A095 FOOT , B AVR350 FOOT
CMD1A636 BRACKET , PCB BRACKET
CMD2A487 BRACKET , TRANS BRACKET
CNVM9014MS171L MODULE , TUNER(EUR) TUNER
CTB3+10JFZR SCREW SCREW
CTB3+6FFZR SCREW SCREW
CTS3+8JFZR SCREW SCREW
CTW3+12JR SCREW SCREW
CUA1A282 CHASSIS , BOTTOM AVR255 CHASSIS
BN90 CSHAVR155ZA MOMS SW ASS'Y SW ASS'Y
CSH1A009ZV SWITCH , MOMS SWITCH
CWZAVR255ZA WIRE , ASS'Y(2P,150mm) WIRE
BN92 CWZSR4001BN91A WIRE ASS'Y WIRE
CLZ9W003Z FERRITE , RING 29X7.7X19
CWZSR4001BN91 WIRE ASS'Y WIRE
CB11 CWC4F2A17A100B CABLE , CARD(17P, 100MM, 1MM, B-TYPE) CARD CABLE
CB12 CWC1C4A21B110B CABLE , CARD CARD CABLE
CB13 CWC4C4A13B100B CABLE , CARD CARD CABLE
CB14 CWC4F2A17A100B CABLE , CARD(17P, 100MM, 1MM, B-TYPE) CARD CABLE
CB19 CWC4F2A07A080B CABLE , CARD(7P, 80mm, B TYPE) CARD CABLE
CB47 CWC4F2A07A120B CABLE , CARD (7P, 120MM, 1MM) CARD CABLE
F901 KBA2C6300TLEZ FUSE(233TYPE, 6.3A,250V) LITTEL FUSE
RC91 CJJ8A006ZW RECEPTACLE , AC(15A/250V,R-301,B21) INNET
T901 CLT5W033ZE TRANS , POWER AVR355/230 MAINTRANS
FRONT PCB ASSY

COP12053J AVR355/230 FRONT PCB ASS'Y ASS'Y
C714 CCBS1H151KBT CAP , CERAMIC(150PF/50V) 150UF 50V K
C716 CCEA1AH331T CAP , ELECT 330UF 10V
C719 CCBS1H102KBT CAP , CERAMIC(1000PF/50V) 1000PF 50V K
C723 CCBS1H104ZFT CAP , CERAMIC 0.1UF 50V Z
C729 CCBS1H473ZFT CAP , CERAMIC(47000PF/50V) 0.047UF 50V Z
C735 CCEA1CKS100T CAP , ELECT 10UF 16V
Page 10 of 125
FRONT PCB ASSY

C794 CCBS1C222MXT CAP , CERAMIC(2200PF/16V) 2200PF 16V
C808 CCBS1H181KBT CAP , CERAMIC(180PF/50V) 180PF 50V
C817 CCBS1H100JCT CAP , CERAMIC(10PF/50V) 10PF 50V
C820 CCEA1HH100T CAP , ELECT 10UF 50V
C821 CCEA1EH470T CAP , ELECT 47UF 25V
C828 CCBS1H470JT CAP , CERAMIC(47PF/50V) 47PF 50V
C830 CCBS1H473ZFT CAP , CERAMIC(47000PF/50V) 0.047F 50V
C872 CCEA1CH331T CAP , ELECT 330UF 16V
C903 CCEA1HKS2R2T CAP , ELECT 2.2UF 50V SMALL SIZE
D455 CVD1SS133MT DIODE 1SS133
L702 HLQ02C100KT COIL , AXAIL 10uH
Q451 HVTKRC107MT T.R KRC107M
Q452 HVTKRA107MT T.R KRA107M
Page 11 of 125
FRONT PCB ASSY

Q734 HVTKTC2874BT T.R , MUTE KTC2874B
Q739 HVTKTA1271YT T.R KTA1271Y
Q740 HVTKTC3200GRT T.R KTC3200GR
R452 CRD20TJ103T RES , CARBON 10K OHM 1/5W J
R453 CRD20TJ362T RES , CARBON 3.6K OHM 1/5W J
R704 CRD20TJ100T RES , CARBON 10 OHM 1/5W J
R753 CRD20TF1001T RES , CARBON 1K /1/5W /F
R754 CRD20TF1501T RES , CARBON 1.5K /1/5W /F
R756 CRD20TF2701T RES , CARBON 2.7K /1/5W/F
R758 CRD20TF5601T RES , CARBON(5.6K/F) 5.6K /1/5W/F
R759 CRD20TF1001T RES , CARBON 1K /1/5W /F
R764 CRD20TF5601T RES , CARBON(5.6K/F) 5.6K /1/5W/F
R765 CRD20TF7501T RES , CARBON (7.5K/F) 7.5K /1/5W/F
R824 CRD20TF2200T RES , CARBON(220 OHM, 1%) 220 OHM /1/5W /F
R825 CRD20TF6800T RES , CARBON(680 OHM, 1%) 680 OHM /1/5W /F
Page 12 of 125
FRONT PCB ASSY

S701 HST1A020ZT SW , TACT TACT SWITCH
CMC2A325 PLATE , EARTH AVR155 Plate, earth
BK71 CMD1A209 BRACKET , FLT BRACKET
BK72 CMD1A209 BRACKET , FLT BRACKET
BN10 CWZAVR155BN10 SHIELD WIRE ASS'Y(5P, 2MM, 350MM) WIRE
BN18 CWZAVR355BN18 SHIELD WIRE ASS'Y (5P, 500MM) WIRE
BN22 CWZAVR155BN22 WIRE ASS'Y(7P, 2MM, 500MM) WIRE
Page 13 of 125
FRONT PCB ASSY

BN41 CWZAVR155BN41 SHIELD WIRE ASS'Y(7P, 2MM, 500MM) WIRE
BN81 CWB1C907200BM WIRE ASS'Y WIRE
BN84 CWB2B905080EN WIRE ASS'Y WIRE
CN72 CJP17GA117ZY WAFER WAFER
CN84 CJP05GB46ZY WAFER WAFER
CN85 CJP03GA19ZY WAFER , STRAIGHT(3PIN) WAFER
CN88 CJP05GA19ZY WAFER , STRAIGHT WAFER
D701 CVD1L0345W31BOCT201V L.E.D , WHITE LED
D723 CVD30ASOGCAA-S7 L.E.D , ORANGE LED
D778 HVD1N5819T DIODE , SCHOTTKY 1N5819
ET03 CMD1A629 BRACKET , PCB BRACKET
FIP1 CFL17BT031GINK F.I.P , AVR355 FIP(FUTABA)
IC73 HRVNJL34H380A SENSOR , REMOCON SENSOR
IC75 HVI74ACT04MTR I.C , HEX JRC(74ACT04MTR)
IC76 HVI74HCU04AFNG I.C , INVERTER FAIRCHILD(74HCU04AFN
IC86 HVINJM4556AL I.C , HEADPHONE JRC(NJM4556AL)
IC87 HVINJM2068MTE1 I.C , OP AMP JRC(NJM2068MTE1)
JK81 CJJ4M041Y JACK , BOARD (COAX) JACK
JK82 HJSTORX177L MODULE , OPTICAL(RX) OPT JACK
JK83 CJJ2E026Z JACK , HEADPHONE(SILVER PLATE) HEADPHONE JACK
JK85 CJJ9M004Y JACK , S-VHS (SILVER) S-VHS JACK
JK86 CJJ4S028Y JACK , BOARD (3P SILVER) JACK
JW83 CWE8202150RV WIRE ASS'Y WIRE
RL45 CSL4A016ZU RELAY , 12V 2C2P RELAY
VR74 CSR2A037Z ENCODER ENCODER
MAIN PCB ASSY

COP12026J AVR355/230 MAIN PCB ASS'YY ASS'Y
C506 CCKT1H331KB CAP , CERAMIC 330PF 50V
C509 CCKT1H331KB CAP , CERAMIC 330PF 50V
Page 14 of 125
MAIN PCB ASSY

C601 CCCT1H120JC CAP , CERAMIC 12PF 50V J
C721 CCKT1H221KB CAP , CERAMIC 220PF 50V K
C900 HCQI1H473JZT CAP , MYLAR 0.047UF 50V J
C905 CCFT1H223ZF CAP , CERAMIC 0.022UF 50V Z
C913 CCFT1H104ZF CAP , SEMICONDUCTOR 0.1UF 50V Z
C920 CCEA1VH221T CAP , ELECT 220UF 35V
Page 15 of 125
MAIN PCB ASSY

C939 CCEA1HH4R7T CAP , ELECT 4.7UF 50V
C971 HCQI1H562JZT CAP , MYLAR 5600PF 50V J
C991 CCEA1HH1R0T CAP , ELECT 1UF 50V
D901 CVD1N4003SRT DIODE , RECT 1N4003
D903 CVD1N4003ST DIODE , RECT 1N4003
Page 16 of 125
MAIN PCB ASSY

D979 CVDZJ5.1BT DIODE , ZENER ZJ5.1B 1/2W
ET90 HJT1A025 PALTE , EARTH MET37-0002
ET91 HJT1A025 PALTE , EARTH MET37-0002
F901 KJCFC5S HOLDER , FUSE HOLDER
F902 KBA2D2500TLET FUSE(SR-5,2.5A,250V) SAVE FUSETECH
IC97 HVIRE5VT28CATZ I.C , RESET RESET
Q501 HVTKTA1268GRT T.R KTA1268GR
Q541 HVTKTC3198YT T.R KTC3198Y
Q681 HVTKSC2785YT T.R KSC2785Y
Page 17 of 125
MAIN PCB ASSY

Q961 HVTKTA1024YT T.R A1024Y
Page 18 of 125
MAIN PCB ASSY

Page 19 of 125
MAIN PCB ASSY

R631 CRD25FJ180T RES , CARBON 18 OHM 1/5W J
R646 CRD25FJ3R3T RES , CARBON 3.3 OHM 1/4W J
Page 20 of 125
MAIN PCB ASSY

Page 21 of 125
MAIN PCB ASSY

R908 CRD20TJ105T RES , CARBON 1M OHM 1/5W J
Page 22 of 125
MAIN PCB ASSY

CMYAVR355 HEAT SINK ASS'Y ASS'Y
CFNCF12825HSN FAN , MOTOR FAN
CMD1A600 BRACKET , FAN BRACKET
CMD2A615 BRACKET , FAN BRACKET
CMY1A303 HEAT SINK HEAT SINK
Q652 HVT2SB1647-OKM T.R , POWER TR
Q657 HVT2SD2560-OKM T.R , POWER TR
CWE8202150AA WIRE ASS'Y WIRE
C8AGB288 BOND (MAX) BOND
BN19 CWB3FE03250UP WIRE ASS'Y WIRE
BN20 CWB3FC04280UP WIRE ASS'Y WIRE
BN81 CWB1C902050EN WIRE ASS'Y WIRE
BN98 HJP08GA130ZK WAFER WAFER
CN12 CJP21GA115ZY WAFER , CARD CABLE WAFER
CN61 CJP02GA01ZY WAFER , STRAIGHT, 2PIN WAFER
Page 23 of 125
MAIN PCB ASSY

