Data Sheet GST

E-MAIL: hombi@hombi.ru HTTP://GSTRU.RU HTTP://WWW.HOMBI.
RU
E-MAIL: hombi@hombi.ru HTTP://GSTRU.RU HTTP://WWW.HOMBI.RU
Digital Optical Smoke
Detector DI-9102
Secure and speedy communication through

the on board processor enables the detector
to make its own decision and sending data to
the panel within a second, resulting in greater
automation. The sensor and the panels
utilized fuzzy logic providing an almost
limitless cause and effect scenarios.
Drift compensation, to monitor for the long

term changes caused by aging, humidity,
temperature, dust, etc. constant monitoring
and self adjusting, the DI-9102 updates
Features and Benefits sensitivity base line for its sensing element.
Even when the detector raises a warning
1. Advance digital sensing technique advising that it requires cleaning, the
2. Built in 8 bit microprocessor sensitivity remains the same as the day it was
3. Algorithm maps for faster response and installed.
false alarm rejection
4. Secure and speedy communication Electronic addressing and sensitivity
5. Intelligent Drift compensation adjustment can be done through Handhold
6. Self diagnosis and history log Programming device (P-9910B), purchased
7. Electronic addressing separately and can be modified in the panel
8. Duplicated address report
9. Sensing chamber for exceptional dust Technical Specifications
proof ability and LED for 360º vision
10. Built in remote indicator output • Standard: EN54-part7
11. Unique Low profile design • Protection rating: IP 32
12. EN54 compliance • Operating voltage: 24Vdc Loop
voltage
Description • Operating Current:
The DI-9102 Digital Optical Smoke Detector is Standby current 0.6mA
the ideal device for most application due to its Alarm Current 1.8mA
excellent digital response to a wide variety of • Operating temperature: -10°C to
different type of smoke patterns. The unit +50°C
meets the sensitivity requirement of EN 54 part • Relative humidity: 95%
7, European Standard • Application: Indoor use
• Detecting range: 100 sqm elevated
Unique and pleasing with a low profile design, than 6m, 80 sqm less than 6m
unobtrusive to complement modern building • Field Programmable sensitivity:
designs. The unit incorporates an intelligent 0.10dB/m to 0.56dB/m – 3 levels
processor that provides Algorithm map, Digital • Address setting: Electronic addressing
signaling, Drift compensation, Self Diagnosis within 1 to 241, engage one address
and history log. • Visual Indicator: LED, Red ( lit steady
when alarm, flash in polling)
The integral microprocessor analyses the signal
• Material and colour: ABS, traffic-white
according to integrated algorithm of analyzing
• Wiring: 1 pair non polarized
fire, then confirms these pattern with the pre-
• Dimensions: diameter 10cm; height
programmed fire scenarios and smoke patterns
4.45cm
for a faster and safer response. By intelligent
analysis, the smoke detection sensitivity will be
automatically adjusted according to
temperature change, providing a rapid
response.

Digital Optical Smoke
Detector DI-9102
Detector Installation
Mounting Standard Base
Before installation verify the proper wiring and
The digital detector should be installed in
base are firmly mounted to prevent detector
compliance with all local codes or NFPA 72
damage before the installation. Point the
National Fire Alarm Code, NFPA 70 National
detector in the base by the mark-line and
Electrical Codes, BS 5389 and EN54. The
secure the detector in that position by
detector is mounted using our standard base
rotating it clockwise until it reaches the next
DB-01 allows easy adjustment. Suitable for
mark line.
surface mount only, mount on standard 1gang
electrical back box with a mounting hole of MARK 1
DETECTOR
45mm to 75mm spacing. BASE
Electrical
Box
60
Conduit
MARK 1
MARK 2
DETECTOR
Base
78mm
Detector
Programming
The address and sensitivity of the detector
100m m
can be programmed using GST handheld
programmer (P-9910), purchased separately.
Connect the two wires of the handheld
75 programmer to any two opposite terminals of
the detector.
60
45
DETECTOR TERMINAL
FIELD DEVICE PROGRAMMER

Wiring and Connection
Connect the wires to the required terminal
according to the wiring diagram. Detector loop Selection of compatible Control Panels
are connected on terminals 1 and 3 while for Compatible with all GST Intelligent Fire Alarm
the remote indicator output, connect the wire Panels GST 100, GST 200, GST 5000, GST
on terminals 2 and4.The cable must be fire 9000.
rated type and the size depends on the wiring Ordering Information:
distance. Minimum size gauge 1.0mm²(18 Part No Description Weight Pack
AWG). /Kg Qty per
Box
DI-9102 Digital Optical 0.110 120
Smoke Detector
with Remote
1 2
Indicator
60
DB-01 Detector Base 0.049 360
MANUFACTURED IN ACCORDANCE WITH

4 3
REMOTE INDICATOR
Note: Specifications are subject to change without notice.

Digital Intelligent Dual
Heat Detector DI-9103
Meets the sensitivity requirement of EN 54
part 5 and part 6 European Standard
Unique pleasing with a low profile design,

unobtrusive to complement modern building
designs. The unit incorporates an intelligent
processor that provides Algorithm map,
Digital signaling, Drift compensation, Self
Diagnosis and history log.

the on board processor enables the detector
to make its own decision and sending data
to the panel within a second, resulting in
greater automation. The sensor and the
panels utilized fuzzy logic providing an
almost limitless cause and effect scenarios.
Electronic addressing and sensitivity

Features and Benefits adjustments can be done through Handhold
Programming device (P-9910), purchased
Dual fixed temperature heat detector. separately, and can be modified in the panel.
Combining both fixed temperature and rate
of rise heat detection in a single sensor.
As standard the fixed temperature is set to Technical Specifications
66ºC while the rate of rise is set to 6ºC in
one minute. • Standard: EN54-part5
The rate of rise function can be switched off • Protection rating: IP 22
and the fixed temperature can be adjusted • Operating voltage: 24Vdc Loop
between 54 and 74 degrees C voltage
1. Built in 8 bit microprocessor • Operating Current:
2. Algorithm maps for false alarm Standby Current 0.8mA
rejection Alarm Current 1.4mA
3. Digital sensing • Operating temperature: -10°C to
4. Secure and speedy communication +50°C
5. Drift compensation • Sensitivity: 3 levels; I=58°C,
6. Self diagnosis and history log II=66°C, III=72°C
7. Electronic addressing • Address setting: Electronic
8. Duplicated address report addressing within 1-241, engage one
9. LED for 360º vision address
10. Built in remote indicator output • Relative humidity: 95%.
11. Unique low profile design • Application: Indoor use
12. Fixed temperature response is • Detecting range: 30 sqm for normal
adjustable via hand held area; and 20 sqm for high risk
programming tools. • Visual Indicator: twin LED, Red ( lit
13. EN54 compliance steady when alarm, flashing at
normal state)
Description • Material and colour: ABS, traffic-
white
This detector is extremely reliable for • Wiring: 1 pair non polarized
application in places where may have high • Dimensions: diameter 100mm;
dust levels or smokey environments, height 41mm without base
making a normal smoke detector unsuitable ,
for example boiler/plant room, cars parks,
kitchen, loading bays, furnace/kiln rooms.

Digital Intelligent Dual
Heat Detector DI-9103
Before installation verify the proper wiring
The digital detector should be installed in
and base are firmly mounted to prevent
detector damage before the installation.
Point the detector in the base by the mark-
Electrical Codes, BS 5389 and EN54. The
line and secure the detector in that position
detector is mounted using our standard base
by rotating it clockwise until it reaches the
DB-01 allows easy adjustment. Suitable for
next mark line.
surface mount only, mount on standard
1gang electrical back box with a mounting MARK 1
DETECTOR
hole of 45mm to 75mm spacing. BASE
Electrical
Box
60
Conduit
MARK 1
MARK 2
DETECTOR
Base
78mm
Detector
Programming
The address and sensitivity of the detector
100m m
75 programmer to any two opposite terminals
of the detector.
60
45
DETECTOR TERMINAL

according to the wiring diagram. Detector
loop are connected on terminals 1 and 3 Selection of compatible Control Panels
while for the remote indicator output, Compatible with all GST Intelligent Fire
connect the wire on terminals 2 and4.The Alarm Panels GST 100, GST 200, GST 5000,
cable must be fire rated type and the size GST 9000.
depends on the wiring distance. Minimum Ordering Information:
size gauge 1.0mm²(18 AWG). Part No Description Weight Pack
/Kg Qty per
Box
DI-9103 Digital Dual 0.090 120
1 2
Heat Detector
with Remote
60
Indicator
4 3
REMOTE INDICATOR

Intelligent Multi
Sensor I-9101
The integral microprocessor analyses the
signal according to the factors such as
signal strength and rate of increase, then
confirms these pattern with the pre-
programmed fire scenarios and smoke
patterns for a faster and safer response. By
intelligent analysis, the smoke detection
sensitivity will be automatically adjusted
according to temperature change,
providing a rapid response.

the on board processor enables the
detector to make its own decision, resulting
in greater automation. The sensor and the

Features and Benefits term changes caused by aging, humidity,
temperature, dust, etc. constant
1. Built in 8 bit microprocessor monitoring and self adjusting, the I-9101
2. Algorithm maps for faster response updates sensitivity base line for its sensing
and false alarm rejection element. Even when the detector raises a
3. Analogue sensing warning advising that it requires cleaning,
4. Secure and speedy communication the sensitivity remains the same as the day
5. Patented Linear Drift compensation it was installed.
6. Self diagnosis and history log
7. Electronic addressing Electronic addressing can be done through
8. Sensing chamber for exceptional dust Handheld Programming device (P-9910),
proof ability purchased separately.
9. Twin LED for 360º vision
10. Low profile design Technical Specifications
11. Ideal alternative to Ionization
detector • Standard: EN54-part 5, part 6 and
• Part 7
• Protection rating: IP 32
Description • Operating voltage: 24Vdc Loop
voltage
Combining all the features of the I-9102 • Operating Current:
Optical and the I-9103 Dual Heat Detectors Standby current 0.6mA
the unit provides an ideal solution for life and Alarm Current 2mA
safety systems. Ideally suitable for • Operating temperature:-10°C to
application in data processing area including +50°C
telephone exchange, conference rooms, • Relative humidity: 95%
indoor markets or shops, dining area, factory, • Application: Indoor use
recording studio and libraries etc. • Detecting range: 30 sqm for normal
Aesthetically pleasing with a low profile area; and 20 sqm for high risk
design, unobtrusive to complement modern • Programmable sensitivity: 3 levels
building designs. The unit incorporates an • Visual Indicator: twin LED, Red ( lit
intelligent processor that provides Algorithm steady when alarm, 3 sec interval
map, Built-in A/D converter, Drift blinking at normal state)
compensation, Self Diagnosis and history log. • Material and colour: ABS, off-white
5cm

Intelligent Multi
Sensor I-9101 ELECTRICAL BOX
1 GANG
CEILING
The detector is mounted using our standard MARK−LINE 2ND MARK−LINE
base DZ-03. Multiple-direction design allows

easy direction adjustment. Suitable for
surface mount only, mount on embedded box;
1gang UK standard. LED INDICATOR
ROTATE CLOCKWISE
CONCRETE PAD OR EMBEDDED BOX

HOLDING PAD
SCREW
Programming
HOLE The address of the detector and sensitivity

STANDARD DETECTOR BASE can be programmed using GST handheld
programmer (P-9910), purchased
BASE MOUNTING
separately. Connect the two wires of the
handheld programmer to any two opposite
terminals of the detector.

according to the wiring diagram. The cable
must be fire rated type and the size depends
on the wiring distance and application.
I−91XX
DETECTOR
Minimum size gauge 1.0mm²(18 AWG)
TERMINALS
1 2
MOUNTING DETECTOR TERMINAL
FROM CONTROL PANEL TO NEXT DEVICE FIELD DEVICE PROGRAMMER
1 PAIR FIRE CABLE 1 PAIR FIRE CABLE
4 3
Selection of compatible Control Panels

Compatible with all GST Intelligent Fire
Alarm Panels GST 100, GST 200, GST 500,
GST 5000, GST 9000.
Ordering Information:
Part No Description Weight Pack
The Intelligent Multi sensor should be /Kg Qty
installed in compliance with all local codes per
having a jurisdiction in your area or NFPA 72 Box
National Fire Alarm Code, NFPA 70 National I-9101 Intelligent Multi 0.123 120
Electrical Code, BS 5389 and EN54. Before Sensor
installation verify the proper wiring and base DZ-03 Standard 0.050 360
are firmly mounted to prevent detector Detector Base
damage before the installation. Point the

rotating it clockwise until it reaches the next
mark line.

Intelligent Optical
Smoke Detector I-9102
The integral microprocessor analysis the
programmed fire scenarios and smoke
patterns for a faster and safer response. By
intelligent analysis, the smoke detection
sensitivity will be automatically adjusted
according to temperature change,
providing a rapid response.


term changes caused by aging, humidity,
temperature, dust, etc. constant
Features and Benefits monitoring and self adjusting, the I-9101
updates sensitivity base line for its sensing
1. Built in 8 bit microprocessor element. Even when the detector raises a
2. Algorithm maps for faster response warning advising that it requires cleaning,
and false alarm rejection the sensitivity remains the same as the day
3. Analogue sensing it was installed.
4. Secure and speedy communication
5. Intelligent Linear Drift compensation Electronic addressing can be done through
6. Self diagnosis and history log Handhold Programming device (P-9910),
7. Electronic addressing purchased separately.
8. Sensing chamber for exceptional dust
Technical Specifications
proof ability
• Standard: EN54-part7
10. Built-in remote indicator output
• Approval: LPCB,CE
11. Low profile design
• Operating voltage: 24Vdc Loop
Description
voltage
• Operating Current:
The I-9102 Optical Smoke Detector is the
• Standby current 0.6mA
ideal device for most application due to its
• Alarm Current 2mA
excellent linear response to a wide variety of
• Operating temperature: -10°C to
different type of smoke patterns. The unit
+50°C
meets the sensitivity requirement of EN 54
• Relative humidity: 95%
part 7, European Standard and approved by
• Application: Indoor use
Loss Prevention Certificate Board (LCPB).
than 6m, 80 sqm less than 6m
Aesthetically pleasing with a low profile
• Field Programmable sensitivity:
design, unobtrusive to complement modern
0.10dB/m to 0.56dB/m – 3 level
building designs. The unit incorporates an
• Visual Indicator: twin LED, Red ( lit
intelligent processor that provides Algorithm
steady when alarm, 3 sec interval
map, Built-in A/D converter, Drift
blinking at normal state)
compensation, Self Diagnosis and history log.
• Material and colour: ABS, off-white
5cm

Intelligent Optical
Smoke Detector I-9102 CONCRETE PAD OR
HOLDING PAD
EMBEDDED BOX

base DZ-03.Multiple-direction design allows
surface mount only, mount on standard
1gang electrical back box with a mounting LED INDICATOR
hole of 65mm spacing ROTATE CLOCKWISE

HOLDING PAD
SCREW Programming
The address of the detector and sensitivity
HOLE
can be programmed using GST handhold
STANDARD DETECTOR BASE
BASE MOUNTING handheld programmer to terminals 1 and 3
of the detector.
according to the wiring diagram below;
terminal 1 and 3 for the loop; connection of
remote indicator output is on terminals 2 and
I−91XX
4. The cable must be fire rated type and the DETECTOR
size depends on the distance and application.

DETECTOR TERMINAL
TERMINALS
TO NEXT DEVICE
1 PAIR FIRE CABLE Selection of compatible Control Panels
1 2 Compatible with all GST Intelligent Fire
FROM CONTROL PANEL Alarm Panels GST 100, GST 200, GST 5000
and GST 9000.
1 PAIR FIRE CABLE
4 3
REMOTE INDICATOR
Detector Installation /Kg Qty
per
The Intelligent optical smoke detector should
Box
be installed in compliance with all local codes
I-9102 Intelligent 0.123 120
having a jurisdiction in your area or NFPA 72 Optical Smoke
National Fire Alarm Code, NFPA 70 National Detector with
Electrical Code, BS 5389 and EN54. Before Remote
installation verify the proper wiring and base Indicator
are firmly mounted to prevent detector DZ-03 Standard 0.050 360
damage before the installation. Point the Detector Base
rotating it clockwise until it reaches the next MANUFACTURED IN ACCORDANCE WITH
mark line.

Intelligent Dual Heat
Detector I-9103
Meets the sensitivity requirement of EN 54
part 5 and part 6 European Standard and
approved by Loss Prevention Certificate
Board (LCPB).
Aesthetically pleasing with a low profile

intelligent processor that provides
Algorithm map, Built-in A/D converter, Drift
compensation, Self Diagnosis and history
log.

Features and Benefits The integral microprocessor analysis the

digital signal converted from analogue
Dual fixed temperature heat detector. Electronic addressing can be done through
Combining both fixed temperature and rate Handhold Programming device (P-9910),
of rise heat detection in a single sensor. purchased separately.
As standard the fixed temperature is set to
66ºC while the rate of rise is set to 6ºC in
one minute. Technical Specifications
The rate of rise function can be switched off
and the fixed temperature can be adjusted • Standard: EN54-part5/ part6
between 54 and 74 degrees C • Approval: LPCB,CE
1. Built in 8 bit microprocessor • Protection rating: IP 22
2. Algorithm maps for false alarm • Operating voltage: 24Vdc Loop
rejection voltage
3. Analogue sensing • Operating Current:
4. Secure and speedy communication Standby Current 0.8mA
5. Drift compensation Alarm Current 1.4mA
6. Self diagnosis and history log • Operating temperature: -10°C to
7. Electronically addressed +80°C
8. Twin LED for 360º vision • Fixed Temperature adjustments:
9. Low profile design between 54ºC to 80°C
10. Built-in remote indicator • Relative humidity: 95%
11. Fixed temperature response is • Application: Indoor use
adjustable via hand held • Detecting range: 30 sqm for normal
programming tools. area; and 20 sqm for high risk
• Field Programmable sensitivity: 3
level
Description • Visual Indicator: twin LED, Red ( lit
This detector is extremely reliable for blinking at normal state)
application in places where may have high • Material and colour: ABS, off-white
dust levels or smokey environments, • Wiring: 1 pair non polarized
making a normal smoke detector unsuitable , • Dimensions: diameter 10cm; height
for example boiler/plant room, cars parks, 5cm
kitchen, loading bays, furnace/kiln rooms.

Intelligent Dual Heat
Detector I-9103
HOLDING PAD

surface mount only, mount on embedded box;
1gang UK standard. LED INDICATOR
ROTATE CLOCKWISE
HOLDING PAD
SCREW
Programming
HOLE The address of the detector and sensitivity

STANDARD DETECTOR BASE can be programmed using GST handhold
BASE MOUNTING separately. Connect the two wires of the
handheld programmer to terminals 1 and 3
Wiring and Connection of the detector.

according to the wiring diagram below;
terminal 1 and 3 for the loop; connection of
remote indicator output is on terminals 2 and
4. The cable must be fire rated type and the I−91XX
DETECTOR
size depends on the distance and application.

TERMINALS
TO NEXT DEVICE
1 PAIR FIRE CABLE
DETECTOR TERMINAL
1 2

FROM CONTROL PANEL
1 PAIR FIRE CABLE
4 3
REMOTE INDICATOR

Detector Installation and GST 9000.
The Intelligent Dual Heat Detector should be Ordering Information:

installed in compliance with all local codes
having a jurisdiction in your area or NFPA 72 Part No Description Weight Pack
National Fire Alarm Code, NFPA 70 National /Kg Qty
Electrical Code, BS 5389 and EN54. Before per
Box
installation verify the proper wiring and base
I-9103 Intelligent Dual 0.123 120
are firmly mounted to prevent detector
Heat Detector
damage before the installation. Point the with Remote
detector in the base by the mark-line and Indicator
secure the detector in that position by Output
rotating it clockwise until it reaches the next DZ-03 Standard 0.050 360
mark line. Detector Base
Note: Specifications are subject to change without notice

Intelligent Ultraviolet
Flame Detector I-9104
The integral microprocessor analyses the

programmed fire scenarios and flame
patterns for a faster and safer response.

Features:
Electronic addressing can be done through
1. Built in 8 bit microprocessor Handhold Programming device (P-9910),
2. Not sensitive to sunlight purchased separately.
3. Dust /corrosion/humidity resistante
5. Self diagnosis and history log
6. Standard calibration set to detect a
3cm flame at 6metres
7. Effective range up to 12 metres
8. 110º effective detection dispersion
angle
9. Electronic addressing
Standby current 1.5mA
Alarm Current 10mA
Description:
• Operating temperature:-10°C to
+50°C
The I-9104 Intelligent Ultraviolet Flame
Detector is fast and capable to detecting the
ultraviolet (UV) rays emitted by a burning
• Detection angle: 80 degree
substance, used in high hazard applications
• Programmable sensitivity: 3 levels
such as petrochemical plants, munitions
• Visual Indicator: LED, Red ( lit
factories and other areas where flammable or
explosive liquids or solids are handled or
stored.
The I-9104 sensor provides an ultraviolet
photosensitive tube, with qualities of highly
5cm
sensitive, reliable, dust-resistant, corrosion-
proof and moisture-resistant. The sensor is
not sensitive to sunlight, dust, oil, fume, and
humidity. Set as a standard calibration to
detect a 3cm flame at a distance of 6 meters
with a total effective range of 12 meters. Has
unique electronic addressing to provide
specific location, information and monitor
condition.

