Multi-Code Remote Control 3089 Manual One Button

INSTR,INSTL,MC3089,1CH,TX
LINEAR P/N: 215641 A

INK: BLACK
MATERIAL: 20 LB. MEAD BOND
SIZE: 9.000" x 3.500"
SCALE: 1-1
SIDE 1 OF 2
OPERATIONAL CHECK
To check operation, move back a reasonable distance (about 50 ft.) and press the
transmitter button. Operation should be reliable at this distance but
environment and location of both the transmitter and receiver will affect the ®
range. If the transmitter is stowed well out of sight, it may be necessary to
remove it from its mounting and hold near the windshield. Try different locations
and positions. If operation is still unsatisfactory, the problem may be isolated by: INSTALLATION INSTRUCTIONS
1. Checking the door operator. If the door will not open when the wall button is
pressed, the problem is likely to be the operator. If the door will open by pressing DIGITAL TRANSMITTER MODEL 3089
the wall button, but not when the radio control button is pressed, the problem is
Congratulations! You have just purchased a MULTI-CODE Digital Transmitter,
probably in the radios.
which we believe to be the finest product of its kind on the market. With a little
2. Replacing the transmitter battery. If after performing the above operational care this transmitter should provide you with many years of excellent service.
checks, the controls still do not function, they should be returned to your dealer for Please take a moment to read the following instructions and you will find that setting
repair or replacement. your new transmitter will be quite an easy matter.
CAUTION: Any changes or modifications in intentional or unintentional
radiators which are not expressly approved by LINEAR CORPORATION could ACCESSING THE CODE SWITCH
void the user’s authority to operate this equipment. This applies to intentional
and unintentional radiators certified per part 15 of the F.C.C. rules and On the model 3089 the entire front lower half of the transmitter is removable.
regulations. Grasp the front lower half of the case near the bottom on both sides and pull
upward away from the transmitter, this will disengage the lower end. Then pull
LINEAR CORPORATION downward to remove the lower cover, this will expose both the code switch and
2055 Corte del Nogal • Carlsbad, CA 92009 battery compartment.
(760) 438-7000
Copyright © 1999 Linear Corporation 215641 A
INSTR,INSTL,MC3089,1CH,TX
LINEAR P/N: 215641 A
INK: BLACK
MATERIAL: 20 LB. MEAD BOND
SIZE: 9.000" x 3.500"
SCALE: 1-1
SIDE 2 OF 2
SELECTING A CODE TRANSMITTER INSTALLATION

You may set your transmitter to any code you desire but be sure that the code you The transmitter is completely self contained, including battery, and can be
set matches the code that has been set on your radio receiver. The digital code is operated while mounted in the car. It is supplied with a clip for attaching to the
determined by the positions of the 10 small switches numbered 1 through 10 sun visor, if desired. If the clip is used attach to the case by sliding it into the
located in the receiver and transmitter. Any combination of ON (CLOSED) or OFF recess provided on the back of the transmitter until the small dimples fit into the
(OPEN) positions can be selected by using a small screwdriver or ball point pen. holes in the clip.
(NOTE: The switches are in the “On” position when the side next to the number
is pressed in.) In setting your own personal code we strongly urge that several
coding schemes be avoided: ALL ON; ALL OFF; 2,4,6,8,10 ON; 1,3,5,7,9 ON. TRANSMITTER BATTERY REPLACEMENT
These positions are similar to our or other manufacturer’s test positions, or are Replacement battery - 9 volt NEDA 1604 (Eveready 216 or equivalent).
frequently used. Once the code has been set, check the operation and replace
the hatches.
The battery in the transmitter can be checked or changed by removing the front
lower half of the transmitter. Refer to the directions under “accessing the code
switch” for battery replacement.
TO REPLACE OR ADD A SET

A replacement or new transmitter or receiver may be purchased by specifying
1 2 3 4 5 6 7 8 9 10 the Model Number and the RF frequency designated on the identification label.
The RF frequency is set at the factory and must not be adjusted in the field. The
digital code can be matched to the companion receiver or transmitter by
OPEN following the above procedure.

Multi-Code Remote Control 3089 Manual One Button

Uploaded by

Multi-Code Remote Control 3089 Manual One Button

Uploaded by

INSTR,INSTL,MC3089,1CH,TX

LINEAR P/N: 215641 A

SELECTING A CODE TRANSMITTER INSTALLATION

TO REPLACE OR ADD A SET

You might also like