CN92 CJP02KA060ZY WAFER WAFER
C631 CCEA1JH221E CAP , ELECT 220UF 63V
C902 CCET63VKL5822NK CAP , ELECT 8200/63V (30*50)
C904 KCKDKS472ME CAP , CERAMIC(X1/Y2/SC) 0.0047UF/2.5KV
C906 CCEA1VH102E CAP , ELECT 1000UF 35V
C911 CCEA1EH471E CAP , ELECT 470UF/25V
IC94 HVIKIA7805API REGULATOR, +5V KEC(KIA7805API)
JK91 CJJ5R006Z TERMINAL , SPEAKER TERMINAL
JK92 CJJ5Q012Z TERMINAL , SPEAKER TERMINAL
JK97 CJJ4P041W JACK IN/OUT JACK
JK98 CJJ4P042W JACK IN/OUT JACK
JW90 CWE8212120VV WIRE , RED WIRE
JW91 CWE8212180VV WIRE ASS'Y WIRE
JW93 CWEE202110VV WIRE (BLACK) WIRE
L501 CLEY0R5KAK COIL , SPEAKER 0.5UH K
OL91 KJJ7A022Z OUTLET , AC(EUR/1P) A302D0061P
Q858 HVT2SA1360O T.R 2SA1360O
Q881 HVT2SC3423O T.R 2SC3423O
Page 24 of 125
MAIN PCB ASSY

RY94 HSL1A008ZE RELAY SDT-S-112DMR
R656 CRF5EKR27HX2K RES , CEMENT 0.27ohm X 2
R905 CRG1ANJ100H RES , METAL OXIDE FILM 10 OHM 1W J
TH91 KRTP42T7D330B THERMAL SENSOR , POSISTOR P42T7D330BW20
T902 CLT5J039ZE TRANS , SUB AVR355 TRANS
POWER PCB ASSY

COP12027J AVR355/230 POWER PCB ASS'Y ASS'Y
C104 CCBS1E103ZFT CAP , CERAMIC 0.01UF 25V
C119 CCEA1JH470TS CAP , ELECT 63V/47UF/105'C
C120 CCEA1JH470TS CAP , ELECT 63V/47UF/105'C
C912 CCEA0JH102T CAP , ELECT 1000UF 6.3V
Page 25 of 125
POWER PCB ASSY

C935 CCBS1H223ZFT CAP , CERAMIC 0.022UF 50V
D101 CVDZJ15BT DIODE , ZENER ZJ15B 1/2W
D102 HVDMTZJ27BT DIODE , ZENER MTZJ27B 1/2W
R108 CRD20TJ8R2T RES , CARBON 8.2 OHM 1/5W J
R110 CRD20TJ8R2T RES , CARBON 8.2 OHM 1/5W J
Page 26 of 125
POWER PCB ASSY

R956 CRD20TJ1R0T RES , CARBON 1 OHM 1/5W J
VR81 CVN1RA221B02T RES , SEMI FIXED (220, B CURVE) KVSF637AVC
CMD1A618 BRACKET , RESET BRACKET
BN17 CJP06GB143ZB FEMALE HEADER(6P, 2.54mm) HEADER
BN22 CWB1C902280NN WIRE ASS'Y WIRE
BN79 CWB1C907120EN WIRE ASS'Y(7P, 2MM, 120MM) WIRE
Page 27 of 125
POWER PCB ASSY

BN96 CWB1C915180EN WIRE ASS'Y(15P, 2MM, 180MM) WIRE
CN13 CJP05GA01ZY WAFER(YMW025-05R) WAFER
CN20 CJP04GA90ZM WAFER WAFER
CN31 CJP02GA19ZY WAFER , 2PIN WAFER
CN98 HJP08GB131ZK WAFER WAFER
C129 CCEA1EH822E CAP , ELECT(KR3, 8200UF/25V, 18X30) 8200UF 25V
C929 CCEA1VH222EZ CAP , ELECT (2200UF/35V, 12.5X31) 2200UF 35V
C930 CCEA1VH222EZ CAP , ELECT (2200UF/35V, 12.5X31) 2200UF 35V
C941 CCEA1EH682E CAP , ELECT(KR3, 25V/6800, 18X35.5) 6800UF 24V
C951 CCEA1HH102E CAP , ELECT 1000UF 50V
D701 HVDKBU804F DIODE , BRIDGE DIODE
D991 CVDKBU804FMA BRIDGE DIODE ASS'Y ASS'Y
CMY1A219 HEAT SINK (BRIDGE DIODE) HEAT SINK
HVDKBU804F DIODE , BRIDGE DIODE
K8AYG6260 COMPOUND , SILICONE SILICONE
D992 CVDKBU804FMA BRIDGE DIODE ASS'Y ASS'Y
CMY1A219 HEAT SINK (BRIDGE DIODE) HEAT SINK
HVDKBU804F DIODE , BRIDGE DIODE
K8AYG6260 COMPOUND , SILICONE SILICONE
IC81 CVIST232CDR IC , RS232C(SO-16TYPE) ST(ST232CDR)
IC89 HVIKIA278R05PI REGULATOR (5V OUTPUT LOW DROP) KEC(KIA278R05PI)
IC90 CVIKIA278R15PI I.C , REGULATOR(15V OUTPUT LOW DROP) KEC(KIA278R15PI)
IC91 CVIKIA7915PI I.C , REGULATOR(15V, TO-220AB) KEC(KIA7915PI)
IC97 BVIKP1010B IC, PHOTO COUPLER COSMO(KP1010B)
IC98 BVIKP1010B IC, PHOTO COUPLER COSMO(KP1010B)
IC99 HVI74LCX32TTR I.C , OR-GATE ST(74LCX32TTR)
JK75 HJSTORX177L MODULE , OPTICAL(RX) TORX177L
JK94 CJJ2D008Z JACK , STEREO JACK
JK97 CJJ9W001Z JACK , 9P D-SUB FEMALE(RS-232C, SEMCO)JACK
Q851 HVTKTD600KGR T.R , BIAS KTD600KGR
Page 28 of 125
POWER PCB ASSY

R104 KRQ1AJR47H RES , FUSE 0.47 OHM 1W J
R105 KRQ1AJR47H RES , FUSE 0.47 OHM 1W J
R106 CRQ1AJR33H RES , FUSE 0.33 OHM 1W J
SW95 CST1A010Z SW , TACT TACT SWITCH
SW96 HSH2B018Z SW , PUSH SPUJ19XSM011
SW97 HSH2B018Z SW , PUSH SPUJ19XSM011
INPUT PCB ASSY

COP12029J AVR355/230 INPUT PCB ASS'Y ASS'Y
CN11 CJP17GA193ZY WAFER, CARD CABLE (SMD) WAFER
CN16 CJP13GA193ZY WAFER , CARD CABLE (SMD) WAFER
C201 CCUS1H221JA CAP , CHIP 220PF 50V J
C260 CCUS1H104KC CAP , CHIP 0.1UF 50V K
C269 CCUS1A105KC CAP , CHIP 1UF 10V K
C295 CCUS1H272KC CAP , CHIP 2700PF 50V K
Page 29 of 125
INPUT PCB ASSY

C532 CCUS1H182KC CAP , CHIP(1800PF/50V/1608/X7R) 1800PF 50V K
Page 30 of 125
INPUT PCB ASSY

C701 CCUS1H150JA CAP , CHIP(15PF/50V) 15PF 50V J
Page 31 of 125
INPUT PCB ASSY

D201 CVD1SS355T DIODE , CHIP 1SS355T
D701 HVDRLS4148SR DIODE, SWITCHING, SMD TYPE RLS4148 TE-11
IC20 CVINJW1197CFC2 I.C , VOL WITH INPUT SELECTOR JRC(NJW1197CFC2)
IC21 HVINJM2068MTE1 I.C , OP AMP JRC(NJM2068M-TE1)
IC70 HVITC74VHC157FT I.C , 2-CHANNEL MUX ST(TC74VHC157FT)
IC71 CVIST25VF080B504CS2F I.C , 8 Mbit SPI Serial Flash SST(SST25VF080B-50-4C
IC72 HVITC74HCU04AFN IC , INVERTER TC74HCU04AFN
IC73 HVICS42528-CQ I.C , CODEC + DIR CIRRUS LOGIC(CS42528
IC74 HVILC72723M IC , PLL (RDS) SANYO(LC72723M)
Page 32 of 125
INPUT PCB ASSY

IC75 CVICS497004CQZ I.C , DSP CIRRUS LOGIC(CS49700
IC77 CVIM12L16161A5TG I.C, 16MB SDRAM ESMT(M12L16161A5TG)
IC78 HVINJM2391DL133 I.C , CHIP REGULATOR (+3.3V) JRC(NJM2391DL1-3.3)
IC79 CVIKIA1117S18 I.C , REGULATOR(SOT-223) KEC(KIA1117S)
IC80 CVITC74VCX541FT I,C , OCTAL BUS BUFFER TOSHIBA(TC74VCX841F
IC88 CVIKIA1117S33 I.C , REGULATOR(SOT-223) KEC(KIA1117S)
IC89 CVIM24C32WMN6TP I.C , EEPROM (32 Kbit) ST(M24C32WMN6TP)
IC90 CVIT5CC1 I.C , FLASH U-COM TOSHIBA(T5CC1)
IC91 HVI74ACT04MTR I.C , HEX ST(74ACT04MTR)
L701 CLZ9Z014Z FERRITE , CHIP BEAD(60ohm, 4516) HCB4516KF-600T60
L704 CLZ9R005Z FERRITE , CHIP BEAD(60ohm, 1608) HCB1608KF-600T30
Q729 HVTKRC107S T.R , CHIP KRC107S
Q735 HVTKRA107S TR, CHIP KRA107S
Q736 HVTKRA107S TR, CHIP KRA107S
Q738 CVTKRC103S T.R , CHIP KRC103S
RN61 CRJ104DJ103T RES , 4ARRAY (1608*4) 10K OHM/1608*4
RN64 CRJ104DJ101T RES , 4ARRAY (1608*4) 100 OHM/1608*4
R201 CRJ10DJ101T RES , CHIP 100 OHM
Page 33 of 125
INPUT PCB ASSY

R224 CRJ10DJ272T RES , CHIP 2.7K OHM
R227 CRJ10DJ474T RES , CHIP 470K OHM
R253 CRJ10DJ4R7T RES , CHIP 4.7 OHM
Page 34 of 125
INPUT PCB ASSY

R318 CRJ10DJ392T RES . CHIP 3.9K OHM
R321 CRJ10DJ512T RES , CHIP 5.1 OHM
Page 35 of 125
INPUT PCB ASSY

R717 CRJ10DJ0R0T RES , CHIP 0 OHM
Page 36 of 125
INPUT PCB ASSY

R760 CRJ10DJ105T RES , CHIP 1M OHM
R767 CRJ10DF5101T RES , CHIP 5.1K OHM 1%
Page 37 of 125
INPUT PCB ASSY

X702 HOX27000E180S CRYSTAL , CHIP(27MHZ,SMD) 27MHz
Page 38 of 125
INPUT PCB ASSY

IC87 HVIRE5VT28CATZ I.C , RESET RESET
Q731 HVTKSA1175YT T.R KSA1175Y
C8AGB288 BOND (MAX) BOND
BN11 CWZAVR154BN46 SHIELD WIRE ASS'Y WIRE
CN10 CJP05GB46ZY WAFER WAFER
CN17 CJP06GB142ZB PIN HEADER(6P, 2.54mm) HEADER
Page 39 of 125
INPUT PCB ASSY