Intelligent Ultraviolet
Flame Detector I-9104
Mounting Standard Base HOLDING PAD
The detector is mounted using our standard

easy direction adjustment. Suitable for MARK−LINE 2ND MARK−LINE
surface mount only, mount onto standard one

gang electrical box with a mounting hole that
have 65mm spacing.
LED INDICATOR
CONCRETE PAD OR EMBEDDED BOX ROTATE CLOCKWISE

HOLDING PAD
SCREW Programming
The address of the detector and sensitivity

HOLE
STANDARD DETECTOR BASE
BASE MOUNTING separately. Connect the two wires of the
handheld programmer to any two opposite
Wiring and Connection terminals of the detector.

according to the wiring diagram. Terminal 1
and 3 is for loop bus. The cable must be fire
rated type and the size depends on the I−91XX
distance and application. Minimum size gauge

DETECTOR
1.0mm².
TERMINALS
1 2
MOUNTING
DETECTOR TERMINAL
FROM CONTROL PANEL TO NEXT DEVICE

1 PAIR FIRE CABLE 1 PAIR FIRE CABLE
4 3

GST 9000.
Detector Installation Ordering Information:
The Intelligent sensor should be installed in Part No Description Weight Pack

compliance with all local codes having a /Kg Qty
jurisdiction in your area or NFPA 72 National per
Fire Alarm Code, NFPA 70 National Electrical Box
Code, BS 5389 and EN54. Before installation I-9104 Intelligent 0.123 120
Ultraviolet
verify the proper wiring and base are firmly
Flame Detector
mounted to prevent detector damage before DZ-03 Standard 0.050 360
the installation. Point the detector in the Detector Base
base by the mark-line and secure the
detector in that position by rotating it MANUFACTURED IN ACCORDANCE WITH
clockwise until it reaches the next mark line.

Intelligent Reflective
Beam Detector I-9105R Built-in intelligent microprocessor, the
detector has strong ability of analysis and
judgment. The detector automatically
carries out system adjustment,
compensation and variation of ambient
data.
almost limitless cause and effect scenarios
The detector is ideally suited to historical

buildings, warehouses, large storages,
shopping malls, leisure centres, exhibition
halls, hotel lobbies, printing houses,
clothing factories, museums and prisons, as
well as places where slight smoke particles
Features and Benefits or corrosive gas exist.
1. Wide monitoring area, range 8-100 Technical Specifications

metres
2. Combination of the emitting and • Standards: BS EN54 Part-12
receiving parts makes mounting easy • Approvals: LPCB, CE
and accurate optical pathway • Protection Rating: IP20*
3. Simple and cost effective to install • Operating Voltage
transmitter and reflective via ‘honey Power Voltage: 24Vdc (±10%)
comb’ mirror. Loop Voltage: 24Vdc
4. Quick and easy to set up, visual • Operating Current
strength indication. Standby current: 12mA
5. Built-in microprocessor Alarm current: 22mA
6. Self-diagnosis function can monitor • Length of Optical Pathway:
for internal faults 8-100meter
7. Automatic compensation for factors • Monitoring width: 14m
weakening received signals, such as • Monitoring Area: 1400m²
dust contamination, positional • Operating Temperature:
movement and ageing of the -10°C to +50°C
transmitter. • Field Programmable Sensitivity:
8. Electronically addressed 3 levels
9. Three selectable lavels of sensitivity • Relative humidity: 95%
adjustment. • Application: Indoor use
10. SMT processing technology • Material and Colour: ABS, Gray
11. Attractive and pleasing appearance • Wiring: 1 pair -24Vdc, 1pair- loop
• Dimensions:206mmX95mmX95mm
Description Indication of Detector Status

I-9105R Intelligent Reflective Beam Detector
works on the principle of reflective infrared Commission: Green LED and Yellow LED
beam smoke detector that can be directly are lit or flash in a sequence.
connected to a fire alarm loop. Transmitting Normal monitoring state: Red LED
status information via the loop between the flashes periodically (with loop connected)
detector and controller. The detector must be Fire: Red LED constantly illuminates, and
used together with a reflector. The number of Yellow LED turns off. The fire signal has to
reflector(s) to be used (one or four) depends be reset by the controller
on the distance from the detector. Fault: Yellow LED constantly illuminates.

Intelligent Reflective
Beam Detector I-9105R

according to the wiring diagram. The D1,
D2 is for 24VDC power supply. The Z1, Z2
for loop. The cable must be fire rated and
the size depends on the distance and
application. The minimum size gauge
1.0mm²
LOOP IN LOOP OUT
TO POWER SUPPLY
24VDC
D1 D2 Z1 Z2
Mounting the Detector Selection of compatible Control Panels
The Intelligent beam detector should be Compatible with all GST Intelligent Fire
installed in compliance with all local codes Alarm Panels GST 200, GST 500, GST 5000,
having a jurisdiction in your area or NFPA 72 GST 9000.
Electrical Code, BS 5389 and EN54. The
detector can be mounted in 2 ways: the
installed onto standard two gang electrical Ordering Information:
box, or directly by drilling the holes and
fixing with plugs. Part No Description Weight Pack
/Kg Qty
per
Box
I-9105R Intelligent 1.3 10
Reflector Beam
Detector

Addressable Gas
Detector I-9602LW
• Protection rating: IP30

• Operating Voltage:
Loop Voltage: 24V
Range Allowed: 16V 27V
Power Bus Voltage: DC24V
Range Allowed: DC16V DC30V
Standby Current: 80mA (power
bus); 2.7mA (signal bus)
• Alarming Current: 100mA (power
bus) ; 5.2mA (signal bus)
• Output Capacity and Control Mode:
Features and Benefits A group of one-way DC pulse active
contact (1000μcapacitance
1. Build-in microprocessor discharge).
2. Self-diagnosis function can monitor • A group of passive normally open
the inner fault. contact.
3. Built-in relay contacts for control Gas
• Alarm Density:
Valve/Extract etc.
Level 1 3080ppm (14% LEL)
4. Built-in Sounder
5. Manual reset and control of relays Level 2 4400ppm (20% LEL)
contact. • Indicators:
6. Electronically addressed • Power Supply LED: Green
7. Wall mounting. Easy installation and constantly lit in operation.
connection. • Alarm LED: Red, flashes per 4s-5s
8. Available in LPG, Coal Gas and in polling.
natural Gas • Flashing frequency is about 1Hz in
level 1 and about 3Hz in level 2.
• Fault LED: Yellow, constantly lit
Description when in fault.
• Programming Mode: Electronic
I-9602LW Addressable Gas Detector is
programming within 1-242.
suitable to detect liquefied petroleum gas in
• Life of Sensor: 5 years
such areas as houses, hotels and apartments.
• Operating Environment:
This detector is available for different
• Temperature: 0ºC~ +50 ºC
application such as LPG, Natural Gas and
• Relative Humidity≤95%, no
Coal gas. (Please specify at the time of order).
condensation
• Dimension: 176mm×80mm×45mm
The detector adopts semiconductor gas
• Material and Color of Enclosure:
sensitive components enabling stable
ABS, ivory white
operation and simple installation. It's
• Signal two-wire, non-polarized.
powered by centralized DC24V that can be
• Weight: 230g
connected with GST fire alarm controller by
• Mounting Hole Distance: 156mm
non-polarized two-wire, to form a loop type
fire alarm system together with other
detectors. It has two alarm levels: level 1
and level 2.

Addressable Gas
Detector I-9602LW
Mounting Gas Detector
The installation of gas detector should comply

with all local codes and / or NFPA 72 National
Fire Alarm Code, NFPA 70 National Electrical
Code. Designed to install onto standard
conduit electrical box (70mmx70mm). Output Socket Knock- of f Hol e
Recommended location of the detector is
show below.
Programming
Ceiling The address gas detector can be

programmed using GST handhold
Smoke separately. Connect the two wires of the
Exhauster
handheld programmer to terminals Z1 and
Natural Gas and
Coal Gas Detector
Z2 of the detector.
¡Ý cm
Gas 1. 5m<L<4m
Stove
V1 V2 Z1 Z2 D1 D2
Liquefied Petroleum
Gas Detector Within 30cm
Floor
Wiring and Connection Selection of compatible Control Panels
Connect the wires to the required terminal Compatible with all GST Intelligent control
according to the wiring diagram. D1, D2: To panel.
power bus, non-polarized. Z1, Z2: To signal
bus, non-polarized. V1, V2: To pipe pulse Ordering Information:
solenoid valve, when the detector alarms, Part No Description Weight Pack
there is a forward 12V pulse between V2 and /Kg Qty
V1 (V2 is + and V1 is -). per
Box
I-9602LW Addressable .230 100
Gas Detector

GST Duct Probe
DP9100
• Sampling tube: 30 inches (cut
according to duct width).
• Air Velocity: 100 to 4,000 ft. /min.
• Operating temperature: 0°C~70°C
• Material and colour: Grey plastic
backbox,clear plastic cover
• Wiring: solid-12 to 22 AWG
terminals
• Dimensions: 13.5 x 4.5 x 2.5
inches
• Hardware: 7 inches exhaust tube,
sampling tube end cap, mounting
template, and mounting hardware
included.
Features and Benefits Duct Probe Installation
1. Pre-wired detector base Installation of GST duct probe mounted

2. Lid removal raises fault indication at within the duct should be located on the
panel side or the top of the duct. Identify the
3. Advanced detector head design yields code compliant location (return or supply
internal dust filtering side or both) install within the duct in a
4. Clear visual cover fitted location that provides easy access for
5. Staggered terminal blocks for easier viewing and maintenance, refers to manual
wiring for additional information.
6. Duct wall gasket on back of enclosure
are pre-installed
7. Easy maintenance
8. Compatible with GST optical
detectors
Description
The DP9100 Duct Probe is the latest
innovation for early detection of smoke
present in the air moving through HVAC
ducts in commercial, industrial and
residential application. The unit is designed to
prevent the circulation or spread of smoke
within air handling systems, fans and blowers.
The complete system may be shutdown in
the event of smoke detector alarm provided
by the fire alarm control panel.The GST Duct
Probe is built to meet the all local code
Refer to installation manual.
requirements.
Part No Description Weigh Pack
Compatible with all GST Addressable and t/Kg Qty
Conventional Optical Smoke detector. per
Box
DP9100 GST Duct Probe 0.99 1

DZ-03 Base
Technical Specification
• According to Standard: UL268 and

LPCB, GB4715-93
• Wiring: Polarized two-wire with
power cable.
Temperature: -10 ºC +50 ºC
Relative Humidity≤95% no
condensation
• Dimension: Diameter;103mm
Height;14mm
• Material and Color: ABS, ivory
white
• Flame Class:V-0
• Weight: About 54g
• Mounting Hole Distance:45mm to
75mm
Feature
A Description Label
Record Label
B
• Non polarized terminals Multi-
positioning designs allows easy
direction adjustment of the
detectors
• Compatible with GST conventional
detectors using 4K7 Ohms resistor
EOL Mounting
• Common base for GST 1- Hole
Anti-tamper Hole
9101/2/3/4
Description
DZ-03 Base is used to mount conventional Wiring and Connection
and intelligent smoke, heat and Refer to installation detectors manual.
combination detectors as their conductive
base. It’s made of flame-resistant plastic Ordering Information:
ABS, which is a UL94 listed material. It
features attractive appearance, novel Part No Description Weigh Pack
structure and stable performance. Its t/Kg Qty
flame class is V-0. During installation, you per
Box
can easily fix the base before connecting
DZ03 GST Standard 0.059 360
cables, and then twist the detector onto the Base
base. DZ-03D GST Standard 0.059 360
Diode Base

Addressable Manual
Call Point I-9201
Features: • Standards: EN54 Part-11

• Approvals: CE
voltage
• Operating current:
• Standby current 0.8mA
Alarm Current 2mA
+50°C
• N/O Output contact: 60Vdc, 0.1A
• Contact resistance: 100mΩ
B-9201 • Relative humidity: 95%
Features and Benefits
• Material and colour: ABS, red
1. Re-settable (non-breaking glass)
2. Additional volt free contact
• Dimensions: 90x122x48.5mm
3. Electronically addressed
4. Friendly installation and test Mounting Base
5. Suitable for semi-flush and surface The addressable Call point should be
mount installation installed in compliance with all local codes
6. Stylish pleasing design having a jurisdiction in your area or NFPA
72 National Fire Alarm Code, NFPA 70
National Electrical Code, BS 5389 and EN54.
Description: Surface mount and it is installed onto a
standard one gang electrical box with a
Designed for the purpose of raising an alarm mounting hole that has 52mm~68mm
manually once verification of a fire or spacing.
emergency condition has occurred. By
pressing the non breakable glass. The I-9201
I−9201
constructed of high impact red ABS and WALL
smooth shiny appearance on the surface.

Stylish pleasing design and easy to install for FIRE
ELECTRICAL
modern building interior. BACK BOX
Complete with terminating back box enables

first fix installation and termination leaving MOUNTING
BASE
the fascia with integral electronics to be
simply plugged into pace at the time of SURFACE MOUNT
commissioning. Non breakable glass that can
be reset with the GST standard reset tool.
I−9201
The I-9201 operated via a micro-switch that WALL
when pressed a signal will be transmitted
and the volt free contact will be latched.
FIRE
B−9201
Contain integral LED indicator to denote BACK BOX
operational mode.

Handheld Programming device (P-9910),
purchased separately. SEMI FLUSH MOUNT

Addressable Manual
Call Point I-9201

Selection of compatible Control
Panels
according to the wiring diagram. The Z1, Z2
Compatible with all GST Fire Alarms Panels
is for addressable Loop, non-polarized while
GST 100, GST 200, GST 5000, GST 9000.
the K1, K2 is intended to normally open
passive contacts, can provide DC 500mA
control signal when the 24VDC power bus is
connected. The cable must be fire rated type
Part Description Weight Pack
and the size depends on the distance and
No /Kg Qty
application. Minimum size gauge 1.0mm²
per
Box
I-9201 Addressable 0.153 120
Manual Call
1 2 3 4 5 6
Point
B-9201 Semi-flush 0.089 120
7 8 9 10 11 12
Mount Box
K1 K2 Z1 Z2
LOOP IN LOOP OUT
Programming
The address of the manual call point can be

programmed using GST handheld
programmer to Z1 and Z2 terminals of the
manual call point (I-9102).
6 5 4 3 2 1
12 11 10 9 8 7
Z1 AND Z2
TERMINAL


Addressable Manual
Call Point I-9202
• Standard: EN54-part 11
• Approval: LPCB,CE
Alarm Current 2mA
+50°C
Features and Benefits • Visual Indicator: LED, Red ( lit
1. Compatible with latest EN standards blinking at normal state)
2. Re-settable (non-breaking glass) • Front Cover: Plastic glass (optional)
3. Optional flipping plastic cover (C-92FC) • Material and colour: ABS, red
4. Additional volt free contact • Wiring: 1 pair non polarized
5. Electronically addressed (by P-9910B) • Dimensions: 97x100x45.5mm
6. Friendly installation and test
Description
Mounting Base
Designed for the purpose of raising an alarm
manually once verification of a fire or The manual call point should be installed in
emergency condition has occurred. By compliance with all local codes having a
pressing the non breakable glass. Meets the jurisdiction in your area or NFPA 72
standard requirement of EN 54 part 11, National Fire Alarm Code, NFPA 70 National
European Standard and approved by Loss Electrical Code, BS 5389 and EN54. Surface
Prevention Certificate Board (LCPB). mount and it is installed onto a standard
The I-9202 constructed of high impact red one gang electrical box with a mounting
ABS with a modern pleasing appearance. The hole that has 52mm~68mm spacing.
terminating back box enables first fix
installation and termination leaving the fascia
with integral electronics to be simply plugged
into base at the time of commissioning. Non
breakable glass that can be reset with the I−9202
GST standard reset key. WALL
The I-9202 operated via a micro-switch that
when pressed a signal will be transmitted to FIRE
the panel and the volt free contact will be ALARM ACTION
ELECTRICAL
latched. Contains integral LED indicator to BACK BOX
confirm operation. PRESS HERE

Handheld Programming device (P-9910B), MOUNTING
BASE
purchased separately.

Addressable Manual
Call Point I-9202
Panels
GST 100, GST 200, GST 5000, GST 9000.
is for addressable Loop, non-polarized while
the K1, K2 is intended to normally open
passive contacts, can provide 100mA/24Vdc
capacity.. The cable must be fire rated type
and the size depends on the distance and Ordering Information
application. Minimum size gauge is 1.0mm².
/Kg Qty per
Box
62mm
I-9202 Addressable 0.150 120
Manual Call Point
C-92FC Anti Tamper 0.03 120
Security Cover
1 23 4
5 6 7 8
K1 K2 Z1 Z2
LOOP IN
LOOP OUT
Programming
The address of the manual call point can be

programmer (P-9910B), purchased separately.
programmer to Z1 and Z2 terminals of the
manual call point (I-9202)
Z1 AND Z2
TERMINAL

Anti Tamper Security
Cover C-92FC
1. Anti Tamper Security Cover

2. Compatible with I-9202 and DI-9204
3. Easy to install
Description
Designed to protect manual call point from an accidental operation and suitable for 92 MCP
series. The C-92FC constructed of high plastic quality with a modern pleasing appearance.
• Material and colour: transparent flexi glass

• Dimensions: 97x100x20mm
Ordering Information
Part No Description Weight/Kg Pack Qty per

Box
C-92FC Anti-Tamper Security Cover 0.02 120

Addressable Input
Module I-9300
• Test Standard: CEA-GE1.084:200

• Approval: LPCB, CE
• Input: programmable NO/NC
voltage
Monitoring current: 1mA
Action Current: 5mA
+55°C
• EOL Resistor : 4.7 K ohms
• Addressing: 242 using P-9910
• Visual Indicator: LED, steady red
when in alarm state, 3 sec interval
1. Monitors switch contacts of remote
blinking at normal state; Yellow
equipment
(fault)
2. Monitored cable
3. Programmable Inputs (NO/NC)
4. Loop powered
• Dimensions: 120mmx80mmx40mm
6. LED status indicator
7. First fix base for easy and safe
Mounting Module Base
installation
The module should be installed in
compliance with all local codes and/or NFPA
72 National Fire Alarm Code, NFPA 70
Description National Electrical Code, BS5389, and EN45.
It is installed onto a standard one gang
I-9300 Addressable Input Module is used to electrical box with a mounting hole that
receive normally open or normally closed have 6.5cm spacing.
control signals from interfaced equipment,
and transmit the messages back to fire alarm
control panel. The units ideal for use in water
flow indicator, pressure switch, position I−9300 WALL
switch, signal valves and external interface
devices. When these devices operate, the ELECTRICAL
BACK BOX
output signal can be transmitted to fire alarm
control panel via the module through the fire
alarm loop to generate alarm, and activate Addressable Input Module Action
other relevant devices.

