Scribd Logo
Upload

Welcome to Scribd!

  • 109 views

    Bore Pile Design Bs 8004

    Uploaded by

    Nabil Yassar
    1. This document provides design details for a bore pile, including general data, soil data, and calculations of pile bearing capacity according to material properties, soil data, and standard penetration test results. 2. Soil data includes soil types and properties at different depths, with sand and clay layers identified. 3. Three methods of calculation were used to determine the pile bearing capacity, with the minimum value of 1000 tons selected as the design capacity.

    Copyright:

    © All Rights Reserved
    Download as XLS, PDF, TXT or read online from Scribd

    Bore Pile Design Bs 8004

    Uploaded by

    Nabil Yassar
    109 views2 pages
    1. This document provides design details for a bore pile, including general data, soil data, and calculations of pile bearing capacity according to material properties, soil data, and standard penetration test results. 2. Soil data includes soil types and properties at different depths, with sand and clay layers identified. 3. Three methods of calculation were used to determine the pile bearing capacity, with the minimum value of 1000 tons selected as the design capacity.

    Original Description:

    bore pile

    Original Title

    bore pile design bs 8004

    Copyright

    © © All Rights Reserved

    Available Formats

    XLS, PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    1. This document provides design details for a bore pile, including general data, soil data, and calculations of pile bearing capacity according to material properties, soil data, and standard penetration test results. 2. Soil data includes soil types and properties at different depths, with sand and clay layers identified. 3. Three methods of calculation were used to determine the pile bearing capacity, with the minimum value of 1000 tons selected as the design capacity.

    Copyright:

    © All Rights Reserved
    Download as XLS, PDF, TXT or read online from Scribd
    Download as xls, pdf, or txt
    109 views2 pages

    Bore Pile Design Bs 8004

    Uploaded by

    Nabil Yassar
    1. This document provides design details for a bore pile, including general data, soil data, and calculations of pile bearing capacity according to material properties, soil data, and standard penetration test results. 2. Soil data includes soil types and properties at different depths, with sand and clay layers identified. 3. Three methods of calculation were used to determine the pile bearing capacity, with the minimum value of 1000 tons selected as the design capacity.

    Copyright:

    © All Rights Reserved
    Download as XLS, PDF, TXT or read online from Scribd
    Download as xls, pdf, or txt
    of 2

    Job No: Rev. No.

    1
    Project: Date: 4/13/2022
    Owner: Designed by:
    Item: Checked by:

    BORE PILE DESIGN

    A. GENERAL DATA
    Bottom level of pilecap: Df = 6 m
    Diameter of pile: d= 1.5 m
    Pile length: Lp = 35.0 m
    Pile length from ground level: 41.0
    Rebar diameter: f= 22 mm cm²
    Rebar number: n= 20
    B. SOIL DATA
    Underground water Hw = 10 m

    Position layer type hi g tn g dn C f SPT


    (m) (T/m3) (T/m3) (T/m2)
    ABOVE 1 clay 0.6 1.800 1.800 0.00 0.00 0
    PILECAP 2 clay 5.40 2.000 1.680 2.00 10.60 11
    2 clay 18.0 2.000 1.680 2.00 10.60 11
    3 sand 8.5 1.960 1.640 0.50 20.00 13
    5 clay 8.5 2.040 1.710 3.70 13.08 35
    3 sand
    4 sand
    BELOW 5 clay
    PILECAP
    7 sand 0 0
    8 sand 0 0
    9 sand 0 0
    10 sand 0
    11 sand
    END PILE 5 clay 0 2.040 1.710 3.700 13.083 35.000

    C. PILE BEARING CAPACITY

    Ptk = MIN(1,2,3) = 1072 T

    Chọn Ptk = 1000 T


    1. Refer to material
    Material data :
    - Concrete grade: C35 Rn = 60.00 Kg/cm2
    - Steel grade: A-III Ra = 3600 Kg/cm2

    Pile capacity Qvl= 1329 T (1)

    2. According to soil data (appendix B -TCXD 205-1998)


    Allowable pile capacity Qa = 1072 T (2)
    Qa = QS / FSs + Qp/FSp
    Ultimate pile capacity Qu = 1338 T
    Qu = uSfsili + qpAp
    With:
    fsi: skin friction
    qp: end bearing
    u: pile diameter
    Ap: pile cross section
    FSs: safety factor for skin friction
    FSp: safety factor for end bearing
    FSs = 1
    FSp = 2
    u= 4.712 m
    Ap = 1.767 m²
    + fs = Ca + s'h tgja
    Ca = C
    ja = 3j/4
    s'h = kss'v = (1-sinj)s'v
    s'v = Sgihi
    + qp = cNc + s'vNq + gdNg
    Nc ,Nq ,Ng sub to j

    layer type h gi Ci ji s'v fs fs*li


    m (T/m³) (T/m²) deg. (T/m²) (T/m²) (T/m)
    1 clay 0.6 1.8 0 0
    10.15
    2 clay 5.4 1.68 2 10.6
    2 clay 18 1.68 2 10.6 25.27 4.88 87.8
    3 sand 8.5 1.64 0.5 20 6.97 1.73 14.7
    5 clay 8.5 1.71 3.7 13.0833 32.54 8.05 68.5

    END
    PILE 1.71 3.7 13.0833 68.87
    sum 171.0
    j= 13.08 deg. 0.2283472438
    Nc Nq Ng 0.0000
    11.5 3.66 2.50
    qp = 301.22 T/m2

    3. Pile bearing capacity according to standard penetration test (TCXD 195-1997)

    Allow Bearing Capacity: Qa = 1124 Ton (3)


    Qa = 1.5NTBAp + (0.15NcLc + 0.43NsLs)W - Wp
    With:
    NTB SPT index at bottom pile
    Ns SPT index in clay soil layer
    Nc SPT index in sand soil layer
    Ls Length of pile in clay soil layer
    Lc Length of pile in sand soil layer
    Area of pile: Ap = 1.77 m2
    Parameter of pile: W= 4.71 m

    h Lc Ls Wp
    layer NTB Nc Ns NcLc NsLs
    (m) (m) (m) (T)
    1 0.6 0 0 0 0.6
    2 5.4 0 0 11 5.4
    2 18 0 0 11 18 0 198 26.083
    3 8.5 13 8.5 0 0 110.5 0 12.918
    5 8.5 0 0 35 8.5 0 297.5 11.866
    3 0 0 0 0 0 0 0 0.000
    4 0 0 0 0 0 0 0 0 0.000
    5 0 0 0 0 0 0 0 0.000
    7 0 0 0 0 0 0 0 0.000
    8 0 0 0 0 0 0 0 0.000
    9 0 0 0 0 0 0 0 0.000
    10 0 0 0 0 0 0 0 0.000
    11 0 0 0 0 0 0 0 0.000
    END
    PILE 35
    SUM 110.5 495.5 50.867

    You might also like