C732 CCEA0JKR3222E CAP , ELECT 3300UF 6.3V
IC36 HVIKIA7808API I.C , REGULATOR +8V KEC(KIA7808API)
IC37 CVIKIA7908PI I.C , REGULATOR(TO-220IS) KEC(KIA7908PI)
JK11 CJJ4R019W TERMINAL , IN/OUT JACK
JK12 CJJ4P014W JACK , IN/OUT JACK
JK13 CJJ4R019W TERMINAL , IN/OUT JACK
JK14 CJJ4R037W JACK , BOARD JACK
JK78 CJJ4S022Z JACK , BOARD JACK
JW21 CWE7202070AA WIRE ASS'Y WIRE
X701 HOX24576E150TF CRYSTAL 24.576MHz
X703 HOX04332E200C CRYSTAL 4.332MHz
VIDEO PCB ASSY

COP12033J AVR355/230 VIDEO PCB ASS'Y ASS'Y
C556 CCUS1H070DA CAP , CHIP 7PF 50V D
C601 CCUS1H020CA CAP , CHIP 2PF 50V C
Page 40 of 125
VIDEO PCB ASSY

IC41 CVINJM2595MTE1 I.C , VIDEO S/W JRC(NJM2595MTE1)
IC44 CVIKIA1117S33 I.C , REGULATOR(SOT-223) KEC(KIA1117S33-RTK/P)
IC59 HVINJM2137MTE1 I.C, OP AMP JRC(NJM2137M-TE1)
R542 CRJ18AJ221T RES , CHIP 220 OHM
Page 41 of 125
VIDEO PCB ASSY

R543 CRJ18AJ221T RES , CHIP 220 OHM
R571 CRJ10DF7502T RES , CHIP(75K, 1608, 1%) 75K OHM 1%
R572 CRJ10DF4992T RES , CHIP(49.9K, 1608, 1%) 49.9K OHM 1%
R573 CRJ10DF7502T RES , CHIP(75K, 1608, 1%) 75K OHM 1%
R574 CRJ10DF4992T RES , CHIP(49.9K, 1608, 1%) 49.9K OHM 1%
C545 CCEA1CKS220T CAP , ELECT 22UF 16V SMALL SIZE
C546 CCEA1CKS220T CAP , ELECT 22UF 16V SMALL SIZE
Page 42 of 125
VIDEO PCB ASSY

BN14 CJP17GA117ZY WAFER WAFER
BN19 CJP07GA117ZY WAFER WAFER
BN42 CJP12GB142ZB PIN HEADER(12PIN, 2.54mm, ANGLE) PIN HEADER
BN81 CJP34TT215ZB PIN HEADER , DUAL ROW(34P, 2.0MM, H=19 PIN HEADER
CN42 CJP12GB143ZB PIN HEADER , DIP SOCKET(12PIN, 2.54mm, APIN HEADER
ET60 CMC1A214 PLATE , EARTH PLATE
IC47 CVITMP86F409NG I.C , IPOD UART BUFFER TOSHIBA(TMP86F409NG
JK40 CJJ9P003Z JACK , S-VIDEO+CVBS JACK
JK41 CJJ9R001Z JACK , S-VIDEO+CVBS JACK
JK42 CJJ9L010Z JACK , IPOD CONNECTOR JACK(MOLEX SD-52986-
JK62 CJJ4R045Z JACK , BOARD JACK
JK69 CJJ4R045Z JACK , BOARD JACK
JW51 CWE7202070AA WIRE ASS'Y WIRE
X503 HOX08000E160C CRYSTAL 8MHz 8MHz
HDMI TORINO PCB ASSY

COP12035J AVR355/230 HDMI TORINO PCB ASS`Y ASS'Y
CN81 CJP34HA213ZB PIN SOCKET , FEMALE(34P, 2.0MM) PIN SOCKET
C622 CCSJA0J220B CAP , CHIP TANTAL(A TYPE, 22uF/6.3V, ELNA22UF 6.3V
Page 43 of 125

C634 CCSJA1C100B CAP , CHIP TANTAL(A TYPE, 10uF/16V, ELNA10UF 16V
C642 CCUS1H123KC CAP , CHIP(1608, 50V/12NF) 0.012UF 50V
C643 CCUS1C154KC CAP , CHIP 0.15UF 16V K
C653 CCUI1C104KC CAP , CHIP(1005, 16V/0.1UF) 0.1UF 16V
C740 CCUS1H123KC CAP , CHIP(1608, 50V/12NF) 0.012UF 50V
C741 CCUS1C154KC CAP , CHIP 0.15UF 16V K
Page 44 of 125

Page 45 of 125

Page 46 of 125

Page 47 of 125

D941 HVD1SR159-200 DIODE , SCHOTTKEY BARRIER DIODE
IC61 CVINJM2845DL118 IC, NJM2845DL1-18(TE1) JRC(NJM2845DL1-18)
IC62 HVINJM2391DL133 I.C , CHIP REGULATOR (+3.3V) JRC(NJM2391DL1-33)
IC65 CVINJM2845DL118 IC, NJM2845DL1-18(TE1) JRC(NJM2845DL1-18)
IC71 CVINJM2566V I.C , NJM2566AV(TE1) JRC(NJM2566AV)
IC72 CVIADV7342BSTZ I.C , VIDEO ENCODER ANLOG DEVICE(ADV734
IC73 CVIMK2302S01T I.C , BUFFER IDT(MK23020S-01T)
IC74 CVINJM2845DL133 I.C , REGULATOR(3.3V, TO-252-3) JRC(NJM2845DL1-13)
IC75 CVIA3S56D40ETPG5 I.C, 256MB DDR SDRAM ZENTEL(A3S56D40ETPG
IC76 CVIA3S56D40ETPG5 I.C, 256MB DDR SDRAM ZENTEL(A3S56D40ETPG
IC77 CVIES29LV320ET70TG I.C , FLASH ROM 32Mbit IC (TOP BOOST) EXCEL SEMI(ES29LV320
IC81 CVIFLI30336AC I.C , VIDEO PROCESSOR GENESIS(FLI30336)
IC82 CVIST232CDR IC , RS232C(SO-16TYPE) ST(ST232CDR)
IC84 HVIKIC7SZ08FU I.C ,INPUT AND GATE (USV PACKAGE) KEC(KIC7SZ08FU-RTK)
IC91 CVITC74VHCT14AFT I.C , HEX SCHMITT INVERTER(14PIN, TSSOPTOSHIBA(TC74VHC14AF
IC92 CVISII9185CTU IC , HDMI SW(80PIN, TQFP) SILICON IMAGE(SII9185C
IC93 CVISII9135CTU IC , HDMI RX(144PIN, TQFP) SILICON IMAGE(SII9135C
IC94 CVISII9134CTU IC , HDMI TX(100PIN, TQFP) SILICON IMAGE(SII9134C
IC95 HVIKIC7SZ08FU I.C ,INPUT AND GATE (USV PACKAGE) KEC(KIC7SZ08FU-RTK)
IC96 CVITC74VCX541FT I,C , OCTAL BUS BUFFER TOSHIBA(TC74VCX541F
JK91 HJJ9H003Z JACK , HDMI(JALCO) YKF45-7009
Page 48 of 125

L823 CLZ9R009Z CHOKE COIL, CHIP ( FOR HDMI ) CMM21T-900M-3H
Q901 HVTKRA102S T.R , CHIP KRA102S
Q903 CVTUPA672T F.E.T UPA672T
Q909 HVTKRC111S TR , CHIP KRC111S
RN31 CRJ064IJ330T RES , CHIP NETWORK(1/16W, 33ohm, 1005X4MNR04M0APJ330
Page 49 of 125

RN71 CRJ062IJ330T RES , CHIP NETWORK(1/16W, 33ohm, 1005X233 OHM 1/16W
Page 50 of 125

R854 CRJ10DF6801T RES, CHIP 1% 6.8K OHM 1%
R855 CRJ10DF4301T RES, CHIP 1% 4.3K OHM 1%
R864 CRJ10DF2800T RES , CHIP(1/10W, 280ohm, 1608, 1%) 280 OHM 1%
R865 CRJ10DF2800T RES , CHIP(1/10W, 280ohm, 1608, 1%) 280 OHM 1%
R867 CRJ10DF1002T RES , CHIP 1% 10K /1/10W/F
R868 CRJ10DF1002T RES , CHIP 1% 10K /1/10W/F
R897 CRJ10DJ200T RES , CHIP(1/10W, 20OHM,1608) 20 OHM
R898 CRJ10DJ200T RES , CHIP(1/10W, 20OHM,1608) 20 OHM
Page 51 of 125

R952 CRJ10DJ105T RES , CHIP 1M OHM
Page 52 of 125

X901 HOX27000E180S CRYSTAL , CHIP(27MHZ,SMD) 27MHz
X902 COX19660E330S X-TAL, CHIP, 19.6608 MHz ( 33P ) 19.6608MHz
BN50 CJP05GA19ZY WAFER , STRAIGHT WAFER
MULTI PCB ASSY(A-BUS)

COP12036J AVR355/230 MULTI PCB ASS'Y ASS'Y
CN16 CJP13GA193ZY WAFER , CARD CABLE (SMD) WAFER
IC44 HVINJW1159M I.C , VOLUME (2-CH) JRC(NJW1159M)
Q456 HVTKRA107ST T.R , CHIP KRA107S
Page 53 of 125
MULTI PCB ASSY(A-BUS)

R485 CRJ14CJ101T RES , CHIP 1/4W 100 OHM
D447 HVDMTZJ12BT DIODE , ZENER MTZJ12B 1/2W
Q457 HVTKSA1175YT T.R KSA1175Y(DEAD)
C450 CCEA1VH471E CAP , ELECT 470UF 35V
IC52 BVIKP1010B IC, PHOTO COUPLER COSMO
JK16 CJJ4N076Z JACK , IN/OUT JACK
JK17 CJJ9L004Z JACK , RJ-45 JACK
COP12055J AVR355/230 REGULATOR PCB ASS'Y ASS'Y