MOUNTING
Electronic addressing can be done through BASE
Handheld Programming tool (P-9910),

Addressable Input
Module I-9300
Wiring and Connection Selection of compatible Control Panels
Connect the wires to the required terminal Compatible with all GST Intelligent Fire
according to the wiring diagram. The Z1 (14), Alarm Panels GST 200, GST 5000, GST
Z2 (15) connect to addressable fire detection 9000.
loop, non-polarized, while G (11) and I1 (12)
connect to field device passive contact. The Ordering Information:
cable must be fire rated type and the size
depends on the distance and application. Part No Description Weight Pack Qty
Minimum size gauge 1.0mm²(18 AWG) /Kg per Box
I-9300 Addressable .180 120
Input Module
G I1 Z1 Z2
NO/NC
FIELD DEVICE
LOOP IN LOOP OUT
Programming
The address of the module and device type

programmer to Z1 (14), Z2 (15) terminals of
the module.fig1
1 2 3 4 5 6 7 8
16 15 14 13 12 11 10 9
Z1 (14) AND Z2 (15) TERMINAL

FIELD DEVICE
PROGRAMMER

Addressable Input/Output
Module I-9301 / I-9303
I-9301 Single I/O I-9303 Double I/O
Features and Benefits The input can be linked through a volt free
contact switch output of ancillary
1. Addressable I/O with 24Vdc/5A, equipment reporting to the fire alarm
110Vac/3A relay output contacts controller. According to the pre-inputted
2. Input can be configured as NO/NC or cause and effects interface programming,
self confirmation output the alarm controller sends out a start
3. LED status indicator command to the equipment required to
4. Electronically addressable start. After receiving the command, the
5. Characteristics one input or output module activates its relay to change state.
6. First fix base for easy and safe Once the equipment under control has
installation. operated a confirmation signal can be sent
Description back to the fire alarm controller. The I-
9303 has two addresses, which can receive
Intelligent addressable input/output module. A the two different action orders from the
single/double volt free relay with N/O and N/C controller and has two different control
change over contacts that can be driven via outputs and can affirm two different input
the fire alarm loop. Commonly used for answering signals. Electronic addressing
overriding equipment such as AHU’s, Smoke can be done through Handheld
extracts, Lift returns, auto dialer, BMS, etc. Programming tool (P-9910), purchased
separately.
Specification
Part Number I-9301 I-9303

Protection rating IP 30
Approval LPCB
Output control mode Relay NO/NC passive contacts
Output capacity Passive:5A/24Vdc(3A/110Vac) ; Active: 24Vdc/ 1A
Relay contact One Two
Operating voltage Loop 24Vdc (16~28Vdc); Supply voltage 24Vdc(16~28Vdc)
Operating current loop Standby: 1mA ; Action: 5mA
Operating Temperature -10°C to 50°C @ 90% relative humidity
Electronic programming with 1~242, Electronic programming with 1~242,
Addressing Mode
occupying 1 address occupying 2 addresses
Application Indoor use
Materials and colour ABS / Ivory white
Dimension 120mm x 80mm x 39mm
6 wires: 2 wire for loop ( non- 8 wires: 2 wire for loop ( non-
Wiring polarized) ; 2 wire for power cable( non- polarized) ; 2 wire for power cable( non-
polarized) ; 2 wire for contact polarized) ; 4 wire for contact

Addressable Input/Output
Module I-9301 / I-9303
Programming
Module Installation
The address and device type of the module
The module should be installed in compliance
with all local codes and/or NFPA 72 National
Code, BS5389, and EN45. It is installed onto a
handheld programmer to Z1 (14) , Z2 (15)
standard one gang electrical box with a
terminals of the sounder. For programming
mounting hole that have 6.5cm spacing.
I-9303, the first address it will take the
next address also.
I−930X
WALL
Action
Intelligent I/O Monitor Unit
ELECTRICAL
BACK BOX 1 2 3 4 5 6 7 8
MOUNTING
BASE
16 15 14 13 12 11 10 9


connect to addressable fire detection loop, FIELD DEVICE
non-polarized, the D1, D2 is for 24VDC power PROGRAMMER
supply, non-polarized, the I1 and G connect
with passive NO contact of the control device,
NC1, COM1, NO1 is for first Output Circuit. The
NC2, COM2, NO2 is for the second output Selection of compatible Control Panels
terminals+ and G is continual 24Vdc output for
D1, D2 for active control rated at 1A The cable Compatible with all GST Intelligent Fire
must be fire rated type and the size depends Alarm Panels GST 200, GST 5000, GST
on the distance and application. Minimum size 9000.
gauge 1.0mm²(18 AWG)
V+ G COM1 NO1 NC1 COM2 NO2 NC2 Part No Description Weight Pack
/Kg Qty
per
Box
I-9303
Intelligent
Single
I-9301 .198 120
D1 D2 G I1 I2 Z1 Z2 Input/Output
Module
Intelligent
Double
I-9303 .210 120
Input/Output
V+ G COM1 NO1 NC1 Module
I-9301
D1 D2 G I1 Z1 Z2

Addressable Voice
Alarm Control Module
I-9305
• Output Contact: 24Vdc/5A
• Output Contact Mode: Normally
Open or Closed
voltage
• Power Supply: 24Vdc
Loop Monitoring current 1mA
Loop Action Current: 4mA
+50°C
• Visual Indicator: twin LED, Red ( lit
Features and Benefits blinking at normal state) Yellow
(fault)
• Programming mode: Electronic
programming within 1~242,
1. Zonal switch for voice alarm line
2. Multi contact output energized occupying one address
simultaneously. • Material and colour: ABS, ivory-
3. Microprocessor to monitor the cable white
4. Photoelectric isolation for the loop • Wiring: 3 pair non polarized
and power supply. • Dimensions: 120mmx80mmx39mm
6. Twin LED status indicator Mounting Module Base

compliance with all local codes and/or NFPA
Description 72 National Fire Alarm Code, NFPA 70
National Electrical Code, BS5389, and EN45.
I-9305 Voice Alarm Zone Control Module is
electrical box with a mounting hole that has
used to switch between normal broadcasting
6.5cm spacing.
and fire alarm broadcasting in bus type fire
alarm broadcasting system. It switches both
channels. It can receive incoming answering
signal and self-answer after switching to fire
alarm broadcasting and transmit the
switching signal back to fire alarm control
panel to show successful switching. I−9305 WALL
ELECTRICAL
Electronic addressing can be done through BACK BOX
Handhold Programming tool (P-9910),
Action
Addressable Input Module
MOUNTING
BASE

Addressable Voice
Alarm Control Module
I-9305
Wiring and Connection Programming
Connect the wires to the required terminal The address of voice alarm module can be
according to the wiring diagram. The cable programmed using GST handheld
must be fire rated type and the size depends programmer (P-9910), connect the two
on the wiring distance and application. wires of the handheld programmer to Z1
Minimum size gauge 1.0mm²(18 AWG) and Z2 terminals of the module.
Mounting Mounting
SP1 XF1 ZC1 SP2 XF2 ZC2
Hole Hole
8 7 2 1 Mounting Direction
1 2 3 4 5 6 7 8
9 10 15 16
D1 D2 G I1 Z1 Z2
16 15 14 13 12 11 10 9
• D1, D2: 24VDC power, non-polarized

• Z1, Z2: Signal buses of connected
FIELD DEVICE
control panel, non-polarized
PROGRAMMER
• I1, G: Passive output terminal
• ZC1, ZC2: Input terminals of normal
broadcasting cable
• XF1, XF2: Input terminals of fire
alarm broadcasting cable
• SP1, SP2: Output terminals Selection of compatible Control Panels
connecting with speakers

Supply
Alarm Panels GST 200, GST5000, GST

9000.
Loop
Cable for Broadcasting
Background Music
I-9305 Part No Description Weight Pack

Cable for Broadcasting
Fire Alarm
Voice Alarm Zone Control Module

/Kg Qty
per
Box
Voice Alarm
Module
Speakers on Site

Intelligent Sounder
Driver I-9308
• Output Capacity: 500mA
• Control Mode: Pulse
voltage
• Loop Monitoring current 1mA
• Loop Action Current: 4m
• Power Monitoring current: 10mA
Power Action Current:
500mA
Features and Benefits +50°C
• End of Line: 4.7KΩ 1/4watt
1. Interface with conventional polarized • Application: Indoor use
sounder and bell • Visual Indicator: twin LED, Red ( lit
2. Microprocessor to monitor the cable steady when alarm, 3 sec interval
3. Photoelectric isolation for the loop blinking at normal state) Yellow
and power supply. (fault)
4. Electronically addressed • Programming mode: Electronic
5. Utilized two addresses ( Alert and programming within 1~242,
Evacuate) occupying two addresses
6. East installation and connection. • Material and colour: ABS, ivory-
7. Twin LED status indicator white
• Dimensions: 120mmx80mmx39mm
Description
The I-9308 Intelligent Sounder Circuit Mounting Module Base

Module is used to make addressable control
the pre-alarm sound and fire alarm sound or The sounder module should be installed in
conventional sounder/bells. The module compliance with all local codes and/or NFPA
incorporates a cable monitoring incorporates 72 National Fire Alarm Code, NFPA 70
a cable monitoring function. When there is National Electrical Code, BS5389, and EN45.
short circuit, open circuit or power cut, the It is installed onto a standard one gang
module will give fault indication, and the electrical box with a mounting hole has
controller displays a fault condition. Two 6.5cm spacing.
continuously addresses are incorporated. If
the 1st address is active, the module will I−9308
WALL
switch output at ALERT mode, 0.25s ON and
0.75s OFF. If the 2nd address is active, the
output will be in EVACUATE mode, 0.25s ON
and 0.25s OFF. The 2nd address will override Action
the 1st one. It means EVACUATE has the high

Intelligent Sounder Circuit Module
Fault
ELECTRICAL
priority. BACK BOX
MOUNTING
Electronic addressing can be done through BASE
Handhold Programming tool (P-9910),

Intelligent Sounder
Driver I-9308

according to the wiring diagram. The L+.L- is
for sounder output, polarized, the D1, D2 is 1 2 3 4 5 6 7 8
for 24VDC power supply, non-polarized and

the Z1, Z2 is loop of the controller, non- 16 15 14 13 12 11 10 9
polarized. The cable must be fire rated type

and the size depends on the wiring distance Z1 (14) AND Z2 (15) TERMINAL
and application. Minimum size gauge

1.0mm²(18 AWG)
FIELD DEVICE
PROGRAMMER
4.7 Kohms
RESISTOR
O+ O−
D1 D2 I1 Z1 Z2
24VDC SUPPLY
LOOP IN LOOP OUT
NON−P0LARIZED Alarm Panels GST 200, GST 5000, GST
9000.
Programming
The address of Sounder circuit module can be Part No Description Weight Pack
/Kg Qty
per
programmer (P-9910), connect the two wires Box
of the handheld programmer to Z1 and Z2 I-9308 Intelligent .191 120
terminals of the module. Program the 1st Sounder Driver
address, the module will automatically take Module
the next address also. See Manual for more
information

Addressable Zone
Monitor Unit I-9319
voltage
Monitoring current 0.5mA
Action Current: 5mA
+50°C
• Capability: 15 conventional detector
( AEOL); 25 detectors (EOLR)
• End of Line: 4.7KΩ or AEOL
Features and Benefits • Visual Indicator: LED, steady red
when in alarm state, 3 sec interval
1. Interface with conventional fire blinking at normal state; Yellow
devices/non-addressable unit (fault)
2. Secure and speedy communication • Material and colour: ABS, off-white
3. Monitored cable • Wiring: 2 pair non polarized
4. Electronically addressed • Dimensions: 120mmx80mmx40mm
6. Ideal for integrating Sprinkler Zone
Valve and Flow Switches
Mounting Module Base

Description
I-9319 intelligent zone monitor unit is an compliance with all local codes and/or NFPA
addressable interface module, which will 72 National Fire Alarm Code, NFPA 70
integrate conventional detectors or National Electrical Code, BS5389, and EN45.
conventional manual call points to It is installed onto a standard one gang
addressable system. When any of the electrical box with a mounting hole that has
connected devices alarms are active, the unit 6.5cm spacing.
can send the alarm message to fire alarm
controller, which generates alarm signal and
displays its address. The unit can match with
the conventional optical smoke detector,
conventional rate of rise and fixed
temperature detector and conventional I−9319 WALL
manual call point etc. It has the function of
ELECTRICAL
checking short or open circuit of the output BACK BOX
connection, by the End of Line Resistor (EOLR)
or Active End of Line unit (AEOL
recommended). The fault massage includes Intelligent Zone Monitor Unit Action
open circuit, short circuit or any removal of

the detectors. MOUNTING
BASE

Addressable Zone
Monitor Unit I-9319
Typical Wiring Diagram
O+ O−
1 2 1 2 1 2
O+ O−
V+ v−
K1 K2
D1 D2 I1 Z1 Z2 4 3 4 3 4 3
C−9201 MANUAL CALL POINT C−9102 SMOKE DETECTOR C−9103 HEAT DETECTOR P−9907 ACTIVE
I−9319 ADDRESSABLE ZONE MONITOR UNIT END OF LINE

connect to addressable fire detection loop,
non-polarized, the D1, D2 is for 24VDC power
supply, non-polarized and the O-, O+ is for 1 2 3 4 5 6 7 8
Output Circuit, note the polarity. The cable

must be fire rated type and the size depends 16 15 14 13 12 11 10 9
on the wiring distance and application.

Minimum size gauge 1.0mm²(18 AWG) Z1 (14) AND Z2 (15) TERMINAL
CONVENTIONAL ZONE
CONNECTION
FIELD DEVICE
PROGRAMMER
O+ O−
D1 D2 I1 Z1 Z2
Fig.1

LOOP IN LOOP OUT Compatible with all GST Intelligent Fire
24VDC SUPPLY
Alarm Panels GST 200, GST 5000, GST
9000.
Programming /Kg Qty
per
The address of the module can be Box
programmed using GST handhold I-9319 Addressable .180 120
programmer (P-9910), purchased separately. Zone Monitor
Connect the two wires of the handheld Unit
programmer to Z1 (14), Z2 (15) terminals of MANUFACTURED IN ACCORDANCE WITH
the module.fig1

Addressable Multi
Channel Interface
DI-9309
• Operating Loop voltage: 24V

Voltage (16V~28V).
Power Supply Voltage:
24VDC
(20VDC~28VDC).
• Standby Loop ≤1.5mA Power
Current ≤50mA
• Action Loop ≤3mA Power
Current ≤100mA
Features and Benefits • Output Output contact capacity:
Capacity 220V/2A.
• Output Type Dry contact output.
1. Providing Max. 16 channels of • Programming Electronically
independent input. 1-16 selectable. Method programming.
Input signals are insulated from the • Code Range Occupying 3-18
loop. addresses, the output
address of Channel 1
2. Providing two channels of can be set within 1
independent dry contact output. 225. The output address
3. 3-18 consecutive addresses, of Channel 2 is
changing with selected channel automatically increased
quantity. 1 to Channel 1. The
input address of Channel
4. Power supply monitored. n is automatically
5. Cable monitored for open circuit and increased n and 1 to
short circuit Channel 1.
• Action Red.
Indicators Separate polling
Description indicator HL0.
Individual state LED(n)
With microprocessor, DI-9309 Addressable for each channel input.
Flashes in fault state.
Multi-Channel Interface can communicate Illuminates in action
with fire alarm control panel (FACP), monitor state. Quiet in normal
power supply, and judge the logic state of supervisory.
input signal, control output and state HL1 and HL2 for each
indicators. channel output.
Illuminates when
Each output channel occupies an individual activated.
address and receives start command from • Ambient -10°C+50°C
FACP, energizes the related relay, gives dry Temperature
contact output and lights the related action • Relative ≤95%, non condensing
indicator. Each input is corresponded to an Humidity
address to receive the state signal from the • Mounting 190mm× 90mm
equipment and transmit it to FACP. The Hole
quantity of channels can be set by jumpers Distance
• Dimensions 200mm×100mm×20mm
Electronic addressing can be done through (L×W×H)
• Weight About 240g

Addressable Multi
Channel Interface
DI-9309 Programming
Mounting Module Base DI-9309 interface can be addressed in field

with power off by using P-9910B
programmer connected to Z1 and Z2.
The module should be installed in compliance Please refer to P-9910B Hand Held
with all local codes and/or NFPA 72 National Programmer Installation and Operation
Fire Alarm Code, NFPA 70 National Electrical Manual for details.
Code, BS5389, and EN45. It is installed onto
anE electrical box (not included).
190mm Selection of compatible Control Panels

Alarm Panels GST 200, GST 5000, GST
9000.
100mm
90mm
43 21 Ordering Information:
XS3
Part No Description Weight/ Pack Qty
Kg per Box
Addressable
Multi Channel
200mm interface Module
DI-9309 .180 120
(Electrical box
Wiring and Connection excluded in the
1) Fig.2 shows the system connection with volt- package)
free normally open input.
4.7k¦ ¸
470¦ ¸
Volt free
contact
I(n) G
INPUT(n)
Fig. 2
2) Fig.3 shows the system connection with dry

contact output.
+24V
GND
Z1
Z2
D1 D2 Z1 Z2
D I-9 3 0 9
N C 1 (2 ) C O M 1 (2 ) N O 1 (2 )
Control Input
C o n tro lle d E q u ip m e n t

Interposing Relay Module
C-9302 / C-9302A
1. Working together with GST

Input/Output modules , used to
control intensive current facility
switch between AC and DC
2. Two pairs of DC24Vdc /5A NO/NC
for C-9302A
4. First fix base for easy and safe
installation.
Description
C-9302 Interposing Relay Module is a non-addressable module, used together with I-9301
module to control the activating devices with higher current capacity and transforming control
of AC 220V devices in order to avoid mixing of DC and AC voltages to isolate the loop.
Specification
Part Number C-9302 C-9302A

Output control mode Electric level mode, relay always closed
Output capacity n/a 5A/220Vac(5A/24Vdc)
Relay contact One Two
Operating voltage 24Vdc (16~28Vdc) feed by I-9301 24Vdc (16~28Vdc) feed by I-9303
Operating current Standby: 1mA ; Action: 5mA
Materials and colour ABS / Ivory white
2 wire for contact (non-polarized), 2 wire 4 wire for contact (non-polarized), 4 wire
Wiring
connecting I-9301 connecting I-9303

Interposing Relay Module
C-9302 / C-9302A
Module Installation C-9302A Wiring

The interposing relay module should be • A, B: Start command signal output
installed in compliance with all local codes terminal, passive normally open
and/or NFPA 72 National Fire Alarm Code, contact.
NFPA 70 National Electrical Code, BS5389, and • C, B: Stop command signal output
EN 54. It is installed onto a standard one gang terminal, passive normally closed
electrical box with a mounting hole that have contact.
6.5cm spacing. • D: Start answer signal input
terminal, from controlled equipment
I−930X AC220V normally open contact.
WALL
• E: Stop answer signal input
terminal, from controlled equipment
AC220V normally closed contact.
• N: AC220V neutral terminal
Action
Intelligent I/O Monitor Unit
ELECTRICAL
BACK BOX
MOUNTING
BASE

on the distance and application. Minimum size
gauge 1.0mm²(18 AWG)
C-9302 Wiring
• COM, NO, NC: Output signal, passive
normally open, normally closed contact. Selection of compatible intelligent
• O, G: Active DC24V control signal modules
input terminals.
Compatible with GST I-9301 Intelligent
Single I/O Module and I-9303 Intelligent
EQUIPMENT Dual I/O module
AC soure
220vac
/Kg Qty
per
Box
Interposing
C-9302 .198 120
Relay Modules
Double Action
C-9302A Interposing .210 120
relay
To I-9301 Note: Specifications are subject to change without notice.

Short Circuit Isolator
C-9503
Mounting Isolator Base
The integration of fire detection system
should comply with all local codes and / or
NFPA 72 National Fire Alarm Code, NFPA 70
National Electrical Code. Designed to
installed onto standard conduit electrical
box (70mmx70mm).
C−9504
WALL
Action
Short Circuit Isolator
ELECTRICAL
BACK BOX
Features and Benefits MOUNTING
BASE
1. In the event of a short circuit isolates

faulty parts of the loop. Wiring and Connection
2. Automatically resetting once the fault Connect the wires to the required terminal
has cleared according to the wire diagram. The cable
3. Detector Base Isolator also available must be fire rated type and the size
(9504) depends on the distance and application.
4. LED status indicator Minimum size gauge 1.0mm²(18 AWG)
Description
LOOP OUT
In the event of short circuit on the detector

loop the C-9503 Isolators either side of the
loop will defect the problem and open circuit
and isolates the faulty part of the loop,
enabling other devises on the unaffected part
of the loop to operate normally.
The module will continue to monitor for the
fault to be repaired, once the fault is cleared
the isolator will automatically reinstate the C−9503
effected part of the loop.
LOOP IN
• Protection rating: IP 30 Connect as per the marking on the base.
• Approval: LPCB
• Operating voltage: 24Vdc Selection of compatible Control Panels
• Operating Current: 270mA Compatible with all GST Intelligent Fire
• Operating temperature: -10°C to Alarm Panels GST 100, GST 200, GST 9000.
+50°C
• Output Capacity: 30Vdc / 5 mA
/Kg Qty
• Visual Indicator: RED LED ( lit steady per
when alarm, off normal state) Box
• Material and colour: ABS, off-white C-9503 Short Circuit 0.100 120
• Wiring: 1 pair non polarized Isolator
• Dimensions: 120mm x 80mm x
39mm Note: Specifications are subject to change without notice.

Base Mount Circuit
Isolator C-9504
Mounting Isolator Base
The integration of fire detection system
should comply with all local codes and / or
NFPA 72 National Fire Alarm Code, NFPA 70
National Electrical Code. Designed to
installed onto standard conduit electrical
box (70mmx70mm).
CEILING ELECTRICAL
BACK BOX
C−9504
DETECTOR
1. In the event of a short circuit isolates

faulty parts of the loop. Wiring and Connection
2. Automatically resetting once the fault Connect the wires to the required terminal
has cleared according to the wire diagram. The cable
3. Replacement standard detector base (C-must be fire rated type and the size
9504) depends on the distance and application.
4. LED status indicator Minimum size gauge 1.0mm²(18 AWG)
Description
In the event of short circuit on the detector

loop the C-9504 Isolators either side of the
I N£ -
OU
T£
-
loop will defect the problem and open circuit
«
T£
OU
and isolates the faulty part of the loop,

I N£ «
enabling other devises on the unaffected part

of the loop to operate normally.
The module will continue to monitor for the Detector Installation
fault to be repaired, once the fault is cleared Connect as per the marking on the base.
the isolator will automatically reinstate the
effected part of the loop.
Technical Specifications Compatible with all GST Intelligent Fire
• Protection rating: IP 22 GST 5000, GST 9000.
• Operating voltage: 24Vdc
• Operating Current: 270mA
+50°C Ordering Information:
• Application: Indoor use Part No Description Weight Pack
• Output Capacity: 30Vdc / 5 mA /Kg Qty
• Visual Indicator: Yellow LED ( lit per
Box
steady when alarm, off normal state)
C-9504 Base Mount 0.010 120
• Material and colour: ABS, off-white Short Circuit
• Wiring: 1 pair non polarized Isolator
• Dimensions: diameter 105mm;
height 20mm Note: Specifications are subject to change without notice.

Addressable Sounder
Beacon I-9401
• Operating voltage: 24Vdc non-
polarized
24Vdc: Standby current 10mA
Action current 160mA
Loop: Standby current 0.8mA
Action current 6mA
+50°C
• Flashing Frequency: 20x180per min.
• Alarm Volume (SPL): 90dB @
1metre
• Material and colour: ABS,ivorywhite,
red plexiglass
• Wiring: 2 pairs ; 1 pair 24vdc
supply and 1 pair for loop
• Dimensions: 144x90x57mm

Sounder Installation
1. Combined flashing high intensity LED
beacon and sounder The sounder beacon should be installed in
2. Wall mount compliance with all local codes having a
3. Two part plug-in construction, no jurisdiction in your area or NFPA 72
locking screw required National Fire Alarm Code, NFPA 70 National
4. Easy installation and connection. Electrical Code, BS 5389 and EN54. Surface
5. Electronically addressed mount and it is installed onto a standard
one gang electrical box with a mounting
hole that has 52mm~68mm spacing.
Description
Addressable all-purpose sounder beacon for

fire, security, schools and industrial area. The
I-9401 is designed to meet the requirement
of EN54
The unit is utililised a red Plexiglas cover and

a number of strong signal red LED, long-life
and low consumption. Two part construction
with base mounted termination allows easy
installation and avoiding the wiring and
connection problem associated with
traditional sounder.

Handhold Programming device (P-9910),

Addressable Sounder
Beacon I-9401

according to the wiring diagram. The terminal Z1 AND Z2
TERMINAL
1 (Z1), 2 (Z2) is for addressable Loop, non-
polarized, and DI and D2 is for 24vdc
external supply. The cable must be fire rated
type and the size depends on the wiring
D1 D2 Z1 Z2
distance and application. Minimum

recommended size gauge is 1.0mm².
24VDC LOOP
FIELD DEVICE
PROGRAMMER
D1 D2 Z1 Z2
Mounting Hole Mounting Hole

Panels

GST 100, GST 200, GST 5000, GST 9000.
S1 G
Part No Description Unit Pack

Weight Qty
/Kg per
Programming Box
Sounder
The address of the sounder beacon can be
Beacon
programmer to terminals Z1 and Z2 of the
sounder base, refers to manual for additional
information.

Addressable Sounder
Base I-9402
polarized
• Standby current 1mA
• Action current 7mA
+50°C
• Loop capacity: 30 pcs. p/loop
• Sound Output: 85dB @ 1metre
• Material and colour: ABS,ivorywhite
• Wiring: 1 pair polarized
• Dimensions: diameter 10cm;
height : 3.5cm (w/o cover), 4.5cm
(w/ cover)
1. Loop powered sounder

2. Can be used as a detector base
3. Wall mount (stand alone with cover) Sounder Installation
or ceiling mounting
4. Electronically addressed The sounder base should be installed in
5. Easy installation and connection. compliance with all local codes having a
jurisdiction in your area or NFPA 72
Description National Fire Alarm Code, NFPA 70 National
Electrical Code, BS 5389 and EN54. Surface
Life security system of FIRE includes 2 parts, mount and it is installed onto a standard
fire detection and control. In case of fire one gang electrical box with a mounting
comes, the sounder will be the most effective hole that has 52mm~68mm spacing.
device to wake up the person and evacuate
the building. For special buildings like hotel,
the room is isolated by thick wall and heavy
door, alarm sound can not easily reach the
bedroom. So local alarm device is needed. CEILING ELECTRICAL
BACK BOX WALL
GST developed sounder base to achieve the
above function. Electronic addressable and
I−9402 ELECTRICAL
loop powered, convenience to use. Two BACK BOX
addresses to make sounds of ALERT and
EVACUATE. With start signal from FACP
through the loop, I-9402 can be controlled by DETECTOR
program, making ideally order of evacuating.
The sounder base can be used as a common
base with GST intelligent detector or stand DETECTOR COMMON
BASE
alone with a cover.
SOUNDER WITH
Electronic addressing can be done through COVER

Addressable Sounder
Base I-9402
Wiring and Connection Selection of compatible Control

Panels
according to the wiring diagram. The terminal Compatible with all GST Fire Alarms Panels
1 (Z1), 2 (Z2) is for addressable Loop, non- GST 100, GST 200, GST 5000, GST 9000.
polarized. The cable must be fire rated type
and the size depends on the wiring distance
and application. Minimum recommended size
gauge is 1.0mm².
LOOP IN LOOP OUT
/Kg Qty
per
Box
1 2
Sounder Base
4 3
Programming
The address of the sounder, sound level and

device type can be programmed using GST
handheld programmer (P-9910), purchased
handheld programmer to terminals 1 and 3 of
the sounder base. It take two addresses,
program the first address then it will
automatically programmed the next address.
Z1 AND Z2
TERMINAL
1 2
4 3
FIELD DEVICE
PROGRAMMER

Addressable Sounder
and Strobe I-9403 / I-9404
Description
The I-9403 is a detachable, surface

mounted sounder and strobe while the I-
9404 is identical in appearance and
features to the I-9403 but without strobe
element. The audio efficiency and sound
distribution generate over 85 dB at 3 meter
distance giving an excellent audibility from
the device location. Using six highlights
LED’s for high intensity visual alarm to
warn the people. The GST sounder series
Features and Benefits are convenient plug and turn installing
method, two part construction with base
1. High sound level mounted termination allows easy
2. Low power consumption installation and avoiding the wiring and
3. High intensity LED cluster connection problem associated with
4. Remote start input can be used to traditional sounder.
drive with other systems
5. Programmable alarm mode, evacuate
or alert/evacuate mode
6. Electronically addressable
7. Easy installation and connection.
Specification
Part Number I-9403 I-9404
Approval LPCB,CE CE
Standard EN54-part 3
Sound level output Alert Sound: 75dB; Evacuate sound: 85dB ( at 3 meter)
Main Sound Frequency 2.8Khz
Strobe 6 highlight LED’ No feature
Operating voltage Loop 24vdc ; Power Supply 24Vdc(16~28Vdc)
Loop: standby 1mA/ alarm 5mA ; Loop: standby 1mA/ alarm 5mA ; Supply
Operating current Supply current: standby 3mA / alarm current: standby 3mA / alarm 35mA
65mA
Addressing Mode Electronic programming with 1~242
Application Indoor and outdoor use
Materials and colour ABS / red; plexiglass / red
Dimension Ø 110mm x 97.5 mm
Wiring 4 wires: 2 wires for loop ( non-polarized) ; 2 wires for power cable( non-polarized)

Addressable Sounder
and Strobe I-9403 / I-9404
Programming
Sounder Installation The address and mode of sound level of the
The sounder should be installed in sounder can be programmed using GST
compliance with all local codes or NFPA 72 handheld programmer (P-9910), purchased
National Fire Alarm Code, NFPA 70 National separately. Connect the two wires of the
Electrical Code, BS5389 and EN54. It is handheld programmer to Z1 (2), Z2 (4)
installed onto a standard one gang electrical terminals of the sounder.fig1
box with a mounting hole that has 6.5cm
spacing.
WALL
ELECTRICAL
BACK BOX
Z1 AND Z2
TERMINAL
MOUNTING
BASE
Wiring and Connection Compatible with all GST Intelligent Fire

Connect the wires to the required terminal Alarm Panels GST 100, GST 200, GST5000
according to the wiring diagram. The Z1, Z2 and GST 9000.
connect to addressable fire detection loop,
non-polarized, the D1, D2 is for 24VDC power
supply, non-polarized. The cable must be fire
rated type and the size depends on the wiring Ordering Information:
distance and application. Minimum size gauge
1.0mm²(18 AWG) Part No Description Weight Pack
/Kg Qty
Power Supply per
24Vdc Box
Addressable
I-9403 Sounder and 0.360 45
Strobe
Addressable
I-9404 0.361 45
Sounder
Loop out
Loop in Note: Specifications are subject to change without notice.

Addressable Mini Fire
Panel GST100
1. Excellent cost effective replacement

to conventional
2. Aesthetically attractive design
3. Loop capacity 128 addressable
devices.
4. LCD Display and LED indication
5. 8 Zone indication
6. Programmable via panel keyboard
7. Easy to use and simple to
programme
8. Advanced user friendly
programming of Zones and Pre-
alarm
9. Built-in Panel Printer
10. Optional RS 485 Communication
Protocol
Description:
GST100 Addressable Fire Alarm Control Panel is GST’s new-generation mini-panel.

Wall-mounted, unique design for modern technology, flexible configuration and easy
to operate. Suitable for small establishment such as small offices, shops, restaurants,
bars, libraries, supermarkets, transformer substations etc.
The panel displays the zone, time and address with graphical icon once fire and fault
occurs this is saved on a non-volatile memory, which can store up to 999 fire
messages and 500 for fault. By utilizing advanced GST Protocol, the system is
compatible with the complete range of GST intelligent detectors, sounders, interface
module and MCP, and optional RS485 protocol for connecting repeater or networking
to other GST intelligent panels.

Addressable Mini Fire
Panel GST100
Main Input Voltage 220 ± 10% VAC 50/60 Hz

Power Consumption 15 Watts
System Operating Voltage 24 VDC Nominal (17-29 VDC)
Battery 2.3AH/24VDC
Loop Capacity Maximum 120 devices and 8 Sounders
Sounder Output Output voltage 24 VDC
Output current: 400MA
EOL 4.7KΩ to 10 KΩ resistors
Fuses Mains 2A (20mm A/S ceramic)
Sounder: 1A (20mm A/S)
Battery: 2A (20mm A/S HRC ceramic)
Auxiliary Output 24Vdc/500mA maximum
Relay Output (Fire/fault) Volt-free NO/NC
Battery Charging Current Limit 600mA
Dimension 210 x 297 x 90 mm
Selection of GST100 compatible devices and panels
9 GST200/2 Intelligent Single/twin Loops Fire Alarm Panel

9 GST5000 Intelligent Modular 2/4 Loops Fire Alarm Panel
9 GST5000 Intelligent Modular 1-20 Loops Fire Alarm Panel
9 GST 9000 Intelligent Modular 1-42 Loops Fire Alarm Panel
9 GST852RP LCD Passive Repeater Panel
9 GST852RPX LCD Repeater Panel
9 I-9101 Multi detector
9 I-9102 Optical Detector
9 I-9103 Dual Heat Detector
9 I-9104 UV Flame Detector
9 I-9105R Beam Detector
9 I-9200 Series Manual Call points
9 I-9400 Series Sounders and strobes
Notes:
The GST 100 does not provide control for GST intelligent loop driven devices.

Box
GST100 Addressable Mini Fire Alarm Panel 2.25 1

Intelligent Single and
Double Loop Fire Alarm
Panel GST200-2
Description:
The GST 200 single loop twin loop

addressable fire detection control panel is
packed with features that are not usually
associated with smaller systems. The GST
200 provides a high quality solution at
exceptional value.
By utilizing advanced GST Protocol, the

system is compatible with the complete
range of GST intelligent detectors,
Sounders, Call Points, Interfaces, including
intrinsically safe and gaseous extinguishing
control.
The GST 200 is manufactured and certified

to EN54 parts 2 and 4 and to BS5839 Part
4. The GST programming facilities enables
advanced and complex cause and effects to
be programmed with ease, including
phased and cascade evacuation scenario.
The GST zonal indication and control facility
allows the operator to manually intervene,
with evacuation and control of each zone,
including control of all plant equipment
under an alarm condition.
Addressable security control facilities and
1. Loop capacity 235 addresses gas release controls are built in as standard,
2. Graphical LCD Display. making the system ideal for many
3. 30 Zone indication including manual applications such as Banks, Shops,
intervention and control Telecommunication Centers and GSM
4. 3 programmable alarm output exchanges, industrial and commercial
5. Networkable with all GST Intelligent facilities.
Fire Alarm panels
6. Programmable form PC By utilizing the GST protocol the GST200
7. RS485 Repeater Output (Max. 10) can be networked with up to 32 panels, not
8. Built-in gas extinguishing control. only the GST200 single loop panel, but also
9. Integrated Security alarm facilities with the GST5000 four Loop panel and the
10. Advanced user friendly programming GST5000 modular 20 loop controller,
software including ‘Fuzzy Logic’ making this the perfect solution for large
11. Optional Colour Graphics decentralized systems such as Shopping
12. Optional Fireman’s Control Panel Centers Military campus industrial
13. Optional Panel Printer complexes, Holiday villages etc.

Intelligent Single and
Double Loop Fire Alarm
Panel GST200-2
Standard EN54 Part 2/4 ; BS5839 Part 4
Approvals LPCB,TRL Compliance, EEC, CE
Input Current Rating 0.75A
Zone Capacity 30 Zones programmable
Loop length 1.2 Km using 1.5mmsq cable
Standby Batteries Twin 12 Vdc Bat;12AH, 24 hours
Sounder Circuits (3) Output voltage 17 to 29 VDC
Output current: 500mA per output
Maximum total load 1.5A
EOL 10K resistor
Sounders (2): 1A (20mm A/S)
Fire alarm Output 0.5A (20mm A/S)
(Fire alarm) Relay Output 0.5A at 24VDC
Common Fault Relay Output Volt-free changeover 1.0A at 24 VDC
24 VDC Fused Output Maximum load 500mA at 17-28VDC
Selection of GST200 compatible addressable devices and Panels
9 GST5000/2/4 2/4 Loops Intelligent Fire Alarm Controller

9 GST5000/8 4 to 8 Loops Intelligent Fire Alarm Controller
9 GST5000R/C 1-20 Loops Intelligent Fire Alarm Controller
9 GST852RPX LCD Active Repeater Panel
9 DI-9102 Innovation Intelligent Optical
9 DI-9103 Innovation Intelligent Combined Rate of Rise and Fixed Temperature.
9 I-9101 Intelligent Multi detector
9 I-9102 Intelligent Optical Detector
9 I-9103 Intelligent Dual Heat Detector
9 I-9104 Intelligent UV Flame Detector
9 I-9105 Intelligent Beam Detector
9 I-9201 Addressable Manual Call points
9 I-9300 Addressable Series interfaces (Complete range for all requirements)
9 I-9400 Addressable Series Sounders and strobes
9 I-9600 Intelligent Series Combustible gas detectors

Box
GST200 Intelligent 30 zone Single Loop Fire Alarm Panel 12.90 1
GST200-2 Intelligent 30 zone Twin Loop Fire Alarm Panel 12.93 1

Intelligent Two/Four
Loops Fire Alarm Panel
GST5000/2/4
Description:
The GST 5000 Two and Four loops

addressable fire detection control panel is
modular type Intelligent Fire Alarm Control
Panel. The GST 5000 provides a high
quality solution at Exceptional value.
By utilizing advanced GST Protocol, the
range of GST intelligent detectors,
Sounders, Call Points, Interfaces, including
intrinsically safe and gaseous extinguishing
control. GST 5000 is manufactured and
certified to EN54 parts 2 and 4 and to
BS5839 Par 4.
The GST programming facilities enables

phased and cascade evacuation scenarios.
The GST zonal indication and control

facilities allow the operator to manually
Features and Benefits intervene, with evacuation and control of
each zone including control of all plant
1. Graphical LCD Display. equipment under an alarm condition.
2. 60 Zone indication including manual
intervention and control panel. Addressable security control facilities and
3. 3 programmable alarm output gas release control monitoring are built in
4. Networked with all GST Intelligent as standard, making the system ideal for
Fire panels. many applications such as Banks, Shops,
5. Programmable form PC or via on Telecommunication Centers and GSM
board keypad. exchanges, industrial and commercial
6. RS485 Bus Output ( Max. 64 facilities.
Repeaters)
7. Built-in gas extinguishing control. By utilizing the GST protocol the
8. Integrated Security alarm facilities. GST5000/2/4 can be networked with up to
9. Advanced user-friendly programming 32 panels, not only the GST200 single loop
software including ‘Fuzzy Logic’. panel, but also with the GST200/2 twin
10. Optional Color Graphics. Loop panel and the GST5000 modular 20
11. Optional Fireman’s Control Panel. loop controller. Making this the perfect
12. Panel Printer included solution for large decentralized systems
13. Optional Color Graphics. such as Shopping Centers Military campus
14. Optional Fireman’s Control Panel. industrial complexes, Holiday villages etc.
15. GST5000/2 Two loops can connect up
to 480 Addresses
16. GST5000/4 Two loops can connect up
to 960 addresses

Intelligent Two/Four
Loops Fire Alarm Panel
GST5000/2/4
Standard EN54 Part 2/4 ; BS5839 Part 4
Loop Capacity GST5000/2:480 addresses
GST5000/4:960 addresses
Loop Length 1.2Km using 1.5 mmsq.
Standby Batteries 2 x 12AH, 24 hours
Sounder-Alarm Circuits (3) Settable dry contact or 24Vdc Output
Output voltage 17 to 29 VDC
Output current: 1.0A
Maximum total load 1.5A
AOL 10K resistor
Sounders (2): 1A (20mm A/S)
Fire alarm Output 0.5A (20mm A/S)
(Fire alarm) Relay Output 0.5A at 24VDC
Common Fault Relay Output Volt-free changeover 1.0A at 24 VDC
24 VDC Fused Output Maximum load 500mA at 17-28VDC
Dimension 500mm x 700mm x 170 mm
Selection of GST5000/2/4 compatible addressable devices and Panels
9 GST200/2 Single or Twin Loops Intelligent Fire Alarm Controller
9 I-9105R Intelligent Beam Detector
9 I-9201 Addressable Manual Call points
Box
GST5000/2 Intelligent Two Loop Fire Alarm Panel 23.690 1
GST5000/4 Intelligent Four Loop Fire Alarm Panel 23.720 1

Intelligent 8 Loops Fire
Alarm Control System
GST5000/8
The system is compatible with the complete

range of GST Intelligent detectors,
Sounders, Call Points, and Interfaces,
including intrinsically safe and gaseous
extinguishing control. GST 5000/8 is
manufactured and certified to EN54 parts 2
and 4 and to BS5839 Par 4.

The GST zone indication and control
intervene, with evacuation and control of
equipment under an alarm condition. Gas
release control monitoring are built in as
standard.
By utilizing the GST protocol the

GST5000/8 can be networked with up to 32
panels, not only the GST200 single loop
panel, but also with the GST5000/2/4
Loops panel and the GST5000 modular 20
panel, making this the perfect solution for
1. 8 x Loops capacity (1936) large decentralized systems such as
addressable points Shopping Centers Military campus industrial
2. Wall Mounted complexes, Holiday villages etc.
3. 40 x12 lines Colour Graphical LCD
Display. With up to 1936 two-wire fire alarm linkage
4. 60 Zone indication including manual control points that can also be intelligent be
intervention and control panel. connected with many serial products (ex.
5. Networked with all GST Intelligent digital detector, analogue detector,
Fire panels. intelligent detector, control module and
6. Programmable form PC multi-wire control panel).
7. RS485 Repeater Output (Max. 64
Repeaters)
8. Integrated Security alarm facilities.
9. Advanced user friendly programming
software including ‘Fuzzy Logic’.
10. Panel Printer included
11. Separate wall mounted monitored
PSU
12. Built in Battery charger.
Description
The GST 5000/8 is an intelligent fire alarm

control panel. Wall mounted type housing it
provides the perfect solution for all medium
to large system by utilizing advance GST
Protocol.
Power Supply Box

Intelligent 8 Loops Fire
Alarm Control System
GST5000/8
• Standard EN54 Part 2/4 ; BS5839 Part 4

• Loop Capacity 242 address per loop
• Main Input Voltage 220 ± 10% VAC 50/60 Hz (PSU)
• Input Current Rating 2A
• Operating Temperature 0ºC to +40 ºC at 95% Relative Humidity
• System Operating Voltage 24 VDC Nominal (17-29 VDC)
• Standby Batteries
Twin 12volt Battery (PSU) 12Ah/75AH -Ampere-Hour according to the load
application (Not included)
• 3 Alarm/Sounder Circuits Output capacity
• Output voltage 21VDC to 27 VDC
• Output current: 500mA each output
• EOL 10K resistor
• Fuses Mains 2A (20mm A/S ceramic)
• Sounders (2): 1A (20mm A/S)
• Fire alarm Output 0.5A (20mm A/S)
• Battery: 10A (20mm A/S HRC ceramic)
• Common Fault Relay Output Volt-free changeover (NO/NC) 1.0A at 24 VDC
• 24 VDC Fused Output Maximum load 500mA at 17-28VDC
• Dimension 506mm x 170 mm x 706 mm ( Panel LxWxH))
500mm x 189 mm x 500 mm (PSU box LxWxH)
Selection of GST5000/8 compatible addressable devices and Panels

9 GST200 Intelligent Single Loop Fire Alarm Panels
9 GST5000 Intelligent Modular 2/4 Loops Fire Alarm Panel
9 GST5000 Intelligent Modular 1-20 Loops Fire Alarm Panel
9 GST 9000 Intelligent Modular 1-42 Loops Fire Alarm Panel
9 GST852RP Repeater Panel
9 DI-9100 Series Digital Detectors
9 I-9101 Multi detector
9 I-9102 Optical Detector
9 I-9103 Dual Heat Detector
9 I-9104 UV Flame Detector
9 I-9105R Beam Detector
9 I-9200 Series Manual Call points
9 I-9300 Series Interfaces (Complete range for all requirements
9 I-9400 Series Sounders and strobes
9 I-9600 series Combustible gas detectors
9 Ex Interface series intrinsically safe detectors and sounder
Box
GST5000/8 Intelligent Modular 8 Loops Fire Alarm Control 35 1
Panel
Main Supply and Battery 13 1

Intelligent Modular 1-20
Loops Fire Alarm Control
Description
System GST5000R/C
The GST 5000 is an intelligent fire alarm
control panel. Mounted in either rack or
console type housing it provides the perfect
solution for all medium to large system by
utilizing advance GST Protocol.
The system is compatible with the complete

range of GST Intelligent detectors,
Sounders, Call Points, and Interfaces,
including intrinsically safe and gaseous
extinguishing control. GST 5000 is
manufactured and certified to EN54 parts 2
and 4 and to BS5839 Par 4.