Page 54 of 125
REGULATOR PCB ASSY

C212 HCBS1H104ZFT CAP , CERAMIC 0.1UF 50V
R211 CRD20TF4700T RES , CARBON 470 OHM 1%
R212 CRD20TF2000T RES , CARBON 200 OHM 1%
BN43 CWB1C903150BM WIRE ASS'Y(3P, 150MM, 2.5MM, #24) WIRE
BN82 CWB1C905100BM WIRE ASS'Y (5P, 2.5P, 150mm) WIRE
D956 HVD2A04H DIODE , RECT(2A) DIODE
IC21 CVIKIA278R00PI I.C , REGULATOR(TO-220IS-4) KEC(KIA278R00PI)
IC22 CVIKIA7824API I.C , REGULATOR(24V TO-220IS) KEC(KIA7824API)
IC23 HVIKIA378R05PI I.C , REGULATOR(TO-220IS-4) KEC(KIA378R05PI)
IC31 CVIKIA278R00PI I.C , REGULATOR(TO-220IS-4) KEC(KIA278R00PI)
IC32 CVIKIA378R09PI I.C , REGULATOR(+9V, 3A, TO-220IS-4) KEC(KIA378R09PI)
IC93 CVIKIA7905PI I.C , REGULATOR(-5V) KEC(KIA7905PI)
IC94 HVIKIA7809API I.C , REGULATOR +9V KEC(KIA7809API)
Page 55 of 125
(7 0 Ω ) E
Darlington 2SB1647 B
Equivalent circuit C
Silicon PNP Epitaxial Planar Transistor (Complement to type 2SD2560) Application : Audio, Series Regulator and General Purpose
■Absolute maximum ratings (Ta=25°C) ■Electrical Characteristics (Ta=25°C) External Dimensions MT-100(TO3P)
Symbol 2SB1647 Unit Symbol Conditions 2SB1647 Unit
VCBO ICBO –100max µA 15.6±0.4 4.8±0.2
5.0±0.2
–150 V VCB=–150V
2.0
1.8
9.6 2.0±0.1
VCEO –150 V IEBO VEB=–5V –100max µA
VEBO –5 V V(BR)CEO IC=–30mA –150min V
19.9±0.3
4.0
IC –15 A hFE VCE=–4V, IC=–10A 5000min∗ a ø3.2±0.1
IB VCE(sat) –2.5max b
–1 A IC=–10A, IB=–10mA V
PC 130(Tc=25°C) W VBE(sat) IC=–10A, IB=–10mA –3.0max V
2
4.0max
20.0min
Tj 150 °C fT VCE=–12V, IE=2A 45typ MHz
3
Tstg –55 to +150 °C COB VCB=–10V, f=1MHz 320typ pF
1.05 +0.2
-0.1 0.65 +0.2
-0.1
∗hFE Rank O(5000 to 12000), P(6500 to 20000), Y(15000 to 30000)

5.45±0.1 5.45±0.1 1.4
■Typical Switching Characteristics (Common Emitter) B C E
VCC RL IC VBB1 VBB2 IB1 IB2 ton tstg tf Weight : Approx 6.0g
(V) (Ω) (A) (V) (V) (mA) (mA) (µs) (µs) (µs) a. Type No.
–40 4 10 –10 5 –10 10 0.7typ 1.6typ 1.1typ b. Lot No.
I C – V CE Characteristics (Typical) V C E (s a t) – I B Characteristics (Typical) I C – V BE Temperature Characteristics (Typical)

–50mA
–10mA
–3mA ( V C E =–4V )
Coll ector-Emitter Saturation Voltage V C E ( s a t) ( V)
–1 5 –1.5mA –3 –15
A
m
–2
–1. 0m A
Coll ector Current I C (A)

–0.8 mA
Collector C urr ent I C ( A)
–1 0 –2 –10
I C =–15A
–0. 5mA
p)
em
mp)
I C =–10 A
p)
e Te
se
Tem
I B =–0.3mA
(Ca
I C =–5A
Cas
–5 –1 –5
ase
˚C
(
125
25˚C
˚C (C
–30
0 0 0
0 –2 –4 –6 – 0.2 –0.5 –1 –5 –10 –50 –100 –200 0 –1 –2 –3
Co l l ec tor -Em i tter Vo ltag e V C E (V) Base Curr ent I B (mA) Base-Emittor Voltage V B E (V)
h F E – I C Characteristics (Typical) h F E – I C Temperature Characteristics (Typical) θ j-a – t Characteristics

θ j - a ( ˚C/W)
(V C E =–4 V) (V C E =–4V)
50,000 50000 3
125˚C
DC Cur rent Gain h F E
DC Cur rent Gain h F E
Transient Thermal Resistance
Typ 25˚ C
1
–30˚C
10,000 10000
0.5
5,000 5000
1,000 1000 0.1

– 0. 2 –0 . 5 –1 –5 – 10 – 15 – 0.2 –0.5 –1 –5 –10 –15 1 10 100 1000 2000
Colle ctor C urre nt I C (A ) Collector Cur rent I C (A) Time t(ms)
f T – I E Characteristics (Typical) Safe Operating Area (Single Pulse) P c – T a Derating

(V C E =–12 V)
60 130
Max imum P ower Diss ipat ion P C ( W)
Cut -of f Frequen cy f T (MH Z )
100
W
ith
40
In
fin
ite
he
at
si
nk
50
20
Without Heatsink
3.5
0 0
0. 02 0. 05 0. 1 0.5 1 5 10 0 25 50 75 100 125 150
Em itte r C urre nt I E (A ) Ambient Temperature Ta(˚ C)
54 Page 56 of 125
Equivalent circuit C
2SD2560
B
Darlington ( 70 Ω )
E
Silicon NPN Triple Diffused Planar Transistor (Complement to type 2SB1647) Application : Audio, Series Regulator and General Purpose
■Absolute maximum ratings (Ta=25°C) ■Electrical Characteristics (Ta=25°C) External Dimensions MT-100(TO3P)
Symbol 2SD2560 Unit Symbol Conditions 2SD2560 Unit
µA 15.6±0.4 4.8±0.2
5.0±0.2
VCBO 150 V ICBO VCB=150V 100max
2.0
1.8
9.6 2.0±0.1
VCEO 150 V IEBO VEB=5V 100max µA
VEBO 5 V V(BR)CEO IC=30mA 150min V
19.9±0.3
4.0
IC 15 A hFE VCE=4V, IC=10A 5000min∗ a ø3.2±0.1
b
IB 1 A VCE(sat) IC=10A, IB=10mA 2.5max V
PC 130(Tc=25°C) W VBE(sat) IC=10A, IB=10mA 3.0max V
2
4.0max
20.0min
Tj 150 °C fT VCE=12V, IE=–2A 70typ MHz
3
Tstg –55to+150 °C COB VCB=10V, f=1MHz 120typ pF
1.05 +0.2
-0.1 0.65 +0.2
-0.1
∗hFE Rank O(5000 to 12000), P(6500 to 20000), Y(15000 to 30000)

5.45±0.1 5.45±0.1 1.4
■Typical Switching Characteristics (Common Emitter) B C E
VCC RL IC VBB1 VBB2 IB1 IB2 ton tstg tf Weight : Approx 6.0g
(V) (Ω) (A) (V) (V) (mA) (mA) (µs) (µs) (µs) a. Type No.
40 4 10 10 –5 10 –10 0.8typ 4.0typ 1.2typ b. Lot No.
I C – V C E Characteristics (Typical) V C E (s at ) – I B Characteristics (Typical) I C – V BE Temperature Characteristics (Typical)

10mA (V C E =4V )
Col lector- Emi tter Saturation Voltage V C E ( s a t) (V)
3mA
15 3 15
A
A
50mA
2m .5m 1. 0m A
1
0. 8m A
Coll ector Current I C (A)

Col lector Current I C (A)
10 2 10
0.5mA I C =.15A
p)
mp)
mp)
Tem
e Te
I C =.10A
e Te
ase
(Cas
5
(Cas
1 I C =.5A 5
C (C
I B =0.3mA
25˚C
˚
–30˚C
125
0 0 0
0 2 4 6 0.2 0.5 1 5 10 50 100 200 0 1 2 2.2
Co l l ec t o r-Em itter Vo ltag e V C E (V) Base Current I B (mA) Base-Emittor Vol tage V B E (V)
h FE – I C Characteristics (Typical) h F E – I C Temperature Characteristics (Typical) θ j-a – t Characteristics

θ j -a (˚ C/W)
(V C E =4V) (V C E =4V)
50000 50000 3.0
5 ˚C
12
DC Curr ent G ain h F E
DC Curr ent G ain h F E
Transient Thermal Resistance
Typ
1.0
10000 10000
˚C
25
5000 5000 0.5
˚C
–30
1000 1000
500 500 0.1

02 0 .5 1 5 10 15 02 0.5 1 5 10 15 1 10 100 1000 2000
Colle ctor Current I C (A) Collector Curr ent I C ( A) Time t(ms)
f T – I E Characteristics (Typical) Safe Operating Area (Single Pulse) P c – Ta Derating

(V C E =12V)
80 130
Max imum P ower D iss ipatio n P C (W)
C ut- of f Frequenc y f T (MH Z )
60 100
W
ith
In
fin
ite
he
40
at
si
nk
50
20
Without Heatsink
3.5
0 0
– 0. 02 – 0. 0 5 – 01 –0.5 –1 –5 –10 0 25 50 75 100 125 150
Em itter Cu rren t I E (A) Ambient Temperature Ta(˚C)
158 Page 57 of 125

Page 58 of 125
74ACT04
HEX INVERTER
■ HIGH SPEED: tPD = 5.0ns (TYP.) at VCC = 5V

■ LOW POWER DISSIPATION:
ICC = 2µA(MAX.) at TA=25°C
■ COMPATIBLE WITH TTL OUTPUTS
VIH = 2V (MIN.), V IL = 0.8V (MAX.)
■ 50Ω TRANSMISSION LINE DRIVING
CAPABILITY DIP SOP TSSOP
■ SYMMETRICAL OUTPUT IMPEDANCE:
|IOH| = IOL = 24mA (MIN)
■ BALANCED PROPAGATION DELAYS: ORDER CODES
tPLH ≅ tPHL PACKAGE TUBE T&R
■ OPERATING VOLTAGE RANGE:
DIP 74ACT04B
VCC (OPR) = 4.5V to 5.5V
SOP 74ACT04M 74ACT04MTR
■ PIN AND FUNCTION COMPATIBLE WITH
74 SERIES 04 TSSOP 74ACT04TTR
■ IMPROVED LATCH-UP IMMUNITY
The device is designed to interface directly High
DESCRIPTION Speed CMOS systems with TTL, NMOS and
The 74ACT04 is an advanced high-speed CMOS CMOS output voltage levels.
HEX INVERTER fabricated with sub-micron All inputs and outputs are equipped with
silicon gate and double-layer metal wiring C2MOS protection circuits against static discharge, giving
technology. them 2KV ESD immunity and transient excess
The internal circuit is composed of 3 stages voltage.
including buffer output, which enables high noise
immunity and stable output.
PIN CONNECTION AND IEC LOGIC SYMBOLS
July 2001 1/8
Page 59 of 125
74LCX32
LOW VOLTAGE CMOS QUAD 2-INPUT OR GATE
WITH 5V TOLERANT INPUTS
■ 5V TOLERANT INPUTS
■ HIGH SPEED:
tPD = 5.2ns (MAX.) at VCC = 3V
■ POWER DOWN PROTECTION ON INPUTS
AND OUTPUTS
■ SYMMETRICAL OUTPUT IMPEDANCE:
|IOH| = IOL = 24mA (MIN) at VCC = 3V SOP TSSOP
■ PCI BUS LEVELS GUARANTEED AT 24 mA
■ BALANCED PROPAGATION DELAYS: Table 1: Order Codes
tPLH ≅ tPHL
■ OPERATING VOLTAGE RANGE: PACKAGE T&R
VCC(OPR) = 2.0V to 3.6V (1.5V Data
SOP 74LCX32MTR
Retention)
TSSOP 74LCX32TTR
■ PIN AND FUNCTION COMPATIBLE WITH
74 SERIES 32
■ LATCH-UP PERFORMANCE EXCEEDS technology. It is ideal for low power and high
500mA (JESD 17) speed 3.3V applications; it can be interfaced to 5V
■ ESD PERFORMANCE: signal environment for inputs.
HBM > 2000V (MIL STD 883 method 3015); It has same speed performance at 3.3V than 5V
MM > 200V AC/ACT family, combined with a lower power
consumption.
DESCRIPTION All inputs and outputs are equipped with
The 74LCX32 is a low voltage CMOS QUAD protection circuits against static discharge, giving
2-INPUT OR GATE fabricated with sub-micron them 2KV ESD immunity and transient excess
silicon gate and double-layer metal wiring C2MOS voltage.
Figure 1: Pin Connection And IEC Logic Symbols
Rev. 6
September 2004 1/11
Page 60 of 125
A3S56D30ETP
A3S56D40ETP
256M Double Data Rate Synchronous DRAM
Pin Assignment (Top View) 66-pin TSOP