The GST zone indication and control
intervene, with evacuation and control of
equipment under an alarm condition.
Addressable security control facilities and

Features and Benefits gas release control monitoring are built in
as standard.
1. 19” Rack or Console type
2. 20 x Loop capacity (4840) addresses By utilizing the GST protocol the GST5000
3. Colour Graphical LCD Display. can be networked with up to 32 panels, not
4. Multi Zone indication including only the GST200 single loop panel, but also
manual intervention and control with the GST5000 4 Loops panel and the
panel. GST5000 8 loops panel, making this the
5. Networked with all GST Intelligent perfect solution for large decentralized
Fire panels. systems such as Shopping Centers Military
6. Programmable form PC or via on campus industrial complexes, Holiday
board keypad. villages etc.
7. RS485 Repeater Output (Max. 64
Repeaters) With up to 4840 two-wire fire alarm linkage
8. Built-in gas extinguishing control. control points that can also be intelligent be
9. Integrated Security alarm facilities. connected with many serial products (ex.
10. Advanced user friendly programming digital detector, analogue detector,
software including ‘Fuzzy Logic’. intelligent detector, control module and
11. Optional Color Graphics. multi-wire control panel). Therefore this
12. Panel Printer included solution provides a flexible solution for
large building of two-wire and multi-wire
integrated alarm & linkage equipment, GST
5000 intelligent linkage controller is the
best choice for fire protection engineering.

Intelligent Modular 1-20
Loops Fire Alarm Control
System GST5000R/C
• Standard EN54 Part 2/4 ; BS5839 Part 4
• Loop Capacity GST5000/2:480 devices
GST5000/4:960 devices
• Main Input Voltage 220 ± 10% VAC 50/60 Hz
• Input Current Rating 3A
• System Operating Voltage 24 VDC Nominal (17-29 VDC)
• Standby Batteries
Twin 12volt Battery (panel) 40Ah, 24hours
Twin 12volt Battery (PSU) Ampere-Hour according to the load application
• Sounder Circuits (2) Output voltage 17 to 29 VDC
• Output current: 1.0A
• Maximum total load 1.5A
• EOL 10K resistor
• Fuses Mains 1A (20mm A/S ceramic)
• Sounders (2): 1A (20mm A/S)
• Fire alarm Output 0.5A (20mm A/S)
• Battery: 2A (20mm A/S HRC ceramic)
• (Fire alarm) Relay Output 0.5A at 24VDC
• Common Fault Relay Output Volt-free changeover 1.0A at 24 VDC
• 24 VDC Fused Output Maximum load 500mA at 17-28VDC
• Battery Charging Current Limit 600mA
• Dimension 580mm x 520mm x 1873mm ( Rack type)
1080mm x 1113mm x 1350 mm (2bay console)
Selection of GST5000R/C compatible addressable devices and Panels
9 GST200/2 Single or Twin Loops Intelligent Fire Alarm Controller
9 GST5000/2/4 2 to 4 Loops Intelligent Fire Alarm Controller
9 I-9105R Intelligent Beam Detector
9 I-9200 Addressable Series Manual Call points
Box
GST5000R Intelligent Modular 1-20 Loop Fire Alarm 75.00 1
Control Panel ( Rack type)
GST5000C Intelligent Modular 1-20 Loop Fire Alarm 105.00 1
Control Panel (2bay Console type)

LCD Repeater Panel
GST852RP
Features and Benefits Selection of compatible Control Panels

Compatible with all GST Intelligent fire alarm
1. Large LCD Display panel.
2. Back Lit LCD displays all fire
information Ordering Information:
3. Two plug-in constructions allow easy
installation. Part No Description Weight Pack
4. Addressable intelligence enabling full /Kg Qty per
monitoring and reporting to Fire Box
Control Panel GST852R LCD Repeater 0.560 1
Panel
Description
GST852RP LCD Repeater Panel is designed
with a microprocessor. When one or more
detectors alarm fire, the repeater panel can
display the location numbers and information
of the detectors and sends out audible and
optical signals. Through our RS 485
communication network, it can be connected
to all GST Intelligent fire alarm controllers.

• Power Consumption:
Standby power: 2W
Maxi2mA
+50°C
• Material and colour: ABS, Off-white
• Wiring: 2 pair polarized: 1 pair supply MANUFACTURED IN ACCORDANCE WITH
and 1 pair data signal
• Dimensions: 234 x 104 x 35mm

LCD Repeater Panel
GST852RPX
1. Active repeater
2. Silence and reset the panel
3. Back Lit LCD displays
4. Connected to network RS 485
5. Compact size and easy to install
Description
GST852RPX Active LCD Repeater Panel is
design to control and reset the alarm
remotely and display detectors healthy, fire
and fault. This repeater panel can display the
location numbers and information of the
detectors and sends out audible and optical
signals. Through RS our 485 communication
network the repeater can be connected to all
GST Intelligent fire alarm controllers.
Compact size and easy to install. The
repeater can be used whenever there is a
need to relay information to multipoint
informing key personnel.
Compatible with all GST Intelligent fire alarm
panel.
Specifications
t/Kg Qty per
Box
Standby power: 2W
GST852RX LCD Repeater 1.60 1
Maximum: 2mA
Panel
• Display: 4x80 characters
+50°C
• Material and colour: ABS, Off-white
• Wiring: 2 pair polarized: 1 pair supply
and 1 pair data signal
• Dimensions: 230 x 210 x 50 mm

Mimic Panel
GST 8903
1. Miniature and convenience in

installation and operation.
2. Good performance, high-reliability,
and flexible configuration
Description:
GST8903 Intelligent Graphic Repeater

Panel is a fire alarm display unit used in buildings and fire control center. The host controller in
fire control center will give an alarm in case of fire taking place in the building; at the same
time it will transmit the alarm signals to the repeater panel, which locates in fire alarm area.
The repeater panel will show the position of the alarming detector through indicators. The
personnel could be alerted and evacuated out of the fire area.
Specification
• Display Range: 1 up to 100 group code points. The code supports the mode of wildcard
character.
• Display Capacity: There is no more than 100 pieces of fire information displayed by the
repeater panel.
• Wiring: Connected with fire alarm controller with two polarized wires; connected with
power supply with two 24VDC power lines, non-polarized.
• Monitoring Current ≤25mA
• Alarming Current ≤100mA
• Environment Temperature: 0ºC+40ºC
• Relative Humidity: ≤95%, non condensing
• Power: Centralized power supply by 18VDC-28VDC, static state power consumption
≤0.7W, maximal power consumption ≤3W
• Dimension: 380mm×480mm×70mm
• Installation Hole Distance: 260mm
Part No Description Weight/Kg Pack Qty per Box

GST8903 Intelligent Mimic Repeater Panel 0.58 1

Handheld Programmer
P-9910
• Single point programming and

interrogation of GST I-9000 Series
detectors and protocol
• Power supply: one 9V battery
• Working current: ≤8mA
• Standby current: ≤50μA
• Operating environment:
• Temperature: -20oC+70
• Relative humidity: ≤95 % 40±2ºC
• Physical dimensions:
164mm×64mm×24mm
Selection of compatible
Feature Compatible with all GST Intelligent devices
• Portable programming tool for
addressing and testing of intelligent Ordering Information:
devices
• Digital programming Part No Description Pack Qty
• Programs all loop devices (1-242 per Box
addresses per loop) P-9910 Handheld Programmer 1
• Non-polarized 2 wire intelligent
programmer
• Interrogates devices for conditions
• Reprogram facility enables
adjustment to alarm sensitivity of
detectors
• Adjust inputs modules to accept N/C
or N/O contacts
• Low power consumption with sleep
and auto off mode.
• Battery low indication
• Display type: Four-bit LCD
• Easy operation Hand held engineering
tool.
Description
The P-9910 GST protocol programming tool,

capable of reading and writing address codes,
displaying model number, year of
manufacture and batch number, plus display
and adjust analogue sensitivity. Enable to Note: Specifications are subject to change without notice.
adjust alarm threshold, N/C or N/O and
switch on or off the rate of rise of dual heat
detector.

Loop Relay
P-9903
• Operating 24VDC
Voltage
• Loop Input ≤1000m
Distance
• Loop Output ≤1000m
Distance
• Power Voltage 24VDC (18VDC 27VDC)
• Operating ≤50mA
Current in
Empty Load
• Operating ≤200mA
Current in Full
Load
• Load Ability Connecting with 1-150 loop
and devices, compatible with all
Compatibility the loop devices.
• Isolation Isolation voltage between loop
Voltage input and loop output is not
less than 1500V.
• LED Red LED lights when FACP
sends signals.
• Operating Temperature: -10 +50
Environment Relative Humidity: ≤95%, non
Feature condensing.
• Dimension 85mm×128mm×56mm
• Material and Q235A, grayish white
Color of
• Digital communication with fire Enclosure
alarm control panel ensures
immunity to electromagnetic Wiring and Connection
interference and reliable operation. Refer to installation detectors manual.
• Optoisolated output signal,
resistant to industrial frequency 85mm
50mm 56mm
interference.
P-9903
Loop Relay Module
Description
128mm
116mm
M4 Screw
P-9903 Loop Relay Module is 24VDC

powered. The input and output of loop
signal are insulated to ensure transmission Cable Length ¡ 1
Ü000m
of detector signal which enhances

Z1IN Z2IN
Z1o Z2o
P-9903
interference-resistant ability of the system

LOOP
24VIN 24VIN
and prolongs the loop distance. +24V Loop Device Loop Device
P-9903 is mainly used in applications where

GND
strong electromagnetic interference exists

or where the loop needs to be extended to
longer than 1000m. Part No Description Weight Pack
The relay module consists of a transmitter /Kg Qty per
Box
circuit, a receiver circuit, and an isolated
P-9903 Loop Relay 0.82 1
power supply. Optocoupler isolation MANUFACTURED IN ACCORDANCE WITH
technology is used between the

transmitter and receiver circuit.

Loop Splitter
P-9902
1. Providing an additional loop

interface
2. Increase the loop length
3. Installed inside the panel
Description
The GST Loop Splitter is used for additional
loop interface for the control panel without
affecting the loop configuration.
Terminals
z Input Side (XT1, XT3 & XT4)
XT1 (Zin+ & Zin-): Loop from
loop card
XT3 (24+ & 24-): 24VDC in
XT4 (24+ & 24-): 24VDC out
z Output Side (XT2)
ZO+ & ZO-: Ordering Information:
Loop Out
/Kg Qty
ZI+ & ZI-: per
Loop In Box
P-9902 Loop Splitter .003 N/a
System Connection
The system should be connected as below.
Loop Splitter
Sub-Loop 1
24VDC
Splitter Sub-Loop 2
Splitter Sub-Loop 3
Note
z The splitters are programmed by P-
9910B handhold programmer, taking
individual addresses on the loop.
Special program should be applied on the
panel.

Graphic Monitor
Center GSTGMC2.0
Feature
• Colour graphic control and display

system
• Complete window onto the fire
detection system and ancillary
equipment
• Multi-level password control for
convenient system management
Description
The new developed GSTGMC2.0 Graphic
Monitor Centre is the new developed software.
With friendly interface, the software may
support 8 client stations plus local monitor
station, making complete monitoring and
control. Also with Open Protocol
Communication (OPC), the communication
with panel can also be integrated into other
systems. The related panel types include Selection of compatible Control Panels
GST200, GST500 & GST5000. The main Compatible with all GST Intelligent fire alarm
features of this highly intelligent package are: panel.
The self-reacting communication module
automatically maintains data communication Ordering Information:
with panel. The operator can test the
communication at any time to ensure the Part No Description Pack Qty
reliable running of system per Box
The communication server connects to panel GSTGMC Graphic Monitor CD
directly. The monitor stations can be set Centre
locally or through LAN or even through WAN. P-9931 RS 232 1
Multi-level password control Communication Board
Simple, direct and complete user graphics
view interface, switching between device
layouts of different monitoring zones.
Pop out layout of abnormal information
automatically. Flash the abnormal device(s)
in different colours for alarm, plant, fault and
isolation.
Complete functions of database management
and data copy ensure system safety by
minimizing possibility of data loss.
System Requirement
Hardware
CPU: Pentium III 600 or Higher
Minimum free Hard disk:2GB MANUFACTURED IN ACCORDANCE WITH
Memory:128MB
Software
Windows 98SE, Windows 2000 or Windows
XP Professional

Fire System OPC
Server GSTOPC
Feature System Requirement
• Open Protocol Communication Server Hardware

for Fire Alarm System CPU: Pentium III 600 or Higher
• Complete data information onto the Minimum free Hard disk: 2GB
fire detection system and ancillary Memory: Minimum 128MB
equipment such as Normal, fire, fault, Serial Port
isolation and start device Software
• Work on GSTGMC2.0 server Supported all MS window Operating System
• Compatible with all GST Intelligent Windows 98SE, Windows 2000 or Windows XP
Fire Control Panel Professional
• Compatible on latest Operating
system
• Multi-level password control for
convenient system management
Description
The GSTOPC Fire Alarm OPC Server is the
new developed software communication with
panel can be integrated into other systems
and Building Management System. The
related panel types include GST200 and
GST5000 series. The main features of this
highly intelligent package are:
The self-reacting communication module
automatically maintains data communication
with panel. The operator can test the
communication at any time to ensure the
reliable running of system through GSTGMC
2.0 Server. Selection of compatible Control Panels
Ensure easy and uniform integration of Compatible with all GST Intelligent fire alarm
subsystem from different manufacturer and panel.
open Building Management System.
The communication server connects to panel Ordering Information:
directly. The monitor stations can be set
locally or through LAN Part No Description Pack Qty
Multi-level password control per Box
Display of information automatically for GSTOPC Fire Alarm OPC Server CD
modules, sounders and sensor GSTGMC Graphic Monitor CD
GSTOPC code tag 0-ok, 1-isolate, 2-alarm, 3- Centre Server
Action,4-fault, 5-start, 6-stop, 7-release, 8- P-9931 RS 232 1
restore, 9-mute, 11-reset, others-panel Communication Board
disconnect.
Complete functions of database management
and data copy ensure system safety by MANUFACTURED IN ACCORDANCE WITH
minimizing possibility of data loss.

Fire Alarm Monitoring
& Management System
GST911 AlarmNet
• Fire alarm monitoring server

• Voice and time recording system
• Received alarm message within a
second
• Dynamically display messages and
geography simultaneously on twin The GST Alarm Net enables complete
screen control over remote fire control panels in
• User management system real time. Including the silencing, isolating
• Monitoring status of individual fire and de-isolating of devises, operation of
alarm system. plant equipment, interrogation of individual
• Support different type of detectors analogue value plus much more.
transmission media such as LAN / Each control panel connected to the
WAN/ TCP/IP,VPN, GSM , PSTN network takes individual IP address. The
• Multi-level Password protected control centre is based on a computer
• Interface with all GST Intelligent utilizing Microsoft Windows. All signals are
Panel transferred directly through network
• Transmission line monitoring transmission, therefore overcoming any
• LCD display and LED indicator distance limitation that can be found in a
standard fire alarm network solution.
Description At the control centre, when the fire signals
comes in, firstly the local warning alarm will
GST alarmNet System is specially designed
sound, or digital voice message will
for long distance fire alarm network broadcast, simultaneously, the geography
solutions over a LAN WAN, GSM, VPN or
map will show the location of the project.
PSTN. The system was originally developed
Also the detail site drawing can be shown
for a central monitoring of specialist manually with a simple click of a mouse,
application such as remote telecom station,
indicating the floor plans with exact location
remote railway stations, petrochemical pipe
of the detector in alarm.
pumping station, unnamed remote facilities
Multinational institutions and hotel chains
and for central monitoring services
providers and fire brigade control centres.

Fire Alarm Monitoring
& Management System
GST911 AlarmNet
Fire Alarm Monitoring System
Selection of GST AlarmNet compatible Communication Interface
9 GDZ-6Y PSTN Communication Interface

9 GST2000 LAN WAN/TCP/IP Communication Interface
9 GST800 LAN WAN/TCP/IP/ GSM Communication Interface

Box
GST911 Fire Alarm Monitoring and Management CD 1
AlarmNET Software

Fire Alarm
TeleNetwork Interface
GDZ-6Y
• Auto Dialing to the GST AlarmNet

Centre
• Automatic Alarm/fault report to the
central monitoring
• Password protected
• Can store up to 6 telephone number
• With local telephone auxiliary
• Override telephone conversation
when alarm
• Telephone line monitoring
• Can store 9 second voice message
• Utilized speaker for local alarming
• 10 characters LCD display
• LED indicator
• Backup battery with built-in charger Specification
• Operation voltage: 220VAC /50HZ,
12VDC
Description • Telephone Line Feeding Voltage: -54V ∼
-44V
GDZ-6Y Fire Alarm Tele-Network Interface • Telephone Line Feeding current: 18mA ∼
can be programmed directly by telephone 50mA
(Line will not be occupied), or by remote • Power Supply Capacity of Detector
programming with a telephone from other Connected: 12VDC, Maximum: 150mA
lines. There are six independent • Standby Battery: 12VDC /7Ah lead-acid
programmable protective zones and each storage battery
protective zone can be programmed as 24- • Alarm Output: 12VDC, Maximum:
hour or delay protective zone. Six telephone 150mA
numbers are stored inside and the former • Dialing and Data Transmitting Mode:
three are used for fire fighter and the other DTMF Code
three are used for management. Once the • Power Consumption: < 10W
fire alarm in protective area is triggered on, • Operation Temperature: 0ºc∼55 ºc
the tele-network interface will dial the fire • Relative Humidity: 10%∼75%
protection bureau or central monitoring .The
voice, fire condition, protective zone number
and user address codes are distinct among
the different protective zones. One alarm
output is provided in the delay protective
zone.

Fire Alarm
TeleNetwork Interface
GDZ-6Y

Compatible with all GST Fire alarm panel and interfacing to existing conventional panel or other fire
alarm system from other manufacturer.
Part No Description Pack Qty per Box

GDZ-6Y Fire Alarm TeleNetwork Interface 1

Intelligent Alarm Card
D081A
Description
D081A Intelligent fire alarm board for PSTN up to 4 telephone line input.
Specifications
• Interface type: Relay
• Port Resistance: 600Ω
/Kg Qty per
• Frequency Range: 300~3.4Khz
Box
• Compatible PC: PCI slot of Pentium 1
D081A Intelligent 1.20 1
or above
Alarm Card
• Cache on board: 64Kb, 16Kb for
voice
• Digital Voice: ADPCM
• Baud Rate: 64kbps, 32 kbps
• Sampling Rate: 8K
• Volume Control: -20dB to +50db
• Signaling: DTMF
• Dialing Monitor: Dialing tone/Reverse
Polarity
• Modulation type 1: 1.2Khz±1%
• Modulation type 2: 2.2Khz±1%

• Data Transfer: Binary Asynchronous
Serial Transfer

Fire Alarm Transmitting
Equipment
GST2000
Description
The GST2000 Fire Alarm Transmitting
Equipment (FATE) can receive and monitor
fire alarm information from GST Fire
controllers and then report to the Central
office where GST-911Net fire alarm
monitoring and management system is
installed utilizing different transmission
protocol such as LAN/WAN/TCP/IP. The
range of GST intelligent panel. The FATE
enables total monitoring like serial port
disconnection and controller failure.
Support alarm sound and voice recording
including manual/automatic answer on duty
host computer. Easy to programme and
install.
• Auto reporting to the GST Alarm

Net Center via TCP/IP
• Automatic report to the central
monitoring with full information
including the location of devices.
• Support Video/Audio Transmission
• Support RS 232 or RS 485
communication
• Password protected
• Interface with all GST Intelligent
Panel
• Transmission line monitoring
• Serial interface monitoring
• Locking enclosure, power supply
and battery space included
• Built-in non-volatile memory to
protect data upon power failure.
• 40 x 4 Character LCD display and
LED indicator
• Backup battery with built-in charger

Fire Alarm Transmitting
Equipment
GST2000

Operating Temperature -10°C to 50°C
Relative Humidity 95%, no condensation
Power Requirement 12 VDC Nominal
Standby Battery 12VDC, 7.) AH Lead Acid cell for 20Hrs
Network 10/100 base -LAN/WAN
Protocol TCP
Serial Port DB9 (RS 232, Optional RS 485)
Mounting Wall Mount
Case Materials and Colour DC
Dimension 520 X 370 x 110 mm, LWH
Selection of GST2000 FATE compatible addressable panels
9 GST100 Addressable Mini Fire Alarm Controller

9 GST200/T Single Loop Intelligent Fire Alarm Controller
9 GST5000/2/4 2/4 Loops Intelligent Fire Alarm Controller

Box
GST2000 Fire Alarm Transmitting Equipment 13.05 1

Intelligent Boxed PSU
PSU24-3(3A)
The PSU applies AC220V as its primary power

and sealed lead-acid battery as standby power.
In case of commercial power failure, it can
automatically switch to standby power. Applying
switched power voltage stabilizing circuit and
standby power float charging circuit, it has the
functions of automatic over-current protection,
switch between primary and standby power, and
automatic charge and over-discharge of standby
battery.
PSU24-3A can also report fault signals from

primary and standby power to controller through
non-polarized two-wire, solving the problem that
field powered high current devices cannot be
activated as a result of voltage-drop of powering
line.
1. 3 Amperes/ 24 volt DC Intelligent

PSU
Compatible with all GST products.
2. Fully Monitored with self test facilities
3. Display AC input voltage, DC output
voltage and DC load (Amp)
4. Addressable intelligence enabling full
monitoring and reporting to Fire
/Kg Qty
Control Panel
per
Box
Description PSU24-3 Intelligent 4.56 1
Boxed PSU
PSU24-3 Intelligent PSU and PSU24-3A
PSU24-3A Intelligent 5.48 1
Intelligent Network PSU are used together
Network
with the controller to power connected
Boxed PSU
controlling module and controlled devices.
Specification
Part Number PSU24-3A PSU24-3
Output capacity Rating: 24Vdc/ 3A
Power Supply Primary:220Vac ±15%; Standby:2x12Vdc/7A sealed lead acid
Electronic programming with 1~242,
Addressing Mode No Feature
occupying 1 address
Colour Ivory white

Intelligent Boxed PSU
PSU24-6(6A)
The PSU applies AC220V as its primary power

and sealed lead-acid battery as standby power.
In case of commercial power failure, it can
automatically switch to standby power. Applying
switched power voltage stabilizing circuit and
standby power float charging circuit, it has the
functions of automatic over-current protection,
switch between primary and standby power, and
automatic charge and over-discharge of standby
battery.
PSU24-6A can also report fault signals from
primary and standby power to controller through
non-polarized two-wire, solving the problem that
field powered high current devices cannot be
activated as a result of voltage-drop of powering
line.
1. 6 Amperes/ 24 volt DC Intelligent

PSU Selection of compatible Control Panels
2. Fully Monitored with self test facilities Compatible with all GST products.
3. Display AC input voltage, DC output
voltage and DC load (Amp) Ordering Information:
4. Addressable intelligence enabling full Part No Description Weight Pack
monitoring and reporting to Fire /Kg Qty
Control Panel per
Box
PSU24-6 Intelligent 10.46 1
Description
Boxed PSU
PSU24-6 Intelligent PSU and PSU24-6A PSU24-6A Intelligent 10.46 1
Intelligent Network PSU are DC24V large Network
capacity field power output equipment, used Boxed PSU
together with the controller to power
connected controlling module and controlled
devices.
Specification
Part Number PSU24-6A PSU24-6
Output capacity Rating: 24Vdc/ 6A ; Max: 24Vdc/ 8A
Power Supply Primary:220Vac ±15%; Standby:24/24Ah (maximum capacity) sealed lead acid
Electronic programming with 1~242,
Addressing Mode No Feature
occupying 1 address
Colour Ivory white

Gas Extinguishing
Control Panel GST301
Primary and Standby cylinder key switch,
that enables quick and easy transfer to the
reserve cylinders, thus to ensure that the
area can be left protected after an
evacuation.
The pre release gas countdown timer

display on the panel to shows the amount
of time left (in seconds) before the gas will
be released, this is adjustable from 0- to 90
seconds, (all panels are sent factory set at
30 seconds delay).
• Operating voltage:220VAC +/- 15%

• Battery Requirement:2X12VDC,
Features and Benefits 7AH
• Battery operating time: 24 hours
monitoring and half hour alarm
1. Double Knock Extinguishing Fire • AUX power supply:100mA/24VDC
Zones • Sounder output:1A/24VDC
2. Aux. (non Extinguishing) Fire Zone. • Release output: 2A/24VDC, pulse
3. Automatic and Manual extinguishing • Temperature: -10°C ~ 55°C
control • Humidity: ≤95%
4. Numerical Onboard Timer Control • Dimension:250X300X130mm
5. Adjustable Gas release delay Timer
6. Duty and Standby Cylinder control
7. Two phase evacuation sounders
8. Adjustable Solenoid Pulsed output
9. Compatible with all GST conventional
detectors Selection of compatible system
10. Fully compliant to BS /EN /CE
9 GST Conventional Fire Detector
9 GST Conventional Sounder and Bell
9 C-9317 Emergency Start/Abort
Description Switch
9 C-9318 Gas Extinguishing Warning
The GST301 conventional gas extinguishing Indicator
control panel is packed with unique features 9 GST- Conventional Panel
that you have come to expect from a GST
product that have enabled us to become Ordering Information:
world recognized as a leading manufacturer
in the fire detection industry. Part No Description Weight Pack
/Kg Qty
per
The system provides 3 fire detection zones, Box
two of which are utilized for double knock gas GST 301 Conventional 3.09 1
extinguishing control, and a third Auxiliary Gas
fire detection zone for additional areas out Extinguishing
side of the gas protected area. This Zone will Control Panels
operate as a normal fire detection zone and
have no interaction with the gas release
system.

Addressable Gas
Extinguishing Control
Panel GST303/306
It can also control gas release devices
independent of the FACP. When the FACP is
not working properly, it can still control
extinguishing devices through emergency
gas override control in field or Start and
Stop keys on the control panel. This control
panel can check the circuit and alarm when
circuit is open or shorted.
• Capacity: GST303 Maximum 3

extinguishing zones ; GST306
Maximum 6 extinguishing zones
• Delay Time: 0s to 45s, adjustable by
every 5s
• Wiring: Connecting to the FACP by two-
Features and Benefits 2core cable. 2-core cable to the
solenoid of cylinder, pressure switch
1. Compatible with all GST Intelligent and gas extinguishing warning indicator.
Control Panel. Connecting with emergency gas
2. Sits directly on addressable loop override control by 3 cores. Connecting
3. Direct intelligent control via with sounder strobe by two-wire.
addressable loop • Power supply: 24VDC~28VDC from
4. Capable of controlling up to six zones intelligent PSU, total length from PSU to
of extinguishing the control panel and from the control
5. Automatic and Manual control panel to solenoid should not be over
facilities 100m, cross section not less than
6. Utilises GST intelligent detectors and 2.5mm2.
programming Fuzzy Logic control • Solenoid Interface: Start output: By
7. Fully monitored status control pulse or electric level mode. 5s for
8. Duty and standby Cylinder Control pulse mode; Voltage range: 18VDC-
9. Required 24VDC Power Supply 26VDC; Maximum current: 2A
10. LED status indicator • Gas Extinguishing Warning Indicator
Interface: Start output: Voltage range:
Description 18VDC 26VDC; Maximum current:
300mA Load: Maximum 5 for each zone.
• Sounder Strobe Interface: Passive
The GST303 and GST306 addressable gas
contact output; Maximum current
extinguishing control panel is packed with
allowed: 1A
unique features that you have come to
• Emergency Gas Override Control: Load
expect from a GST product that have enabled
Maximum 5 for each zone.
us to become world recognized as a leading
• Standby Power Consumption≤10W
manufacturer in the fire detection industry.
• Operating Environment
Temperature: 0°C+40°C
The system provides up to 6 extinguish zones,
Relative Humidity≤95%, non
connected directly on the addressable loop
condensing
Auxiliary, the FACP that are able to control
• Dimension:
associated fire suppressant equipment to
GST303: 385mm×444mm×149mm
achieve automatic or manual control of gas
GST306: 575mm×444mm×149m
release.

Addressable Gas
Extinguishing Control
Panel GST303/306
Mounting
Wall mounting installation dimension
Installation Hole
Installation Hole
Knock off the Wiring Hole

Knock off the Wiring Hole
Wiring Diagram
Connect the wires to the required terminal Selection of compatible system

must be fire rated type and the size depends 9 GST Intelligent Fire Alarm Control
on the distance and application. Connection Panel
to the FACP by two-2core cable, 2-core cable
to the solenoid of cylinder, pressure switch Ordering Information:
and gas extinguishing warning indicator.
Wiring connection to emergency gas override Part No Description Weight Pack
control required 3 cores and sounder strobe /Kg Qty
by two-wire. Refer to the user manual for per
Box
more information.
GST 303 3 Zone 6.8 1
Addressable Gas
L1 L1 L2 L1 L2
Extinguishing
G G C- 9317 G G C- 9317 G
4.7K¦ ¸
4.7K¦ ¸
Control Panels
L3 L3 L4 L3 L4
GST 306 6 Zone 7.3 1
Addressable Gas
Extinguishing
DC1+ DC1+ J11
Solenoid of Cylinder
DC1- DC1- J12
Control Panels
C- 9329
YK1 YK1 K11
Pressure Switch
Extinguishing Control Panel
YK2 YK2 K12
COM
Driving device Solenoid of Cylinder
NO controlled by a
contact
R R1 R2 R1 R2
C- 9318 C- 9318 4. 7K¦ ¸
GND G1 G2 G1 G2
K1
K2
G S G S G S
I - 9403 I - 9403 I - 9403

D1 D2 Z1 Z2 D1 D2 Z1 Z2 D1 D2 Z1 Z2
+24V
GND MANUFACTURED IN ACCORDANCE WITH

Z1
Z2
Zone 1

Emergency Start/
Abort Switch C-9317
• Operating voltage: 19Vdc (14Vdc to
22Vdc) polarized
Standby: 0.0mA; Alarm: 25mA
+50°C
• Output Capacity: Rating 60VDC,
0.1A,Normally Open
• Contact resistance: ≤100mΩ
• Reset Mode: Manually reset by a
sucker
• Indicators:
Start: Red, constantly lit when
pressed
Stop: Red, constantly lit when
pressed
Features and Benefits • Application: Indoor use
• Material and colour: ABS, Red
1. Emergency start/abort switch for gas • Wiring: 3 pairs polarized
extinguishing control • Dimensions:
2. With Output passive normally open 144mm×90mm×58.5mm
contact
3. Glass protected Wiring and Connection
4. LED indicator
5. Compatible with GST series of gas Connect the wires to the required terminal
extinguishing control panel according to the label. The cable must be
fire rated type and the size depends on the
distance and application. Minimum size
Description gauge 1.0mm²(18 AWG). See installation
C-9317 Emergency Gas Override Control is and operation for more information.
used to control the start and stop of gas
extinguishing system. When fire occurs in its
protected area, press emergency start button, Mounting K1 L1+ G L2+ G Mounting
messages can be sent to gas extinguishing Hole Hole
control panel, which will give gas
extinguishing command and start the
solenoid after delay. During the delay time, if
people in field can confirm there is no fire, he
could press the emergency stop button. The
contact closes when the start button is
pressed, and it's open when the stop button
is pressed. Both the start and stop button
K2 L3+ G L4+ G
are self-lock buttons.

Compatible with all GST Conventional and Part No Description Weight Pack
/Kg Qty
Addressable Gas Extinguishing Control
per
System. Box
C-9317 Emergency 0.313 1
Start/ Abort
Switch
`

Gas Extinguishing
Warning Indicatior
C-9318
28Vdc) polarized
• Operating Current: Alarm: 100mA
+50°C
• Indicators: 16 Highlights Red LED,
constantly lit when alarm
• Material and colour: ABS, Red
• Dimensions: 280m×110mm×46mm
Features and Benefits Wiring and Connection
1. Normally installed above the entrance Connect the wires to the required terminal
to a gas extinguishing control area. according to the diagram. The cable must
2. Will eliminate and activate internal be fire rated type and the size depends on
sounder prior to gas release. the distance and application. Minimum size
3. "Gas Extinguishing DO NOT ENTER" is gauge 1.0mm²(18 AWG). See installation
printed on the panel of the indicator. and operation for more information.
4. Highlight LED
5. Compatible with GST series of gas
extinguishing control panel
1 PAIR FIRE CABLE
Description
Gas Gas
C-9318 Gas Extinguishing Warning Indicator

G1 R1
G2 R2
G1 R1
G2 R2
XT1 XT1
DO NOT XT2 DO NOT XT2
is the accessory equipment of a gas

extinguishing system. It's usually installed at GAS
EXTINGUISHING
WARNING INDICATOR A WARNING INDICATOR B
the entrance of the protected area. After gas CONTROL PANEL
is released, the controller will activate the

indicator to give visual indication warning
people in field to take relative measures. G1, R1 (XT1): To DC24V or GND, R
This indicator is non-addressable and is used terminal of extinguishing
together with extinguishing control panel. control panel, polarized.
G2, R2 (XT2): Connecting with gas
extinguishing warning
indicator in series or with
4.7kΩresistor.
Compatible with all GST Conventional and
Addressable Gas Extinguishing Control
System.
/Kg Qty
per
Box
C-9318 Gas 0.850 1
Extinguishing
Warning
Indicator

Innovative Conventional
Optical Smoke Detector
DC-9102 Technical Specifications
voltage
Alarm Current 1.8mA
• Operating temp: -10°C to +50°C
than 6m, 80 sqm less than 6m
• Visual Indicator: LED, Red ( lit steady
1. Built in microprocessor
2. Built in magnetic test switch
4.45cm
3. Algorithm maps for faster response and
false alarm rejection
Installation and wiring
4. With drift compensation to ensure
Suitable for surface mount only, mount on
constant sensitivity
standard 1gang electrical back box with a
mounting hole of 45mm to 75mm spacing.
proof ability and LED for 360º vision
6. Built in remote indicator output
7. Unique Low profile design
8. EN54 compliance
gauge 1.0mm²(18 AWG).
Description
The DC-9102 Innovative Conventional Optical
Smoke Detector is the ideal device for most
application due to its excellent digital response
to a wide variety of different type of smoke
patterns. The unit meets the sensitivity
requirement of EN 54 part 7, European
Standard Unique and pleasing with a low profile
Using active end of line can connect up to 15
detectors and base with diode.
intelligent processor that provides digital
signaling. The integral microprocessor analyses
the signal according to integrated algorithm of
analyzing fire, then confirms these pattern with
the pre-programmed fire scenarios and smoke
patterns for a faster and safer response.
Using 4.7KΩ end of line resistor can connect
up to 25 detectors
Compatible with all GST Conventional panel
and GST Intelligent Fire Alarm Panels using
Part No Description Weight Pack Qty
Zone monitor module: /Kg per Box
DC-9102 Innovative 0.110 120
Conventional
Optical Smoke
Detector
DB-01D Base with Diode 0.049 360

Innovative Conventional
Dual Heat Detector DC-9103
voltage
Alarm Current 1.8mA
+50°C
• Detecting range: 30 sqm for normal
area; and 20 sqm for high risk
Features and Benefits • Dimensions: diameter 10cm; height
1. Built in microprocessor 4.45cm
2. Built in magnetic test switch
3. Algorithm maps for faster response and Installation and wiring
false alarm rejection Suitable for surface mount only, mount on
4. With drift compensation to ensure standard 1gang electrical back box with a
constant sensitivity mounting hole of 45mm to 75mm spacing.
5. Built in remote indicator output Connect the wires to the required terminal
6. Unique Low profile design according to the wiring diagram. The cable
7. EN54 compliance must be fire rated type and the size depends
Description gauge 1.0mm²(18 AWG).
DC-9103 Innovation Conventional Dual Heat
Detector is GST’s new generation fire detection
product. The detector adopts advanced digital
technology and self-diagnostic technology,
which greatly improve detector response rate
and make the maintenance more convenience.
DC-9103 has rate of rise and fixed temperature Using active end of line can connect up to 15
mode. The rate-of-rise feature detects intense detectors and base with diode.
fires by quickly responding to rapid
temperature increases. The fixed temperature
feature reacts to fires when a specific
temperature is reached.
Selection of compatible Control Panels Using 4.7KΩ end of line resistor can connect
Compatible with all GST Conventional panel up to 25 detectors
Zone monitor module: Ordering Information:
t/Kg Qty per
Box
DC-9103 Innovative 0.110 120
Conventional
Dual Heat
Detector
DB-01D Base with Diode 0.049 360

Conventional
Combined Smoke and Detector Installation
Heat Detector C-9101 It is installed onto a standard one gang
electrical box with a mounting hole that
have 6.5cm spacing. Point the detector in
the base by the mark-line and secure the
detector in that position by rotates it

HOLDING PAD
MARK−LINE 2ND MARK−LINE
LED INDICATOR

ROTATE CLOCKWISE
1. Multifunctional and highly reliable Wiring and Connection

detector Connect the wires to the required terminal
2. Sensing chamber for exceptional dust according to the wire diagram with
proof ability matching active end of line (P-9907).and
3. Twin LED for 360º vision (DZ-03D) required base. Using active end
4. Low profile design of line can connect up to 15 detectors and
base with diode. Using 4.7KΩ end of line
Description resistor can connect up to 25 detectors.
I-9101 is a multifunctional and highly reliable The cable must be fire rated type and the
detector that able to sense fire cause by size depends on the distance and
polyurethane and heptanes fire. And also application. Minimum size gauge
detect fire with obvious rise of temperature 1.0mm²(18 AWG)
such as alcohol fire. With all the combined
features of standard optical and heat detector CONVENTIONAL
+
PANEL
1 2 1 2 1 2
makes this suitable for application in data

−
OR
ZONE
processing area like computer room and MONITOR
MODULE
telephone exchange.
4 3 4 3 4 3
P−9907 ACTIVE
END OF LINE
Technical Specifications C−9102 SMOKE DETECTOR C−9101 SMOKE/HEAT DETECTOR
• Standard: EN54-part5, part6, part7

• Protection rating: IP 22 Ordering Information:
• Detecting Range:30m² Part No Description Weight/ Pack Qty
• Operating voltage: 24Vdc (9Vdc to Kg per Box
24Vdc) polarized C-9101 Conventional 0.123 120
• Operating Current: Combined Optical
• Standby: 0.1mA; Alarm:30mA Smoke and Dual
Heat Detector
• Operating temperature: -10~50°C
DZ-03 Detector Base - 0.05 360
EOLR
• Application: Indoor use DZ-03D Base with Diode 0.05 360
• Material and colour: ABS, off-white AOL
height 5cm

Zone monitor module:

Conventional Optical
Smoke Detector C-9102 Detector Installation
HOLDING PAD
LED INDICATOR
Features and Benefits ROTATE CLOCKWISE

proof ability Wiring and Connection
2. Built-in Remote Indicator Output Connect the wires to the required terminal
3. Twin LED for 360º vision according to the wiring diagram. Using
4. Low profile design active end of line can connect up to 15
detectors and base with diode. Using 4.7KΩ
Description end of line resistor can connect up to 25
detectors.The cable must be fire rated type
With the technique of scattering, the and the size depends on the distance and
detector's reliability, stability and consistency application. Minimum size gauge
are improved. The special chamber design 1.0mm²(18 AWG).
ensures the insert-defend, dirt-defend and
anti-light disturbance. CONVENTIONAL
+
PANEL
The conventional type can be used directly 1 2 1 2 1 2
−
OR
with our conventional fire alarm panels. ZONE

MONITOR
MODULE
Using an interface (I-9319), it can be 4 3 4 3 4 3
connected to our intelligent panels. P−9907 ACTIVE

END OF LINE
C−9102 SMOKE DETECTOR C−9101 SMOKE/HEAT DETECTOR
• Standard: EN54-part7 C−9314P Remote Indicator
•
•
Approval: LPCB,UL,CE
Protection rating: IP 32
− +
• Detecting Range:80m² at 6-12meter
ceiling height; and 60m² below 1 2
6meter
TO NEXT DEVICE
• FROM CONTROL PANEL
1 PAIR FIRE CABLE
HOLE
1 PAIR FIRE CABLE
• Operating voltage: 24Vdc (9Vdc to 4 3

24Vdc) polarized
HOLE
Stanby: 0.1mA; Alarm:8mA
• Operating temperature: -10°C to Ordering Information:
+50°C Part Description Weight Pack Qty
• Relative humidity: 95% No /Kg per Box
• Application: Indoor use C-9102 Conventional Optical 0.12 120
• Material and colour: ABS, off-white Smoke Detector
• Wiring: 1 pair polarized DZ-03 Detector Base -EOLR 0.05 360
DZ-03D Base with Diode AOL 0.05 360
5cm


Conventional Dual
Heat Detector C-9103 Detector Installation
HOLDING PAD
Features and Benefits LED INDICATOR
1. Fixed Temperature and Rate of Rise ROTATE CLOCKWISE

Detection
2. Built-in Remote Indicator Output Wiring and Connection
3. Twin LED for 360º vision Connect the wires to the required terminal
4. Low profile design according to the wire diagram with
matching active end of line (P-9907).and
Description (DZ-03D) required base. Using active end
C-9103 Conventional Rate of Rise and Fixed of line can connect up to 15 detectors and
Temperature Heat Detector (hereinafter base with diode. Using 4.7KΩ end of line
called the detector) checks ambient resistor can connect up to 25 detectors.
temperature with the sensitive feature of The cable must be fire rated type and the
thermo-sensitive elements. With a built-in size depends on the distance and
SCM, it’s fixed with highly reliable fire judging application. Minimum size gauge
program. Special processing technology 1.0mm²(18 AWG)
ensures its stable and reliable operation.
Matching with P-9907 Active End of Line Unit, CONVENTIONAL
+
PANEL
1 2 1 2 1 2
it can connect with compatible fire alarm

−
OR
ZONE
controller to conduct the processing of MONITOR

MODULE
4 3 4 3 4 3
detector signals. P−9907 ACTIVE

END OF LINE
C−9103 HEAT DETECTOR C−9103 HEAT DETECTOR
C−9314P Remote Indicator
•
•
Standard: EN54-part5,part6
Approval: LPCB,CE − +
• Detecting Range: 30 sqm for normal 1 2
area; and 20 sqm for high risk

• Operating voltage: 24Vdc (9Vdc to FROM CONTROL PANEL
1 PAIR FIRE CABLE
HOLE
TO NEXT DEVICE
1 PAIR FIRE CABLE
24Vdc) polarized
• Operating Current: HOLE 4 3
• Stanby: 0.8mA; Alarm: 1.4mA

+50°C Ordering Information:
• Relative humidity: 95% Part No Description Weigh Pack Qty
• Application: Indoor use t/Kg per Box
• Material and colour: ABS, off-white C-9103 Conventional Dual 0.123 120
• Wiring: 1 pair polarized Heat Detector
DZ-03 Detector Base -EOLR 0.05 360
DZ-03D Base with Diode AOL 0.05 360
height 5cm MANUFACTURED IN ACCORDANCE WITH


Conventional
Ultraviolet Flame C-9104
The combination of fire detection should be
installed complied with all local codes and /
or NFPA 72 National Fire Alarm Code, NFPA
70 National Electrical Code. Verify the
proper wiring and base is firmly mounted to
prevent detector damage before the
installation. Point the detector in the base
by the mark-line and secure the detector in
Features: that position by rotates it clockwise until it
reaches the next mark line.
1. Not sensitive by sunlight
2. Dust /corrosion/humidity resistance CONCRETE PAD OR
HOLDING PAD
EMBEDDED BOX