x8
x16
VDD VDD 1 66 VSS VSS
DQ0 DQ0 2 65 DQ15 DQ7
VDDQ VDDQ 3 64 VSSQ VSSQ
NC DQ1 4 63 DQ14 NC
DQ1 DQ2 5 62 DQ13 DQ6
VSSQ VSSQ 6 61 VDDQ VDDQ
NC DQ3 7 66pin TSOP(II) 60 DQ12 NC
DQ2 DQ4 8 59 DQ11 DQ5
VDDQ VDDQ 9 58 VSSQ VSSQ
NC DQ5 10 57 DQ10 NC
DQ3 DQ6 11 56 DQ9 DQ4
VSSQ VSSQ 12 55 VDDQ VDDQ
NC DQ7 13 400mil width 54 DQ8 NC
NC NC 14 53 NC NC
VDDQ VDDQ 15
x 52 VSSQ VSSQ
NC LDQS 16 875mil length 51 UDQS DQS
NC NC 17 50 NC NC
VDD VDD 18 49 VREF VREF
NC NC 19 48 VSS VSS
NC LDM 20 0.65mm 47 UDM DM
/WE /WE 21 Lead Pitch 46 /CLK /CLK
/CAS /CAS 22 45 CLK CLK
/RAS /RAS 23 44 CKE CKE
/CS /CS 24 43 NC NC
NC NC 25 Row 42 A12 A12
BA0 BA0 26 41 A11 A11
A0-12
BA1 BA1 27 40 A9 A9
A10/AP A10/AP 28 Column 39 A8 A8
A0 A0 29 38 A7 A7
30
A0-9 (x8) 37 A6 A6
A1 A1
A2 A2 31 A0-8 (x16) 36 A5 A5
A3 A3 32 35 A4 A4
VDD VDD 33 34 VSS VSS
CLK, /CLK : Master Clock A0-12 : Address Input

CKE : Clock Enable BA0,1 : Bank Address Input
/CS : Chip Select Vdd : Power Supply
/RAS : Row Address Strobe VddQ : Power Supply for Output
/CAS : Column Address Strobe Vss : Ground
/WE : Write Enable VssQ : Ground for Output
DQ0-15 : Data I/O (x16)
DQ0-7 : Data I/O (x8)
UDM, LDM : Write Mask (x16)
DM : Write Mask (x8)
UDQS, LDQS : Data Strobe (x16)
DQS : Data Strobe (x8)
Revision 1.9 Page 61 of 125 3

Page 62 of 125
CS42528
2. PIN DESCRIPTIONS
SAI_SDOUT
CX_SDOUT
CX_SDIN2
CX_SDIN3
CX_SDIN4
SAI_LRCK
SAI_SCLK
ADCIN1
ADCIN2
OMCK
RMCK
DGND
RXP0
TXP
VLS
VD
64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49
CX_SDIN1 1 48 RXP1/G PO 1
CX_SCLK 2 47 RXP2/G PO 2
CX_LRCK 3 46 RXP3/G PO 3
VD 4 45 RXP4/G PO 4
DGND 5 44 RXP5/G PO 5
VLC 6 43 RXP6/G PO 6
SCL/CCLK 7 42 RXP7/G PO 7
SDA/CDO UT 8 CS42528 41 VARX
AD1/CDIN 9 40 AG ND
AD0/CS 10 39 LPFLT
INT 11 38 MUTEC
RST 12 37 AO UTA1-
AINR- 13 36 AOUTA1+
AINR+ 14 35 AOUTB1+
AINL+ 15 34 AO UTB1-
AINL- 16 33 AO UTA2-
17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
AOUTA4-
AOUTB2-
FILT+
AOUTB4+
AOUTA4+
AOUTB4-
AOUTB3-
AOUTA3-
AOUTB3+
AOUTA3+
AOUTB2+
AOUTA2+
VA
VQ
REFGND
AGND
Pin Name # Pin Description

CX_SDIN1 1 Codec Serial Audio Data Input (Input) - Input for two’s complement serial audio data.
CX_SDIN2 64
CX_SDIN3 63
CX_SDIN4 62
CX_SCLK 2 CODEC Serial Clock (Input/Output) - Serial clock for the CODEC serial audio interface.
CX_LRCK 3 CODEC Left Right Clock (Input/Output) - Determines which channel, Left or Right, is currently active on
the CODEC serial audio data line.
VD 4 Digital Power (Input) - Positive power supply for the digital section.
51
DGND 5 Digital Ground (Input) - Ground reference. Should be connected to digital ground.
52
VLC 6 Control Port Power (Input) - Determines the required signal level for the control port.
SCL/CCLK 7 Serial Control Port Clock (Input) - Serial clock for the serial control port. Requires an external pull-up
resistor to the logic interface voltage in I2C mode as shown in the Typical Connection Diagram.
SDA/CDOUT 8 Serial Control Data (Input/Output) - SDA is a data I/O line in I2C mode and requires an external pull-up
resistor to the logic interface voltage, as shown in the Typical Connection Diagram. CDOUT is the output
data line for the control port interface in SPI mode.
AD1/CDIN 9 Address Bit 1 (I2C)/Serial Control Data (SPI) (Input) - AD1 is a chip address pin in I2C mode; CDIN is
the input data line for the control port interface in SPI mode.
DS586PP5 17
Page 63 of 125
Page 64 of 125
EE SS II
Excel Semiconductor inc.
CONNECTION DIAGRAM
A15 1 48 A16
A14 2 47 BYTE#
A13 3 46 Vss
A12 4 45 DQ15/A-1
A11 5 44 DQ7
A10 6 48-Pin Standard TSOP 43 DQ14
A9 7 42 DQ6
A8 8 41 DQ13
A19 9 40 DQ5
A20 10 39 DQ12
WE# 11 38 DQ4
RESET# 12 37 Vcc
NC 13 ES29LV320E 36 DQ11
WP#/ACC 14 35 DQ3
RY/BY# 15 34 DQ10
A18 16 33 DQ2
A17 17 32 DQ9
A7 18 31 DQ1
A6 19 30 DQ8
A5 20 29 DQ0
A4 21 28 OE#
A3 22 27 Vss
A2 23 26 CE#
A1 24 25 A0
48-Ball FBGA 6 x 8 mm)

(Top View, Balls Facing Down)
C D E F G H J K
7 A13 A12 A14 A15 A16 BYTE# DQ15/ Vss

A-1
6 A9 A8 A10 A11 DQ7 DQ14 DQ13 DQ6
5 WE# RESET# NC A19 DQ5 DQ12 Vcc DQ4
4 RY/ WP#/ A18 A20 DQ2 DQ10 DQ11 DQ3

BY# ACC
3 A7 A17 A6 A5 DQ0 DQ8 DQ9 DQ1
2 A3 A4 A2 A1 A0 CE# OE# Vss
5 Rev. 0A May 25, 2006

ES29LV320E
Page 65 of 125
Page 66 of 125
Page 67 of 125
Page 68 of 125
Page 69 of 125
SEMICONDUCTOR KIA278R05PI~KIA278R15PI
TECHNICAL DATA BIPOLAR LINEAR INTEGRATED CIRCUIT
4 TERMINAL 2A OUTPUT LOW DROP

VOLTAGE REGULATOR
A C DIM MILLIMETERS
A 10.00 +_ 0.20
The KIA278Rᴧᴧ Series are Low Drop Voltage Regulator B _ 0.20
15.00 +
_ 0.20
F
C 2.70 +
suitable for various electronic equipments. E
O
D 0.60 +_ 0.10
Φ3.20 + _ 0.20
It provides constant voltage power source with TO-220 4 terminal E
B
F _
3.50 + 0.10
lead full molded PKG. The Regulator has multi function such as G _
15.70 + 0.20
G
H _ 0.10
0.40 +
over current protection, overheat protection and ON/OFF control. S R J 14.3+0.2/-0.1
L V V L K 1.45 +_ 0.10
K L _ 0.10
1.00 +
T U
FEATURES H M 2.54
_ 0.20
N 4.50 +
J
ᴌ2.0A Output Low Drop Voltage Regulator. D O 7.5+_ 0.1
P _ 0.10
1.50 +
ᴌBuilt in ON/OFF Control Terminal. R 5
ᴌBuilt in Over Current Protection, Over Heat M
S 8
T _ 0.1
1.30 +
Protection Function. U _ 0.1
3-1.00 +
V _ 0.1
1.30 +
N
P 1 DC INPUT (V IN )
2 DC OUTPUT (VO )
1 2 3 4
3 GND
4 ON/OFF CONTROL
LINE UP
ITEM OUTPUT VOLTAGE (Typ.) UNIT
TO-220IS-4
KIA278R05PI 5
KIA278R06PI 6
KIA278R08PI 8
KIA278R09PI 9 V
KIA278R10PI 10
KIA278R12PI 12
* KIA278R15PI 15
* Note) * : Under Development.
MAXIMUM RATING (Ta=25ᴱ)

CHARACTERISTIC SYMBOL RATING UNIT Remark
Input Voltage VIN 35 V -
ON/OFF Control Voltage VC 35 V -
Output Current IO 2 A -
Power Dissipation 1 Pd1 1.5 W No heatsink
Power Dissipation 2 Pd2 15 W with heatsink
Junction Temperature Tj 125 ᴱ -
Operating Temperature Topr -20ᴕ80 ᴱ -
Storage Temperature Tstg -30ᴕ125 ᴱ -
Soldering Temperature (10sec) Tsol 260 ᴱ -
2001. 6. 28 Revision No : 3 1/7
Page 70 of 125
SEMICONDUCTOR KIA378R05PI~KIA378R15PI
TECHNICAL DATA BIPOLAR LINEAR INTEGRATED CIRCUIT
4 TERMINAL 3A OUTPUT LOW DROP

VOLTAGE REGULATOR
A C DIM MILLIMETERS
A 10.00 +_ 0.20
The KIA378R Series are Low Drop Voltage B _ 0.20
15.00 +
F
C _ 0.20
2.70 +
Regulator suitable for various electronic equipments. E
O
D _ 0.10
0.60 +
E Φ3.20 + _ 0.20
It provides constant voltage power source with TO-220IS-4
B
F _
3.50 + 0.10
_ 0.20
terminal lead full molded PKG. G 15.70 +
G
H _ 0.10
0.40 +
The Regulator has multi-function such as over current S R J 14.3+0.2/-0.1
L V V L K _ 0.10
1.45 +
protection, overheat protection and ON/OFF control. K L _ 0.10
1.00 +
T U
H M 2.54
N _ 0.20
4.50 +
J
FEATURES D O 7.5+_ 0.1
P _ 0.10
1.50 +
3.0A Output Low Drop Voltage Regulator. R 5
Built in ON/OFF Control Terminal. M
S 8
T _ 0.1
1.30 +
Built in Over Current Protection, Over Heat U _ 0.1
3-1.00 +
V _ 0.1
1.30 +
Protection Function.
N
P 1 DC INPUT (V IN )
2 DC OUTPUT (VO )
1 2 3 4
3 GND
4 ON/OFF CONTROL
LINE UP
ITEM OUTPUT VOLTAGE (Typ.) UNIT TO-220IS-4
KIA378R05PI 5
KIA378R06PI 6
KIA378R08PI 8
KIA378R09PI 9 V
KIA378R10PI 10
KIA378R12PI 12
KIA378R15PI 15
MAXIMUM RATINGS (Ta=25 )

CHARACTERISTIC SYMBOL RATING UNIT Remark
Input Voltage VIN 35 V -
ON/OFF Control Voltage VC 35 V -
Output Current IO 3 A -
Power Dissipation 1 Pd1 1.5 W No heatsink
Power Dissipation 2 Pd2 15 W with heatsink
Junction Temperature Tj -40 150 -
Operating Temperature Topr -30 85 -
Storage Temperature Tstg -40 150 -
Soldering Temperature (10sec) Tsol 260 -
2005. 2. 1 Revision No : 3 1/7
Page 71 of 125
Page 72 of 125
Page 73 of 125
Page 74 of 125
Page 75 of 125
Page 76 of 125
Page 77 of 125
LC72723, LC72723M
Pin Assignment (DIP16/MFP16)
Block Diagram
No. 6037-2/8
Page 78 of 125
ESMT M12L16161A
SDRAM 512K x 16Bit x 2Banks

Synchronous DRAM
FEATURES GENERAL DESCRIPTION
z JEDEC standard 3.3V power supply The M12L16161A is 16,777,216 bits synchronous high
z LVTTL compatible with multiplexed address data rate Dynamic RAM organized as 2 x 524,288 words by
z Dual banks operation 16 bits, fabricated with high performance CMOS technology.
z MRS cycle with address key programs Synchronous design allows precise cycle control with the
- CAS Latency (2 & 3 ) use of system clock I/O transactions are possible on every
- Burst Length (1, 2, 4, 8 & full page) clock cycle. Range of operating frequencies, programmable
- Burst Type (Sequential & Interleave) burst length and programmable latencies allow the same
z All inputs are sampled at the positive going edge of the device to be useful for a variety of high bandwidth, high
system clock performance memory system applications.
z Burst Read Single-bit Write operation
z DQM for masking ORDERING INFORMATION
z Auto & self refresh
z 32ms refresh period (2K cycle)
Part NO. MAX Freq. PACKAGE COMMENTS
M12L16161A-5TG 200MHz TSOP(II) Pb-free
M12L16161A-7TG 143MHz TSOP(II) Pb-free
M12L16161A-7BG 143MHz VFBGA Pb-free
PIN CONFIGURATION (TOP VIEW)

1 2 3 4 5 6 7
VDD 1 50 VSS A VSS DQ15 DQ0 VDD
DQ0 2 49 DQ15
B
DQ1 3 48 DQ14 DQ14 VSSQ VDDQ DQ1
VSSQ 4 47 VSSQ
C DQ13 VDDQ VSSQ DQ2
DQ2 5 46 DQ13
DQ3 6 45 DQ12 D DQ12 DQ11 DQ4 DQ3
VDDQ 7 44 VDDQ
DQ4 8 43 DQ11 E DQ10 VSSQ VDDQ DQ5
DQ5 9 42 DQ10
F DQ9 VDDQ VSSQ DQ6
VSSQ 10 41 VSSQ
DQ6 11 40 DQ9
G DQ8 NC NC DQ7
DQ7 12 39 DQ8
VDDQ 13 38 VDDQ H NC NC NC NC
LDQM 14 37 N.C/RFU
NC UDQM LDQM WE
WE 15 36 UDQM J
CAS 16 35 CLK
K NC CLK RAS CAS
RAS 17 34 CKE
CS 18 33 N.C L CKE NC NC CS
BA 19 32 A9
A10/AP 20 31 A8 M A11 A9 NC NC
A0 21 30 A7
N A8 A7 A0 A10
A1 22 29 A6
A2 23 28 A5
P A6 A5 A2 A1
A3 24 27 A4 50PIN TSOP(II)
VDD 25 26 VSS (400mil x 825mil) VSS A4 A3 VDD
60 Ball VFBGA
R (6.4x10.1mm)
(0.8 mm PIN PITCH) (0.65mm ball pitch)
Elite Semiconductor Memory Technology Inc. Publication Date : May. 2005

Revision : 2.4 2/30
Page 79 of 125
M24C64, M24C32
SUMMARY DESCRIPTION
These I2C-compatible electrically erasable pro- Table 2. Signal Names
grammable memory (EEPROM) devices are orga-
nized as 8192 x 8 bits (M24C64) and 4096 x 8 bits E0, E1, E2 Chip Enable
(M24C32).
SDA Serial Data
Figure 2. Logic Diagram SCL Serial Clock
VCC WC Write Control
VCC Supply Voltage
VSS Ground
3
Power On Reset: VCC Lock-Out Write Protect
E0-E2 SDA
In order to prevent data corruption and inadvertent
M24C64 Write operations during Power-up, a Power On
SCL M24C32 Reset (POR) circuit is included. At Power-up, the
internal reset is held active until VCC has reached
WC the Power On Reset (POR) threshold voltage, and
all operations are disabled – the device will not re-
spond to any command. In the same way, when
VCC drops from the operating voltage, below the
Power On Reset (POR) threshold voltage, all op-
VSS erations are disabled and the device will not re-
AI01844B spond to any command.
A stable and valid VCC (as defined in Table 9. and
Table 10.) must be applied before applying any
I2C uses a two-wire serial interface, comprising a logic signal.
bi-directional data line and a clock line. The devic-
es carry a built-in 4-bit Device Type Identifier code Figure 3. DIP, SO, TSSOP and UFDFPN
(1010) in accordance with the I2C bus definition.
Connections
The device behaves as a slave in the I2C protocol,
with all memory operations synchronized by the
serial clock. Read and Write operations are initiat-
ed by a Start condition, generated by the bus mas- M24C64
ter. The Start condition is followed by a Device M24C32
Select Code and Read/Write bit (RW) (as de-
scribed in Table 3.), terminated by an acknowl- E0 1 8 VCC
edge bit. E1 2 7 WC
When writing data to the memory, the device in- E2 3 6 SCL
serts an acknowledge bit during the 9th bit time, VSS 4 5 SDA
following the bus master’s 8-bit transmission.
AI01845C
When data is read by the bus master, the bus
master acknowledges the receipt of the data byte
in the same way. Data transfers are terminated by
a Stop condition after an Ack for Write, and after a
NoAck for Read.
Note: See PACKAGE MECHANICAL section for package dimen-
sions, and how to identify pin-1.
4/26
Page 80 of 125
Page 81 of 125
Page 82 of 125
Page 83 of 125
NJM2391
LOW DROPOUT VOLTAGE REGULATOR

GENERAL DESCRIPTION PACKAGE OUTLINE
The NJM2391 is low dropout voltage regulators
featuring high precision voltage.
It is suitable for Notebook PCs, PC cards and hard
disks where 3.3V need to be generated from 5V supply. NJM2391DL1
A small TO-252 package is adopted for the space
saving.
FEATURES
zOutput Current Io(max.)=1A
zHigh Precision Output Voltage Vo±1%
zLow Dropout Voltage ∆ VI-O =1.1V typ. At Io=1A
zInternal Excessive Voltage Protection Circuit
zInternal Short Circuit Current Limit
zInternal Thermal Overload Protection
zBipolar Technology
zPackage Outline TO-252
PIN CONFIGURATION
2
PIN FUNCTION
1.VIN
2.GND
3.VOUT
1 3
NJM2391DL1
ABSOLUTE MAXIMUM RATINGS (Ta=25°C)

PARAMETER SYMBOL RATINGS UNIT
Input Voltage V+ +10 V
8 (Tc=25°C)
Power Dissipation PD TO-252 W
0.8(Ta≤25°C)
Operating Temperature Topr −40 ~ +85 °C
Storage Temperature Tstg −50 ~ +125 °C
OUTPUT VOLTAGE RANK LIST

Device Name VOUT
NJM2391DL1-25 2.5V
NJM2391DL1-26 2.6V
NJM2391DL1-28 2.85V
NJM2391DL1-03 3.0V
NJM2391DL1-33 3.3V
NJM2391DL1-35 3.5V
NJM2391DL1-05 5.0V
Page 84 of 125
NJM2595
5-INPUT 3-OUTPUT VIDEO SWITCH
■ GENERAL DESCRIPTION ■ PACKAGE OUTLINE
The NJM2595 is a 5-input 3-output video switch. Its switches

select one from five signals received from VTR,TV,DVD,
TV-GAME and others.
The NJM2595 is designed for audio items, such as AV amplifier
and others.
NJM2595D NJM2595M
■ FEATURES
● 5-input 3-output
● Operating Voltage ±4.0 to ±6.5V
● Operating current ±15mAtyp. at Vcc=±5V
● Crosstalk -65dBtyp.
● Internal 6dB Amplifier
● Internal 75Ω Driver
● Bipolar Technology
● Package Outline DIP16,DMP16
■ PIN CONFIGURATION and BLOCK DIAGRAM
+
V SW2 SW1 SW5
16 10 14 2
Vin1 13
S1 S5
Vin2 9 75Ω
20k
6dB
Amp Driver 1 Vout1
20k
S2
Vin3 7
20k S4 S6
75Ω
Vin4 5
6dB
Amp Driver 15 Vout2
20k S3 20k
Vin5 3
20k S7
6dB 75Ω
Amp Driver 11 Vout3
20k
4 6 12 8
SW3 SW4 GND V-
-1-
Page 85 of 125
NJM2845/46
LOW DROPOUT VOLTAGE REGULATOR
GENERAL DESCRIPTION PACKAGE OUTLINE

The NJM2845 is low dropout voltage regulator. Advanced
Bipolar technology achieves low noise, high ripple rejection
and low quiescent current.
NJM2845 is 3 terminal type and NJM2846 is ON/OFF control NJM2845DL1 NJM2846DL3
built in type. These product can be selected according to the
applications.
FEATURES
High Ripple Rejection 75dB typ. (f=1kHz,3V Version)
Output Noise Voltage Vno=45µVrms typ. (Vo=3V Version)
Output capacitor with 2.2µF ceramic capacitor (Vo≥2.6V)
Output Current Io(max.)=800mA
High Precision Output Vo ±1.0%
Low Dropout Voltage 0.18V typ. (Io=500mA)
ON/OFF Control (NJM2846)
Internal Short Circuit Current Limit
Internal Thermal Overload Protection
Bipolar Technology
Package Outline TO-252-3 (NJM2845DL1), TO-252-5 (NJM2846DL3)
PIN CONFIGURATION
2 3
1.VIN 1.CONTROL
2.GND 2.VIN
3.VOUT 3.GND
4.Vo
1 3 5.NC
123 45
NJM2845DL1 NJM2846DL3
EQUIVALENT CIRCUIT
V IN V OUT VIN VOUT
Thermal Control Thermal