4. Standard calibration set to detect a
3cm flame at 6metres MARK−LINE 2ND MARK−LINE
5. Effective range 12 metres

6. 110º effective detection dispersion
angle LED INDICATOR
7. Twin LED for 360º vision ROTATE CLOCKWISE
Description: Wiring and Connection

The C-9104 Conventional Ultraviolet Flames according to the wire diagram with
Detector is fast and capable to detecting the matching active end of line (P-9907).and
ultraviolet (UV) rays emitted by a burning (DZ-03D) required base is The cable must
substance and is used in high hazard be fire rated type and the size depends on
applications such as petrochemical plants, the distance and application. Minimum size
munitions factories and other areas where gauge 1.0mm²(18 AWG)
flammable or explosive liquids or solids are
handled or stored. The C-9104 sensor adopts
an ultraviolet photosensitive tube, with
CONVENTIONAL
+
PANEL
1 2 1 2 1 2
qualities of highly sensitive, reliable, dust-

−
OR
ZONE
MONITOR
resistant, corrosion-proof and moisture- MODULE

4 3 4 3 4 3
resistant, therefore is not sensitive in sunlight, P−9907 ACTIVE

END OF LINE
dust, oil, tolerance of fume, and humidity. C−9102 SMOKE DETECTOR C−9101 SMOKE/HEAT DETECTOR
Technical Specifications Part No Description Weight Pack
• Protection rating: IP 32 /Kg Qty per
Box
C-9104 Conventional 0.123 120
• Operating Current: Ultraviolet Flame
Standby current 1.5mA Detector
Alarm Current 10mA DZ-03 Detector Base -EOLR 0.05 360
• Operating temp:-10°C to +50°C DZ-03D Base with Diode AOL 0.05 360
• Detection angle: 80 degree

when alarm
• Material and colour: ABS, off-white Note: Specifications are subject to change without notice.
5cm

Conventional
Reflective Beam
Detector C-9105R
With built-in intelligent microprocessor, the
detector has strong ability of analysis and
judgment. The detector is ideally suited to
historical buildings, warehouses, large
storages, shopping malls, leisure centers,
exhibition halls, hotel lobbies, printing
houses, clothing factories, museums and
prisons, as well as places where slight
smoke particles or corrosive gas exist.
• Standards: BS EN54 Part-12
• Protection Rating: IP20*
(IP 66 thru glue seal)
• Operating Voltage
Power Voltage: 24Vdc (±10%)
Loop Voltage: 24Vdc
• Operating Current
Features and Benefits Standby current: 12mA
Alarm current: 22mA
1. Wide monitoring area, range 8-100 • Length of Optical Pathway:
metres o 8-100meter
2. Combination of the emitting and • Monitoring width: 14m
receiving parts makes mounting easy • Monitoring Area: 1400m²
and optical pathway accurate • Commissioning Tools: Magnet
3. Simple and cost effective to install • Operating Temperature:
transmitter and reflective ‘honey -10°C to +50°C
comb’ mirror. • Relative humidity: 95%
4. Quick and easy to set up visual • Application: Indoor use
strength indication. • Material and Colour: ABS, Gray
5. Build-in microprocessor • Wiring: 1 pair -24Vdc, 1pair- loop
6. Self-diagnosis function can monitor • Dimensions:206mmX95mmX95mm
the inner fault.
7. Automatic compensation for factors
weakening received signals, such as
dust contamination, positional
excursion and ageing transmitter.
8. SMT processing technology Indication of Detector State:
9. Attractive and decent appearance
Commission: Green LED and Yellow LED
are lit or flash in a certain way.
Description
Normal monitoring state: Red LED
C-9105R Conventional Reflective Beam flashes periodically (with loop connected)
Detector is an addressable reflective infrared Fire: Red LED constantly illuminates, and
beam smoke detector that can be directly Yellow LED turns off. The fire signal has
connected to a fire alarm controller, by to be cleared by the controller
transmitting status information via bus Fault: Yellow LED constantly illuminates.
between the detector and controller. The
detector must be used together with a
reflector. The number of reflector(s) to be
used (one or four) depends on the distance
from the detector.

Conventional
Reflective Beam
Detector C-9105R

according to the wire diagram. The D1,D2
is for 24VDC power supply. The K11,k12 for
fire alarm output contact (passive). The
cable must be fire rated and the size
depends on the distance and application.
The minimum size gauge 1.0mm²
FIRE ALARM
OUTPUT
CONTACT
(TO FACP) TO POWER SUPPLY
24VDC
K22 K21K12 K11 D1 D2
Mounting the Detector

The detector can be mounted in 2 ways: the
installed onto standard two gang electrical Compatible with all GST Intelligent Fire
box, or directly by drilling the holes and Alarm Panels GST 200, GST 5000, GST
fixing with plugs. 9000 with interface module. Compatible
with all GST Conventional Fire Alarm
Control panel
/Kg Qty
per
Box
C-9105R Conventional 1.3 10
Reflector Beam
Detector

Conventional Gas
Detector C-9602LW Technical Specifications
• Operating Voltage: AC187V

AC253V
Monitoring State≤4W
Alarming State≤5W
• Output Capacity and Control Mode:
Active Contact: Applicable to 12V
one-way DC pulse solenoid valve,
driving ability: 1000μF capacitance
discharge.
• Passive Contact: Passive, normally
open contact, capacitance 220V/1A,
for controlling connected devices.
• Alarm Density:
Natural Gas: 5500ppm (11%LEL)
Coal Gas: 600ppm (1.5%LEL)
Features and Benefits Liquefied Petroleum Gas: 2800ppm
(14%LEL)
1. Available for LPG, Natural Gas and • Indicators: Power: Green; Alarm:
Coal gas. Red; Fault: Yellow
2. Self-diagnosis function can monitor • Warm-up state: Green LED flashes
the inner fault. at a frequency of 1Hz. After warm-
3. Built-in relay contacts for control Gas up, the green, red and yellow LEDs
Valve/Extract etc. will flash once in turn and the
4. Built-in Sounder buzzer will sound, showing the
5. Manual reset and control of relays detector enters monitoring state.
contact. • Monitoring State: Green LED lights
6. Wall mounting. Easy installation and normally.
connection. • Alarming State: Red LED flashes at
7. 220 VAC supply a frequency of 2Hz, and green LED
lights normally.
• Fault State: Green and yellow LED
Description lights normally.
• Buzzer: frequency of 2Hz during
C9602LW Gas Detector is suitable to detect alarming, and 0.3Hz in fault.
liquefied petroleum gas in such areas as • Self Test: Press “Self-Test” during
houses, hotels and apartments. This detector warm-up and monitoring state, the
is available for different application such as three LEDs will flashes in turn and
LPG, Natural Gas and Coal gas. (Please the buzzer sounds three times.
specify at the time of order). • Life of Sensor: 5 years
The detector adopts semiconductor gas- • Temperature: 0ºC~ +50 ºC
sensitive components enabling stable • Relative Humidity≤95%, no
operation and simple installation. It's condensation
powered by AC 220V. • Dimension: 176mm×80mm×45mm
• Degree of Protection of Enclosure:
IP30
ABS, ivory white
• Weight: 400g
• Mounting Hole Distance: 156mm

Conventional Gas
Detector C-9602LW

Mounting Gas Detector
The installation of gas detector should comply according to the wire diagram. K1, K2:
with all local codes and / or NFPA 72 National Normally open passive contact, which will
be closed when the detector alarms.
Code. Design to install onto standard conduit
electrical box (70mmx70mm). Recommended V (+), V (-): Connects with pipe solenoid.
location of the detector is show below. If the detector had alarmed for 3 to 7
seconds, there would be a delayed forward
12V pulse voltage between V(+) and V(-).
Ceiling
Smoke
Exhauster
Natural Gas and

Coal Gas Detector
¡Ý cm
Gas 1. 5m<L<4m
Stove
Liquefied Petroleum Power Supply

Gas Detector Within 30cm
Knock-off Holes
Floor
Compatible with all GST Conventional

Control Panels.
Part No Description Weight/Kg Pack Qty per Box
C-9602LW-NG Conventional Gas Detector Natural Gas .250 100
C-9602LW-LPG Conventional Gas Detector LPG Low Pressure .254 100
Gas
C-9602LW-CG Conventional Gas Detector Coal Gas .252 100

Conventional Optical
Smoke Detector R-6601 • Monitoring Area: When space
height is 6m-12m, the monitoring
area of a detector is 80m2 for
normal protection area; When
space height is less than 6m, it is
60m2.
Temperature: -10°C+50°C@95%
• Ingress Protection Rating: IP22
ABS, ivory white
• Weight: 119g
• Mounting Hole Distance:
45mm~75mm
Features and Benefits • Wiring: 2 pair polarized
1. 12 Vdc power conventional detector 5cm
2. Built-in N/O contact
3. Sensing chamber for exceptional dust Detector Installation
proof ability It is installed onto a standard one gang
4. Single LED electrical box with a mounting hole that
5. Low profile design have 6.5cm spacing. Point the detector in
6. Suitable for security system the base by the mark-line and secure the
Description clockwise until it reaches the next mark line.
With the technique of scattering, the CONCRETE PAD OR

HOLDING PAD
EMBEDDED BOX
detector's reliability, stability and consistency

are improved. The special chamber design
ensures the insert-defend, dirt-defend and MARK−LINE 2ND MARK−LINE
anti-light disturbance.
The detector is non-addressable and can start
operation by applying DC power. It has a
LED INDICATOR
pair of output contact, which is broken in ROTATE CLOCKWISE
normal and closes and remains closed after

alarming, and the indicator on the detector is Wiring and Connection
lit. It can be reset after power cut. The
detector adopts orientation base, with only The cable must be fire rated type and the
one mounting mode. size depends on the distance and
application. Minimum size gauge
1.0mm²(18 AWG).
• Operating Voltage:9.6VDC~14.4VDC Ordering Information:
Part Description Weight/ Pack Qty
Standby Current<1mA
No Kg per Box
Alarm Current<20mA R-6601 Conventional 0.123 120
• Alarm Reset: Instantaneous Cut-out Optical Detector,
(5s MAX, 2.5VDC MAX) 12-28VDC Power,
• Power-up Time≤10s N/O Relay Output
• Response Threshold: 0.10dB/m-
0.21dB/m MANUFACTURED IN ACCORDANCE WITH
• Output Control Mode: Passive

normally open, closes and self-locks
after alarming, and contact rated
capacitance (1A, 30VDC)
• Indicator: Red, not lit in normal Note: Specifications are subject to change without notice.
operation, and constantly lit when

alarming.

Conventional Heat
Detector R-6602
Temperature: -10°C+50°C@95%
• Ingress Protection Rating: IP22
ABS, ivory white
• Weight: 119g
• Mounting Hole Distance:
45mm~75mm
5cm
Features and Benefits Detector Installation

1. 12 Vdc power conventional detector electrical box with a mounting hole that
2. Built-in N/O contact have 6.5cm spacing. Point the detector in
3. Fixed Temperature the base by the mark-line and secure the
4. Single LED detector in that position by rotates it
5. Low profile design clockwise until it reaches the next mark line.
6. Suitable for security system
Description CONCRETE PAD OR EMBEDDED BOX

HOLDING PAD
R-6602 Conventional Heat Detector checks

ambient temperature with the sensitive
feature of thermo-sensitive elements. With a
built-in SCM, it’s fixed with highly reliable fire

judging program. The detector is non-
addressable and can start operation by LED INDICATOR
applying DC power. It has a pair of output ROTATE CLOCKWISE
contact, which is broken in normal and closes

and remains closed after alarming, and the Wiring and Connection
indicator on the detector is lit. It can be reset The cable must be fire rated type and the
after power cut. The detector adopts size depends on the distance and
orientation base, with only one mounting application. Minimum size gauge
mode. 1.0mm²(18 AWG).
Technical Specifications Ordering Information:

• Operating Voltage:9.6VDC~14.4VDC Part Description Weight/ Pack Qty
• Operating Current: No Kg per Box
Standby Current<1mA R-6602 Conventional Heat 0.123 120
Alarm Current<20mA Detector , 12-
• Alarm Reset: Instantaneous Cut-out 28VDC Power, N/O
(5s MAX, 2.5VDC MAX) Relay Output
• Power-up Time≤10s
• Response Threshold: 0.10dB/m-
0.21dB/m
• Output Control Mode: Passive
normally open, closes and self-locks
after alarming, and contact rated
capacitance (1A, 30VDC)
• Indicator: Red, not lit in normal
operation, and constantly lit when
alarming.

Smoke Alarm S-9102
• Power Supply: PP3 (H6F22) DC9V
battery
• Indicator: Red flashes in every 50
seconds in normal condition.
• Output Interface: Available for
optional use
• Network Output: Maximum 30
alarm in one system, available for
optional use.
• Photoelectric Output: 5mA /30VDC,
Optional
• Sound level : 80dB
Features and Benefits • Detection Area: 40m2
1. Self contain Optical Smoke detector • Temperature: -10 ~ +50
and alarm sounder • Relative Humidity: 95%
2. With test and reset button • Dimension: 140 x 54mm(D x H,
3. 9v operated with base)
4. Low battery indication • Material and Color: ABS white
5. Battery removable will inhabit cover • Weight: 235g
from closing ( as per UL standard) • Mounting Hole Distance:
6. Easy installation 50mm~108mm
7. LED indicator for 360º vision
8. Connection port to link up to 30
detectors in a single network Detector Installation and Wiring
9. Output to interface with other
security equipment The Smoke Alarm should be installed in
compliance with all local codes having a
jurisdiction in your area or NFPA 72
Description National Fire Alarm Code, NFPA 70 National
S-9102 Smoke Alarm is designed for Electrical Code, BS 5389 and EN54. For
domestic usage such as a house, villa and information about installation refers to
apartment, etc. Built with high-quality manual.
components and advanced technology, the
alarm has an excellently stable performance
and low power consumption. A 9V battery Ordering Information:
will operate up to one year. It can be easily
installed, no commission required. Part No Description Weight Pack
/Kg Qty
Utilize internal buzzer to provide a loud local per
Box
alarm. By using the output terminal, the
S-9102 Smoke Alarm 0.300 30
alarm can be linked to other alarms in a
common alarm network (up to 30 alarms) or
can be interfaced to other systems.

Conventional Manual
Call Point C-9201
• Approval: CE
Alarm Current 2mA
+50°C
Features and Benefits • Visual Indicator: LED, Red ( lit
1. Re-settable (non-breaking glass) steady when alarm, 3 sec interval
2. Additional volt free contact blinking at normal state)
3. Friendly installation and test • Material and colour: ABS, red
Description • Dimensions: 90x122x48.5mm
Designed for the purpose of raising an alarm
manually once verification of a fire or Mounting Base
emergency condition exists, by pressing the The location of manual call point should be
non breakable glass. Meets the standard installed in compliance with all local codes
requirement of EN 54 part 11, European and / or NFPA 72 National Fire Alarm Code,
Standard and approved by Loss Prevention NFPA 70 National Electrical Code. Surface
Certificate Board (LCPB). mount and it is installed onto a standard
The C-9201 constructed of high impact red
ABS with a modern pleasing appearance. The I−9201
WALL
terminating back box enables first fix
installation and termination leaving the fascia FIRE
ELECTRICAL
with integral electronics to be simply plugged BACK BOX
into base at the time of commissioning. Non

breakable glass that can be reset with the
MOUNTING
GST standard reset sucker. BASE
The C-9201 operated via a micro-switch that

when pressed a signal will be transmitted SURFACE MOUNT
and the volt free contact will be latched. one gang electrical box with a mounting
Contain integral LED indicator to denote hole that have 52mm~68mm spacing.
operational mode.
Compatible with all GST Conventional panels Part No Description Weigh Pack
t/Kg Qty
Wiring and Connection: per
Connect as per the marking on the base. Box
C-9201 Conventional 0.156 120
Manual Call Point
CONVENTIONAL
+
PANEL
1 2
K1 K2
−
OR
ZONE
MONITOR
TO NEXT DETECTOR
MODULE
I+ I− O− 0+
4 3 OR
AEOL
C−9202 MANUAL CALL POINT DETECTOR

Conventional Manual
Call Point C-9202
• Approval: LPCB, CE
Alarm Current 2mA
+50°C
• Dimensions: 97x100x45.5mm
1. Compatible with latest EN standards Mounting Base
2. Re-settable (non-breaking glass) The location of manual call point should be
3. Additional volt free contact installed in compliance with all local codes
4. Friendly installation and test and / or NFPA 72 National Fire Alarm Code,
NFPA 70 National Electrical Code. Surface
Description mount and it is installed onto a standard
Designed for the purpose of raising an alarm one gang electrical box with a mounting
manually once verification of a fire or hole that have 52mm~68mm spacing.
emergency condition exists, by pressing the
non breakable glass. Meets the standard C−9202 WALL
requirement of EN 54 part 11, European
Standard and approved by Loss Prevention FIRE
Certificate Board (LCPB). ALARM ACTION
ELECTRICAL
BACK BOX
The C-9202 constructed of high impact red PRESS HERE
ABS with a modern pleasing appearance. The

terminating back box enables first fix MOUNTING
BASE
installation and termination leaving the fascia
with integral electronics to be simply plugged Wiring and Connection:
into base at the time of commissioning. Non Connect as per the marking on the base.
breakable glass that can be reset with the
GST standard reset key.
The C-9202 operated via a micro-switch that CONVENTIONAL
+
PANEL
1 2
when pressed a signal will be transmitted

K1 K2
−
OR
ZONE
and the volt free contact will be latched. MONITOR

MODULE
I+ I− O− 0+
4 3
TO NEXT DETECTOR
OR
Contain integral LED indicator to denote

AEOL
operational mode.
C−9202 MANUAL CALL POINT DETECTOR
Selection of compatible Control Panels Ordering Information:

/Kg Qty per
and GST Intelligent Fire Alarm Panels using Box
Zone monitor module. C-9202 Conventional 0.156 120
Manual Call Point

Conventional Sounder
Beacon C-9401
polarized
24Vdc: Standby current 10mA
Action current 160mA
• Operating temp: -10°C to +50°C
• Flashing Frequency: 20x180 per
min.
• Alarm Volume (SPL): 90dB @ 1m
• Material and colour: ABS,ivorywhite,
red plexiglass
• Wiring:1 pair 24vdc supply
Dimensions: 144x90x57mm
Sounder Installation and wiring

The sounder beacon should be installed in
Electrical Code, BS5389 and EN54. It is
install onto a standard one gang electrical
spacing. The terminals DI(+)and D2(-) is
Features and Benefits for start-up power 24vdc. The cable must
be fire rated type and the size depends on
1. Combined flashing high intensity LED the wiring distance. Minimum
beacon and sounder recommended size gauge is 1.0mm².
2. Wall mount
3. Two part plug-in construction, no 24VDC
locking screw required

4. First fix base for easy and safe D1 D2
installation.
Mounting Hole Mounting Hole
Description
The conventional sounder beacon is suitable
for warehouse, security post, schools and
industrial area. The I-9401 is designed to S1 G
meet the requirement of EN54
The unit is utililised a red plexiglass cover Ordering Information:

and a number of strong signal red LED, long-
life and low consumption. Two part Part No Description Unit Pack
Weight Qty
construction with base mounted termination
/Kg per
allows easy installation and avoiding the Box
wiring and connection problem associated C-9401 Conventional 0.30 64
with traditional sounder. Sounder Beacon
Selection of compatible Control Panels MANUFACTURED IN ACCORDANCE WITH

sounder output and Intelligent Sounder
Driver Module

Base C-9402 Sounder Installation
The sounder base should be installed in
spacing.
CEILING ELECTRICAL WALL

BACK BOX
ELECTRICAL
C−9402 BACK BOX
DETECTOR
DETECTOR COMMON
Features and Benefits BASE
SOUNDER WITH
COVER
1. High sound level Wiring and Connection
2. Low power consumption Connect the wires to the required terminal
3. Can be used as a detector base according to the wiring diagram. The 5,6 is
4. Wall or ceiling mounting. Easy for 24VDC power supply, note the polarity 5
installation and connection. is positive and 6 is negative. The cable
must be fire rated type and the size
Description depends on the wiring distance. Minimum
In Fire and Security system the sounder is size gauge 1.0mm²(18 AWG).
the most effective device for alerting POWER SUPPLY/SOUNDER OUTPUT
personnel to evacuate the area. In the
POSITIVE WIRE NEGATIVE WIRE
buildings such as hotels where thick doors (5) (6)
and walls prevent external sound penetration,
the use of a combined detector base with
buit-in sounder present a cost effective 5 6
1 2
solution.
The GST C-9402 is a non-addressable
sounder base on which can mounted a
conventional detector to provide the dual
function of detection and alarm device or it
can be used as a single sounder. 4 3
28Vdc) polarized Selection of compatible Control Panels
• Operating Current: 15mA Compatible with all GST Conventional panel
• Operating temperature: -10°C to and GST Intelligent Fire Alarm Panels using
+50°C sounder output and Intelligent Sounder
• Relative humidity: 95% Driver Module
• Application: Indoor use Ordering Information:
• Material and colour: ABS, off-white Part No Description Weight Pack
• Wiring: 1 pair polarized /Kg Qty
• Dimensions: diameter 10cm; height : per
Box
3.5cm (w/o cover), 4.5cm (w/ cover)
C-9402 Conventional .120 100
Sounder Base

and Strobe C-9403 / C-9404
Description
The C-9403 is a conventional combined

wall mounting sounder and strobe while the
C-9404 is identical in appearance and
features to the C-9403 but without strobe
element. The audio efficiency and sound
distribution generate over 85 dB at 3
meters distance giving an excellent
audibility from the device location. Using
six highlights LED’s for high intensity visual
alarm to warn the people.
The GST sounder series are convenient

plug and turn installing method in shallow
or deep base. Easy cabling and connection.
C-9404
1. High sound level

2. Low power consumption
3. High intensity LED cluster
4. Easy installation and connection.
Specification
Part Number C-9403 C-9404

Approval LPCB,CE CE
Sound level output Evacuate sound: 85dB at 3 meters
Strobe 6 highlight LED’ No feature
Operating voltage Power Supply 24Vdc(16~28Vdc)
Supply current: standby 3mA / alarm Supply current: standby 3mA / alarm
Operating current
65mA 35mA
Addressing Mode Electronic programming with 1~242
Wiring 2 wire for power cable( non-polarized)

and Strobe C-9403 / C-9404
The sounder base should be installed in Selection of compatible Control Panels
compliance with all local codes or NFPA 72 Compatible with all GST Conventional panel
National Fire Alarm Code, NFPA 70 National and GST Intelligent panel using sounder
Electrical Code, BS5389 and EN54.Can be output and Intelligent Sounder Driver
mounted in a shallow base or Optional deep Module (I-9308)
base. It is installed onto a standard one gang
electrical box with a mounting hole that has
6.5cm spacing.
/Kg Qty
per
Box
WALL Conventional
C-9403 Sounder and 0.360 45
strobe
ELECTRICAL Conventional
BACK BOX C-9404 0.361 45
Sounder
Deep Base
C-94DB 0.070 100
(Optional)
MOUNTING
BASE

according to the wiring diagram. The D1, D2
is for 24VDC power supply, polarized. The
cable must be fire rated type and the size
depends on the wiring distance. Minimum
size gauge 1.0mm²(18 AWG)
Power Supply
24Vdc

6” Fire Alarm Bell
C-9410

spacing.
The red and black cable is for 24VDC power

supply, note the polarity Red is positive and
Black is negative. The cable must be fire
rated type and the size depends on the
wiring distance. Minimum size gauge is
1.00mm sq.