Protection Protection
Bandgap Bandgap
Reference Reference
GND GND
NJM2845DL1 NJM2846DL3
Ver.2005-01-20 -1-
Page 86 of 125
Page 87 of 125
NJW1197C
PIN FUNCTION 80 51
81 50
100 31
1 30
No. SYMBOL FUNCTION No. SYMBOL FUNCTION
1 ROUT Rch output 51 DCR_IN “Multi-channel selector” Rch input
2 COUT Cch output 52 DCR_OUT “Input selector” Rch output
3 LSOUT LSch output 53 GND Ground
4 RSOUT RSch output 54 DCL_IN “Multi-channel selector” Lch input
5 LBOUT LBch output 55 DCL_OUT “Input selector” Lch output
6 RBOUT RBch output 56 GND Ground
7 SWOUT SWch output 57 REC_B1R “Input selector” Rch REC output B1
8 GND Ground 58 REC_B1L “Input selector” Lch REC output B1
9 FIL_BL2 Lch Bass filter terminal 2 59 REC_A4R “Input selector” Rch REC output A4
10 FIL_BL1 Lch Bass filter terminal 1 60 REC_A4L “Input selector” Lch REC output A4
11 FIL_TL Lch Treble filter terminal 61 REC_A3R “Input selector” Rch REC output A3
12 TCAP Switching noise rejection capacitor 62 REC_A3L “Input selector” Lch REC output A3
13 FIL_BR2 Rch Bass filter terminal 2 63 REC_A2R “Input selector” Rch REC output A2
14 FIL_BR1 Rch Bass filter terminal 1 64 REC_A2L “Input selector” Lch REC output A2
15 FIL_TR Rch Treble filter terminal 65 REC_A1R “Input selector” Rch REC output A1
16 V+ + Power supply voltage input 66 REC_A1L “Input selector” Lch REC output A1
17 ADR Chip address select input 67 VDDOUT Internal Digital +Power Supply Output
18 V- - Power supply voltage input 68 DATA Control data signal input
19 L1IN “Input selector” Lch input 1 69 CLOCK Clock signal input
20 DCCAP_SW Switching noise rejection capacitor 70 LATCH Latch signal input
21 R1IN “Input selector” Rch input 1 71 MUTE External mute control
22 DCCAP_RB Switching noise rejection capacitor 72 FL+ “Input selector gain control” Lch no-inverted output
23 L2IN “Input selector” Lch input 2 73 FL- “Input selector gain control” Lch inverted output
24 DCCAP_LB Switching noise rejection capacitor 74 FR+ “Input selector gain control” Rch no-inverted output
25 R2IN “Input selector” Rch input 2 75 FR- “Input selector gain control” Rch inverted output
26 DCCAP_RS Switching noise rejection capacitor 76 GND Ground
27 L3IN “Input selector” Lch input 3 77 LSCIN Multi-channel LSch input C
28 DCCAP_LS Switching noise rejection capacitor 78 RSCIN Multi-channel RSch input C
29 R3IN “Input selector” Rch input 3 79 LBCIN Multi-channel LBch input C
30 DCCAP_C Switching noise rejection capacitor 80 RBCIN Multi-channel RBch input C
31 L4IN “Input selector” Lch input 4 81 GND Ground
32 DCCAP_R Switching noise rejection capacitor 82 LAIN Multi-channel Lch input A
33 R4IN “Input selector” Rch input 4 83 RAIN Multi-channel Rch input A
34 DCCAP_L Switching noise rejection capacitor 84 CAIN Multi-channel Cch input A
35 L5IN “Input selector” Lch input 5 85 LSAIN Multi-channel LSch input A
36 GND Ground 86 RSAIN Multi-channel RSch input A
37 R5IN “Input selector” Rch input 5 87 LBAIN Multi-channel LBch input A
38 GND Ground 88 RBAIN Multi-channel RBch input A
39 L6IN “Input selector” Lch input 6 89 SWAIN Multi-channel SWch input A
40 L9IN “Input selector” Lch input 9 90 GND Ground
41 R6IN “Input selector” Rch input 6 91 LBIN Multi-channel Lch input B
42 R9IN “Input selector” Rch input 9 92 RBIN Multi-channel Rch input B
43 L7IN “Input selector” Lch input 7 93 CBIN Multi-channel Cch input B
44 L10IN “Input selector” Lch input 10 94 LSBIN Multi-channel LSch input B
45 R7IN “Input selector” Rch input 7 95 RSBIN Multi-channel RSch input B
46 R10IN “Input selector” Rch input 10 96 LBBIN Multi-channel LBch input B
47 L8IN “Input selector” Lch input 8 97 RBBIN Multi-channel RBch input B
48 L11IN “Input selector” Lch input 11 98 SWBIN Multi-channel SWch input B
49 R8IN “Input selector” Rch input 8 99 GND Ground
50 R11IN “Input selector” Rch input 11 100 LOUT Lch output
–2–
Page 88 of 125
R×5VT
PIN CONFIGURATION
• TO-92 • SOT-89 • SOT-23-5
5 4
(mark side)
(mark side) (mark side)
1 2 3 1 2 3
1 2 3
PIN DESCRIPTION
• TO-92 • SOT-89 • SOT-23-5
Pin No. Symbol Pin No. Symbol Pin No. Symbol
1 OUT 1 OUT 1 OUT
2 VDD 2 VDD 2 VDD
3 GND 3 GND 3 GND
4 NC
5 NC
Page 89 of 125
Page 90 of 125
ST232
PIN CONFIGURATION
PIN DESCRIPTION
PIN No SYMBOL NAME AND F UNCTION
1 C1+ Positive Terminal for the first Charge Pump Capacitor
2 V+ Doubled Voltage Terminal
3 C1- Negative Terminal for the first Charge Pump Capacitor
4 C2+ Positive Terminal for the second Charge Pump Capacitor
5 C2- Negative Terminal for the second Charge Pump Capacitor
6 V- Inverted Voltage Terminal
7 T2OUT Second Transmitter Output Voltage
8 R2IN Second Receiver Input Voltage
9 R2OUT Second Receiver Output Voltage
10 T2IN Second Transmitter Input Voltage
11 T1IN First Transmitter Input Voltage
12 R1OUT First Receiver Output Voltage
13 R1IN First Receiver Input Voltage
14 T1OUT First Transmitter Output Voltage
15 GND Ground
16 VCC Supply Voltage
ABSOLUTE MAXIMUM RATINGS (Note 1)

Symbol Parameter Value Unit
VCC Supply Voltage -0.3 to 6 V
TIN Transmitter Input Voltage Range -0.3 to (VCC + 0.3) V
RIN Receiver Input Voltage Range ±30 V
TOUT Transmitter Output Voltage Range (V+ + 0.3) to (V- - 0.3) V
R OUT Receiver Output Voltage Range -0.3 to (VCC + 0.3) V
TSCTOUT Short Circuit Duration on TOUT infinite
o
Tstg Storage Temperature Range -65 to +150 C
Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these condition is not implied.
Note1: No external supply can be applied toV+ terminal and V- terminal.
2/11
Page 91 of 125
Page 92 of 125
Page 93 of 125
Page 94 of 125
Page 95 of 125
Page 96 of 125
Page 97 of 125
Page 98 of 125
Page 99 of 125
Page 100 of 125

Page 101 of 125

Page 102 of 125

Page 103 of 125

Page 104 of 125

Page 105 of 125

Page 106 of 125


Page 108 of 125

6 5 4 3 2 1
AVR254/255/354/355 BLOCK DIAGRAM

RT
LT
MIC_AMP
HP_IN
ALL version A-BUS OUT 6dB AMP +8dB MIC SIG. +40dB
AVR355 OPTION NJW1159
PRE-OUT
has TUNER module. 2CH MAIN AMP HP_AMP
VOL
PRE AMP +12V
TO FUNCTION SEL MULTI_OUT P-AMP
H_PHONE OUT
- FRONT L +29dB
TUNER L/R AVR354&355 OPTION or MIC_INPUT
+
TONE
TUNER MULTI_MUTE * 2EA FRONT L P-AMP
FRONT R +29dB
D MODULE TUNER CONT
FL/R
D
PRE AMP
1
+
6/8 CHANNEL INPUT
- P-AMP -
FL
SL/R + SBL/MULTI L +29dB
2
ATT
TONE
3
+
SBL/R FRONT R
4
- FR
P-AMP
SBR/MULTI R +29dB
PRE AMP 5
+
CEN/SUB
-
SBL/ZONE2 LEFT
- 6
DATA CLOCK +
P-AMP
SURR L +29dB
7
+
-
SBR/ZONE2 RIGHT
SURR L 8
NJW1197FC2 -
PRE AMP
SURR R
P-AMP
9
ANALOG 5 IN +29dB
+ 10
ANALOG 4 IN 1
SURR R P-AMP
CEN +29dB
SL
PRE AMP DC/OVER CURRENT 2
ANALOG 4 OUT - SENS 3
+ Temp. Sensor SR
4
ANALOG 3 IN
POWER HEAT2
ANALOG AUDIO
CEN AMP
TEMP I/F 5
MUTE
PRE AMP CEN
ANALOG 2 IN 6
- P_LINE_FAIL
+ PROTECT
ANALOG 2 OUT
C SUBWOOFER TO XM PART C
ANALOG 1 IN PRE AMP
(TO VIDEO PART)
+5.3V
REGULATOR
(+5V)
M/P
- TO TORINO PART
+ TO TORINO PART REGULATOR REGULATOR
+9VDH
ANALOG FRONT IN +5V (+5V)
+9VDH
(+9V) ISSUE
+1.8V (+1.8V) (+1.8V)
SBL/MULTI L
XM IN
PRE AMP TO DSP PART
ANAM
REGULATOR
USA VER. ONLY -
+5VD MULTI. LAB
iPod IN + TO VIDEO PART (+5V)
STEREO or iPod IN +5V 2008.02.25
SBR/MULTI R REGULATOR
+12V
TO VIDEO PART (+12V)
(TO IPOD PART) TO DSP PART
HDMI_IN1 HDMI_IN2 HDMI_IN3 HDMI_OUT REGULATOR
+9V +15V
(+9V) REGULATOR
TO VIDEO PART
D_SW
D_SBR
D_SR
D_FR
D_CNT
D_SBL
D_SL
D_FL
-9V (-5V) -15V ( 15V)

HDMI MCLK
D_SW
D_SBR
D_CNT
XM_RADIO
D_SBL
SII9134
D_SR
D_FR
D_SL
D_FL
XM_DAT
MODULE
HDMI SCLK TO A-BUS PART REGULATOR

D- COAX.&OPT. FRONT
2CH DAC
XM_LRCK (HDMI TX)

AK4384
XM_DT
XM_L HDMI LRCK SII9185 +24V

ADUTA1+
ADUTB1+
ADUTA2+
ADUTB2+
ADUTA3+
ADUTB3+
ADUTB4+
ADUTA1-
ADUTB1-
ADUTA2-
ADUTB2-
ADUTA3-
ADUTB3-
ADUTB4-
24.576MHz ( 24V)
XM_BICK
(SW IC) OPT.1
D+ HDMI SD
XM_R +5VL REG
XM_MCK +5VL
I2S/DSP_SPDIF
OPT.2
XIN
XOUT
I2C & GPIO CONTROL
+VCC1 P-DOWN PWR DOWN

USA VER. ONLY OPT.3 LT AINR
CS42528 UNBAL
POWER S/W
DETECT
I2C & GPIO CONTROL
A/D, D/A CONVERTER WITH DIR +12V

-VCC1
LRCLK1
iPod L/R RT AINL

SII9135
SCLK1
SDIN1
SDIN2
SDIN3
SDIN4
MCLK
SUB TRANS
COAX.1
THE BRIDGE II
iPod IN HDMI_SPDIF
STANDBY
(HDMI RX) +VCC2
B iPod TX
I2S
UNBAL B
( iPod )
TMP86F409NG I2S COAX.2

iPod RX iPod CONT DETECT
(8BIT u-COM for iPod)
I2S -VCC2
HDMI SD
HDMI LRCK
HDMI SCLK
RST
iPod CVBS
iPod CVBS
AVR354 & 355 OPTION FLI30336 COAX OUT
ST232CDR AC OUTLET AC IN
TORINO
AUDATA0
AUDATA1
AUDATA2
AUDATA3
AVR354 & 355 OPTION ADV7342 CLKIN

LRCLK0
XMCK
SCLK0
DIGITAL VIDEO
(SCALER) MAX : 1080p
(DAC) A-BUS IR IN
THE BRIDGE II IN FROM THE BRIDGE II DIN RMCK XMCK
( iPod CVBS ) ( iPod )
SPI Serial Flash
CONTROL BY DAC
RS232C RDATA CMPDAT

CARR. OUT 8 Mbit
RBCK CMPCLK
COMPOSITE FRONT IN FROM FRONT CVBS_TORINO IN ADDRESS&DATA
DOUT RLRCK CMPREQ
S-VID Y_TORINO IN
ZONE2 IN
S-VID C_TORINO IN
DO
AVR354 & 355 OPTION OMCK DAOMCLK

Y1/2/3__TORINO IN
COMPOSITE 3 IN
THE BRIDGE II
SDRAM Cb1/2/3_TORINO IN NJM2566 I2S/DSP_SPDIF I2S
CS497004 +VKK FL FL
CONT Cr1/2/3_TORINO IN REMOTE IN
6dB
FRONT VIDEO
DSP M12L16161A
+6dB DRV
CVBS 32M
COMPOSITE 2 IN
V3 DIR CONT
I2S 16M SDRAM
REMOTE OUT
V2 FLI30336 ANALOG INPUT
COMPOSITE 2 OUT V1 +6dB DRV
DDR SDRAM ROTARY
REMOTE SENSOR
FUNC. SW CONT
256M * 2EA ENCODER

TUNER CONT
DSP MCLK
6CH VIDEO OUT (MASTER VR)
MUTE CONT
COMPOSITE 1 IN
RDS CONT
DSP CONT
VOL CONT
DIR CONT
+6dB DRV HDMI MCLK

XM CONT
COMPOSITE FRONT
NJM2595
S-VIDEO FRONT
ANALOG FRONT
PH DET
CVBS_OUT
S-VID Y_OUT DIR MCLK
FL DISPLAY
COAX.FRONT
OPT.FRONT
S-VID C_OUT
Y_OUT HDMI MCLK
Y
S-VIDEO FRONT IN FROM FRONT Cb_OUT 74VHC157
C Cr_OUT 2CH MUX
VR ENC
KEY MATRIX
COMPO COMPO COMPO MOMS SWITCH
AMBER/BLUE
FLI30336 ANALOG INPUT INPUT1 INPUT2 INPUT3

FRONT VIDEO
STANDBY
Y1
AVR354 & 355 OPTION
CONT Y Y Y KEY0~2
V3
NJM2566 ANALOG OUTPUT
+6dB DRV Y2 EEPROM (32 Kbit)
S-VID Y (BLUE)
Cb1 Cb
V2
Cb Cb REMOTE IN VOLUME Indicator
FLI30336 ANALOG INPUT Cb2 RST IC
V1
COMPOSITE MONITOR OUT TOSHIBA
Y Cr1 CARR. OUT
+6dB DRV Cr Cr Cr POWER AMP CONT
Y 16BIT u-COM
S-VIDEO 3 IN C Cr2
C MULTI_IR IN iPod Buffer IC CONT
Y3
A Y
NJM2595 S-VIDEO MONITOR OUT Cb3
Cr3
A-BUS_IR OUT
VIDEO SWITCHING CONT REVISION 2 4 6 A
S-VIDEO 2 IN
C
1 3 5 7
COMPONENT MONITOR OUT
FRONT VIDEO NJM2566 ANALOG OUTPUT

Y CONT
V3
COMP_Y_OUTPUT ** EEP_ROM **
S-VIDEO 2 OUT C +6dB DRV Y
Y V2
S-VID C
FLI30336 ANALOG INPUT
COMP_Cb_OUTPUT
Cb
FOR BACK-UP MEMORY.
SCHEMATIC DIAGRAM SHEET
KEY
REMOTE ENC
POWER DOWN
STANDBY
VR ENC
S-VIDEO 1 IN C V1
VFD CONTROL
+6dB DRV
COMP_Cr_OUTPUT
Cr 1
MODEL AVR254/255/354/355 1
RS232C
NJM2595
COMMUNICATION BETWEEN TORINO & TOSHIBA MCU ST232CDR
VIDEO SWITCHING CONTROL BY MCU UART RX/TX DESIGN CHECK APPROVE DRAWING NO
S.H.Yang W.Y.Yang G.S.Wey BLOCK DIAGRAM

08.02.25 08.02.25 08.02.25 2024BLDZ 1
1
Page 109 of 125

AVR355 WIRING.sch-1 - Wed Mar 12 14:08:13 2008
Page 110 of 125

AMPLIFIER SECTION BIAS ADJUSTMENT
Measurement condition
.No input signal or volume position is minimum.
Standard value
.Ideal current = 48mA (± 5%)
.Ideal DC Voltage = 25.92mV (± 5%)
DC EVM
CUP12026* (MAIN PCB)
+ -
CN66 CN61 CN64 CN63 CN65 CN62 CN67
VR81 VR82 VR83 VR84 VR85 VR86 VR87
DC VOLTMETER ; Connect to
CN66(SL),CN61(CEN),CN64(SR),CN63(FL),CN65(SBL(AVR254,255,354,355)),CN62(FR),CN67(SBR)
NO. Channel Adjust for Adjustment

1 Front Left 25.92mV (± 5%) CN63
2 Front Right 25.92mV (± 5%) CN62
3 Center 25.92mV (± 5%) CN61
4 Surround Left 25.92mV (± 5%) CN66
5 Surround Right 25.92mV (± 5%) CN64
6 Surround Back Left 25.92mV (± 5%) CN65
7 Surround Back Right 25.92mV (± 5%) CN67
Page 111 of 125

Page 112 of 125

Page 113 of 125

Page 114 of 125

Page 115 of 125

Page 116 of 125

AVR355 input_0208.sch-1 - Fri Feb 08 15:54:26 2008
Page 117 of 125

Page 118 of 125

Page 119 of 125

080121 AVR355 VIDEO sample.sch-1 - Sat Feb 02 16:43:21 2008
Page 120 of 125

080121 AVR355 VIDEO sample.sch-2 - Sat Feb 02 16:43:48 2008
Page 121 of 125

Page 122 of 125

Page 123 of 125

Page 124 of 125

080119 AVR255_355 FRONT_LPP.sch-1 - Sat Feb 02 16:52:21 2008
Page 125 of 125

Harman/kardon: Service Manual

Uploaded by

Harman/kardon: Service Manual

Uploaded by

harman/kardon AVR 355/230 Service Manual

harman/kardon Service Manual

ESD WARNING 2 EXPLODED VIEW AND PARTS 8

Released EU2008 harman/kardon, Inc. Rev 0, 09/2008

semiconductor "chip" components.

prevent electrostatic charge build-up or exposure of the assembly.

3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.

sufficient to damage ES devices.

chassis or circuit assembly into which the device will be installed.

Each precaution in this manual should be followed during servicing.

harman/kardon AVR 355/230 Service Manual

Audio Section FM Tuner Section

Frequency Response General

Transient Intermodulation (7 channels driven)

Depth measurement includes knobs, buttons and terminal connections.

SYMPTOM CAUSE SOLUTION

No picture or on-screen • AVR Resolution to Display • Select correct Resolution as described

Programming the Remote

POLY BAG AM LOOP ANTENNA ASS'Y BATTERY ASS'Y FM 1 POLE ANT

3 SNOW PAD (L)

6 BOX ,OUT CARTON

MANUAL SETUP GUIDE STAPLE

1 POLY BAG CPB1061W 1

2 AM LOOP ANTENNA ASS'Y CSA1A027Z 1

3 BATTERY CABR03P 6 REMOCON ASS'Y MICROPHONE ASS'Y

4 FM 1 POL ANT CSA1A018Z 1

6 PAD , COVER CPS1A676 1 5 SET AVR355/230SET 1

Downloaded from www.Manualslib.com manuals search engine

1. Removing the Top Cabinet 3. Removing the Rear Panel

4. Removing the Main PCB

2. Removing the Front Panel

Downloaded from www.Manualslib.com manuals search engine

AVR355/230 EXPLODED VIEW AVR 355/230 Service Manual

NO DESCRIPTION PARTS NO. Q,ty 38 MAIN PCB ASS'Y COP12026J 1

Downloaded from www.Manualslib.com manuals search engine

AVR355/230 Electrical Parts List

FRONT PANEL ASSY

FRONT PANEL ASSY

BOTTOM CHASSIS ASS'Y

FRONT PCB ASSY

FRONT PCB ASSY

FRONT PCB ASSY

FRONT PCB ASSY

FRONT PCB ASSY

MAIN PCB ASSY

MAIN PCB ASSY

MAIN PCB ASSY

MAIN PCB ASSY

MAIN PCB ASSY

MAIN PCB ASSY

MAIN PCB ASSY

MAIN PCB ASSY

MAIN PCB ASSY

MAIN PCB ASSY

MAIN PCB ASSY

MAIN PCB ASSY

POWER PCB ASSY

POWER PCB ASSY

POWER PCB ASSY

POWER PCB ASSY

POWER PCB ASSY

INPUT PCB ASSY

INPUT PCB ASSY

INPUT PCB ASSY

INPUT PCB ASSY

INPUT PCB ASSY

INPUT PCB ASSY

INPUT PCB ASSY

INPUT PCB ASSY

INPUT PCB ASSY

INPUT PCB ASSY

INPUT PCB ASSY

INPUT PCB ASSY

VIDEO PCB ASSY

VIDEO PCB ASSY

VIDEO PCB ASSY

ABSOLUTE MAXIMUM RATINGS (Ta=25°C)

OUTPUT VOLTAGE RANK LIST