Fire alarm bell has a simple structure and red and GST Intelligent Fire Alarm Panels using
coated steel casing, with novel pattern and sounder output and Intelligent Sounder
easy installation. It is applicable to the fire Driver Module
alarm equipment of factory, workshop, hotel
as well as large and medium sized buildings. Ordering Information:
Under nominal voltage, the alarm sounds
clearly and continuously. Part No Description Weight Pack
/Kg Qty
per
Technical Specifications Box
C-9410 6” Fire Alarm 0.30 50
Bell
• Operating Current: 0.018A
+50°C
• Application: Outdoor/Indoor
• Material and colour: Stainless Steel;
RED
• Dimensions: Diameter 6 inches MANUFACTURED IN ACCORDANCE WITH

8” Fire Alarm Bell
Weatherproof C-9411

spacing.
The red and black cable is for 24VDC power

supply, note the polarity Red is positive and
Black is negative. The cable must be fire
rated type and the size depends on the
wiring distance. Minimum size gauge is
1.00mm sq.

Fire alarm bell has a simple structure and red and GST Intelligent Fire Alarm Panels using
coated steel casing, with novel pattern and sounder output and Intelligent Sounder
easy installation. It is applicable to the fire Driver Module
alarm equipment of factory, workshop, hotel
as well as large and medium sized buildings. Ordering Information:
Under nominal voltage, the alarm sounds
clearly and continuously. Part No Description Weight/ Pack
Kg Qty per
Box
C-9411 8” Fire Alarm 0.60 25
Bell – Weather
proof

• Operating Current: 0.060A
+50°C
• Application: Outdoor
• Material and colour: Stainless Steel;
RED
• Dimensions: Diameter 6 inches MANUFACTURED IN ACCORDANCE WITH

Conventional Fire
Alarm Panel GST101
• Operating Voltage
DC24V±15% or AC220V 50Hz
• Stand-by batteries are configured on
order. The battery capacity can be
calculated according to the formula in
Clause 5.6 of this manual. The
maximum capacity is 4Ah (lasting for 24
hours in monitoring state).
• Output voltage: DC20V DC28V
• Static current: 2.4mA (connected with
15 conventional detectors)
• Resistance when alarming fire: 150Ω
1.5kΩ (normally 470Ω)
• Terminal resistor: 4.7kΩ or using active
end of line unit(.AEOL)
• Sounder: Output voltage DC20V to
DC28V, output current 1A, terminal
Features and Benefits resistor 4.7kΩ.
• Fault: Passive contact output, capacity
1. Microprocessor controlled SMT 1A DC24V
Electronics • Dimension:210mm×297mm×90mm
2. Compliant with EN54 part 2&4, &
BS5839, Part 4, 1988
3. Both end of line resistors and active
end of line can be used. Selection of compatible devices.
4. Programmable sounder circuits and
Compatible with all GST conventional detectors
outputs
and sounders.
5. Fully monitored sounder circuits
6. Key control evacuate over-ride
7. Class change terminals for remote Ordering Information:
control Part No Description Weight Pack
8. Up to 25 fire detectors and infinite /Kg Qty per
manuals call points zone capacity Box
GST101 1 Zone 2.45 1
Description Conventional
Fire Alarm
GST101 Conventional Fire Panel is a kind of Control Panel
multi-wire fire panel using single-chip
microprocessor. It can detect 1 zone. Each
zone can at most be connected with 15
conventional detectors. It has 2 output
control points through which it can control
some indicators, such as sounder strobes and
sounders, etc. The panel is designed with
stand-by batteries (two sealed acid storage
batteries) and reserved space for installation;
It has functions of operation indication, fault
indication, alarm indication and cable MANUFACTURED IN ACCORDANCE WITH
checking for short circuit or broken circuit. It

can also identify the location of detecting
zone. Installation and operation of the panel
are very simple. All control functions are
realized through a key switch. Note: Specifications are subject to change without notice.

CONVETIONAL FIRE
ALARM PANELS
GST102/104
Description
The GST102/4 conventional fire control panels

provide two/four zones of fire detection. All
panels have been designed to offer high
standards of performance, reliability and
quantity and comply fully with BS5839, Part 4,
1988 and EN 54 parts 2 and 4. Each zone can
be connected with 15 conventional fire
detectors.
Microprocessor controlled SMT Electronics

The GST102/104 conventional control panels
are multi-wire fire alarm developed from SCM.
GST102 2Zone Fire Panel
Those with signal output interface board has a
passive normally open alarm output contacts
and fault output contact on each zone. They
have two external control output points to
control some devices such as sounder, sounder
strobe or bells.
Designed with internal standby battery

connection and housing. Multiple functions like
isolation and test, setting day/night mode ,
indication of normal state, fault state, alarm
state, short and open circuit alarm and
identifying the location of detector zone. All
control function are realized through a key
GST104 4Zone Fire Panel switch and programming function realized
through a key switch and a DIP switch.
Features and Benefits The GST conventional panels includes an

advanced range of facilities which make this the
1. Microprocessor controlled SMT Ideal panel for both standalone solutions, or
Electronics integrated to larger systems in applications
2. Compliant with EN54 part 2&4, & such as, shopping Canters and industrial
BS5839, Part 4, 1988 complexes.
3. Both end of line resistors and
active end of line can be used. Ordering Information:
4. Programmable sounder circuits
and outputs Part No Description Weight/ Pack Qty
5. Zone Isolate control Kg per Box
6. Fully monitored sounder circuits GST102 2Zone 5.494 1
7. Key control evacuate over-ride Conventional
Fire Panel
8. Class change terminals for
GST104 4Zone 5.500 1
remote control Conventional
9. Up to 15 fire detectors and Fire Panel
infinite manuals call points each
zone

Conventional Fire
Alarm Panels
GST102/104
Part Number GST 102 GST104
Operating voltage 220Vac ± 15% , 50hz
Standard BS5839, Part 4, 1988 and EN 54 parts 2 and 4
Approval CE, LPCB final stage
Number of Zone Two zone Four Zone
Zone Capacity 15 detectors (AOL);25 detectors (EOLR)
Standby Batteries 5AH , 24hours monitoring state
Output Voltage 20Vdc to 28 Vdc
Static Loading Current 2.5mA ( when connected with 15 conventional detector
Fire Alarming Resistance 150Ω-1.5KΩ ( normal 470Ω)
End Of Line resistor 4.7KΩ or AEOL ( Active End Of Line)
No. of Sounder Output 2
Sounder Output Current 1 Ampere (500mA per output)
Sounder Output Voltage 20Vdc to 28 Vdc
Aux.Power Output 20Vdc to 28 Vdc
Materials and colour Coated Metal / Grey
Conventional Fire Alarm System Typical Wiring Connection
Fig.1
Fig.2
Fig.3
Fig.1 Using End of Line resistor, in compliance with
EN/BS standard, when using EOL resistor, call points
should be wired before detectors, so that the removal of
any detector will not inhibit call point from operating.
Fig.2 Using Active End of Line, enables call points to be

installed in any location on zone as will not affected by
removal of detector (required base DZ-03D)
Fig.3 The same as fig.2 principle, using AEOL without

detector.

CONVETIONAL FIRE
ALARM PANELS
GST108/116
Description
The GST108/116 conventional fire control

panels provide eight/sixteen zones of fire
detection. All panels have been designed to
offer high standards of performance, reliability
and quantity and comply fully with BS5839,
Part 4, 1988 and EN 54 parts 2 and 4.
Microprocessor controlled SMT Electronics

The GST108/116 conventional control panels
are multi-wire fire alarm developed from SCM.
Those with signal output interface board has a
GST108 8Zone Fire Panel passive normally open alarm output contacts
and fault output contact on each zone. The two
kind panels have six control output points
through which it can control some devices such
as sounder, sounder strobe or bells.The rated
mazimum load is four sounder outputs and one
control output.
Designed with internal standby batteries

connection and housing. Multiple functions like
isolation and test, setting day/night mode ,
indication of normal state, fault state, alarm
state, short and open circuit alarm and
identifying the location of detector zone. The
reserved LED repeater interface can be used for
alarm detection. All control function are realized
GST116 16Zone Fire Panel
through a key switch and programming function
realized through a key switch and a DIP switch.
Features and Benefits The GST conventional panels includes an
advanced range of facilities which make this the
1. Microprocessor controlled SMT
Ideal panel for both standalone solutions, or
Electronics
integrated to larger systems in applications
2. Compliant with EN54 part 2&4, &
such as, shopping Canters and industrial
BS5839, Part 4, 1988
complexes.
3. Repeater Panel Interface
4. Both end of line resistors and Ordering Information:
active end of line can be used.
5. Programmable sounder circuits Part No Description Weight Pack Qty
outputs /Kg per Box
GST108 8Zone 4.930 1
6. Zone Isolate / Test control
Conventional
7. Fully monitored sounder circuits Fire Panel
8. Key control evacuate over-ride GST116 16Zone 5.584 1
9. Fire alarm output for remote Conventional
control Fire Panel
10. Class change terminals for MANUFACTURED IN ACCORDANCE WITH
remote control
11. Up to 15 fire detectors and
infinite manuals call points each
zone

Conventional Fire
Alarm Panels
GST108/116
Part Number GST 108 GST116
Operating voltage 220Vac ± 15% , 50hz
Standard BS5839, Part 4, 1988 and EN 54 parts 2 and 4
Approval CE, LPCB final stage
Standby Baterries 7AH , 24hours monitoring state
Output Voltage 20Vdc to 28 Vdc
Static Loading Current 2.4mA ( when connected with 15 conventional detectors
Fire Alarming Resistance 150Ω-1.5KΩ ( nominal 470Ω)
End Of Line 4.7KΩ or AEOL ( Active End Of Line)
Sounder Output 4:Output voltage: 20Vdc ~28Vdc ; Output current: 1 A
Fire Alarm Output Output voltage: 20Vdc ~28Vdc ; Output current: 0.5 A
Fault Output Capacity Passive contact output :24vdc / 1 A
Aux.Power Output 20Vdc to 28 Vdc, 0.5A
Repeater Panel Outpt 10mA
Zone Capacity 8 zone 16 Zone
Materials and colour Coated metal/Grey
Conventional Fire Alarm System Typical Wiring Connection
Fig.1
Fig.2
Fig.3
Fig.1 Using End of Line resistor, in compliance with

EN/BS standard, when using EOL resistor, call points
should be wired before detectors, so that the removal of
any detector will not inhibit call point from operating.
Fig.2 Using Active End of Line, enables call points to be

installed in any location on zone as will not affected by
removal of detector (required base DZ-03D)
Fig.3 The same as fig.2 principle, using AEOL without

detector.

16 Zones Conventional
Repeater Panel GST-RP16 Technical Specifications
• Operating voltage: 18Vdc to 28Vdc
polarized
• Standby: 12mA; Alarm:60mA
• Operating temperature: 0°C to
+40°C
• Display Capacity: 16 Zone Fire
Signal, 2 Fault signal
Features and Benefits • Application: Indoor use
• Material and colour:
1. Compatible with GST 102,104.108 • Wiring: Multi-wire (16 for zone
and GST 116 signal, 2 for fault signals) and two
2. Powered from Fire Panel directly for power supply cable.
3. Zone Fire and general Fault Indication • Dimensions: 280mm x 110mm x
4. Description 46mm
Description Selection of compatible Control Panels

GST-RP-16 Conventional Repeater Panels, Compatible with GST108/116 Conventional
the supporting products of conventional fire panel.
panel, is a type of fire display unit used in Ordering Information:
building or fire control center. When the
Part No Description Weight/ Pack Qty
conventional fire panels received fire signal,
Kg per Box
it will alarm and send the signals to the GST-
GST-RP16 16 Zone 0.900 120
RP16 , then the GSTRP-16 will indicate the Conventional
alarm zone and sound to notice the people Repeater
there accordingly. Panel
Typical Wiring Diagram
G S T−R P 16 C O N V E N TIO N A L R E P E A TE R P A N E L
24V G N D F IR E1 FIR E 2 FIR E 3 F IR E4 FIR E 5 F IR E 6 F IR E7 F IR E8 FA U 1 F IR E9 F IR E10 FIR E 11 FIR E 12 F IR E13 FIR E 14 FIR E 15 F IR E16 FA U 2
AU X FAU LT O U TP U T
PW COM COM COM COM SU P PLY
E AR TH O N 0V D AY FIR E IS O FLT Z8 Z7 Z6 Z5 Z4 Z3 Z2 Z1 − + NO COM NC
L N
G S T108 8ZO N E C O N V E N TIO N A L P A N EL

Fire Telephone Mobile
Handset P-9911(M)
• Frequency Range: 300-3400Hz
• Ring Sound level: 70 db(A)
• Voice Distortion: less than 10%
• Jack Diameter: 6mm
• Operating Current: 17~31mA
• Operating temperature: 0C to
+40°C
Selection of compatible panel

9 GST-FT24 24Zone Conventional Fire
Panel Centre
9 GST-FT8W 8Zone Conventional Fire
Panel Centre
Features and Benefits /Kg Qty
per
1. Easy to insert mobile handset Box
P-9911(M) Fire Telephone .250 10
2. Compatible with GST Fire Telephone
Mobile
Jack Handset
Description Note: Specifications are subject to change without notice.
P-9911(M) is a mobile type emergency

telephone handset, which can be taken by
the security, fireman or others on duty. The
person can go to the nearest jack sockets,
plug & talk to the central GST-FT24 panel
located in the command center.

Fire Telephone Jack
Socket P-9911(J)
• Jack Diameter: 6mm
+50°C
• Material and colour: ABS,white, red
• Dimensions: 850mm x 850mm x
120mm

Panel Centre
Panel Centre
1. Easy to insert mobile handset

2. Wall mounted. Easy installation and Ordering Information:
connection. Part No Description Weight Pack
/Kg Qty
Description per
Box
P-9911(J) is a telephone jack socket,
P-9911(J) Fire Telephone
normally located at various places. Common Jack socket
installation positioning is in the landing levels
of all core stairwells and escape routes, Note: Specifications are subject to change without notice.
although the exact positioning is the
responsibility of the project designer. The
person on site with a mobile handset may
12
just plug & talk to the control center. The
unit should be mounted in a suitable and dry
location at about 1.5m from finished floor
level.
85

The jack socket can be installed with
standard electronic back box, which the
mounting hole distance is 60mm. Connect
the cable to the terminals. No need 60
addressing. Connections refer to FT panel 85
manual.

Fire Telephone
Handset P-9911(F)
• Frequency Range: 300 to 3400hz
• Ring sound: >70dBA
+40°C
• Material and colour: ABS,white, red
• Dimensions: 234 x 146mm x 60mm

Panel Centre
Panel Centre

1. Fixed extension of fire telephone Part No Description Weight Pack
System /Kg Qty
2. Box for total protection. per
3. Wall Mounted and easy installation Box
P-9911(F) Fire Telephone
Handset
Description Note: Specifications are subject to change without notice.
P-9911(F) is a telephone jack socket,

normally located at various places. Common
installation positioning is in the landing levels
of all core stairwells and escape routes,
although the exact positioning is the
responsibility of the project designer. The
person on site with a mobile handset may
just plug & talk to the control center. The
unit should be mounted in a suitable and dry
location at about 1.5m from finished floor
level.
The fixed can be installed with standard

electronic back box, which the mounting hole
distance is 60mm. Connect the cable to the
terminals. No need addressing. Connections
refer to FT panel manual.

Conventional Fire
Telephone PanelGST-FT24
Operation
The GST FT24 provides two methods of
calling, i.e. from the hand set to the
relevant remote zone or from the remote
telephone point to the control centre.
Call Handset.From the control centre, press

the relevant zone connect button, this will
make the relevant handset ringing. (Or sets
ring depending on the quantity of handsets
connected to that specific zone). When that
zone is activated the field handsets will ring,
to establish audio communication simply
Features and Benefits pick up the handset, or for the hands-free
version, just press the talk button),
1. 24 Zone conventional fire telephone communication is achieved. Press button
center. again in the control centre to cancel the call.
2. 2-way voice communication
3. Operator can select single or group Call Control Center. Make the zone active
call (Fixed handset - pick the phone. Speaker
4. Operator can ring outstations and handset - press the button. Socket - insert
fixed handsets the mobile handset), will make the control
5. Up to 10 communication points can panel alarm with LED zone indication. From
be connected to each zone the control centre, press the corresponding
button to achieve communication.
Description
The GST Fireman’s Telephone (GST-FT24) Group Call. The fire telephone panel can
system is a dedicated audio communication talk to more than one handset. Simply by
system linking directly to the fire control Pressing all the desired zone buttons on the
center, providing 2-way speech between the control panel, This will allow group
fire team and the Central Command communication. To add or cancel more
Controller. Usually the GST FT system is users simple select or deselect the relevant
installed in high-risk buildings where radio zone.
communication would be limited due to the Audio Record. Whenever you start audio
extensive concrete structure. The GST FT-24 communication, the electronic recorder will
is a 24-zone system radially wired (2 core) automatically record the conversation.
with up to 10 communication points on each There is a total memory capacity of 99
zone. The system includes single and multi records (indicated by the digital-LED). The
channel (group) communication, Audio records can be played back, with the last
recording of conversations, Monitored cable communication first. The operator can skip
protection. to the desired message for play back by
simply using <review> and <Forward> to
Technical Specifications step through to the desired recording.
• System Capacity: 24 communication
Audio Output. A line level audio out put is
zone
provided should the system require to be
• Frequency Range:300-3400Khz
linked to a public address or Voice alarm
• Cross Talk: <-60dB
system.
• Audio Feedback:<5dB
• Zone Accepted Resistance: <1KΩ
• Operating Current: 500mA
• Operating temperature: 0°C -40°C
• Relative humidity: 45% to 95%
• Dimensions: 132.5x482.6x225mm

Conventional Fire
Telephone PanelGST-FT24
System Configuration Selection of GST-FT24 compatible fire
telephone
The GST FT24 is mounted in a standard 19” P-9911(S) Speaker Fire Telephone
rack enclosure. The system is wired in radial Station
conventional zones. In each zone it is P-9911(F) Fixed Fire Telephone
possible to mix fixed handsets, speaker Handset
handset and Jack sockets. The panel is P-9911(J) Fire Telephone Jack
standard 3U console mount type, can be Socket
installed together with the fire alarm control P-9911(M) Fire Telephone Mobile
panel GST5000 or GST9000 (both rack and Handset
console type). Connect 24VDC to the
terminals on the rear of the panel. Connect
the zones to the panel with minimum 2 core Ordering Information:
1.0mm2 cable.
/Kg Qty
Regularly Test. As with all Life safety per
equipment regular testing should be carried Box
out, we would recommend that all zones are GST-FT24 Conventional 6 1
tested at least every 3 months or as Fire Telephone
indicated by your local fire authority Panel
requirements. Note: Specifications are subject to change without notice.

CyberNet Touch Screen
Controller GST8101
1. 10.4” TFT touch screen

2. Powerful and user friendly
operation GST8101S
3. Supports Windows 98/2000/XP
4. Full system monitoring, indicating
operation of each unit
5. Capable of controlling 99 zones
6. Up to 3 Touch screen controllers
per system.
Description
The GST8101 provides a fully loaded user friendly Touch screen controlled PC
front end, providing a flexible management window to the entire system.
Enabling both Engineers to configure all aspects of the system, while system
managers can configure and control the day to day operation of the system. This
includes back ground music source selection, volume control routing to any
individual area, zone or group of zones,
Up to three Cybernet touch screen controllers can be utilized on any one system.
• Power Supply: 220Vac±10%/50Hz ; 24Vdc±10%

• Power consumption: 300 Watts
• Baud rate: 9600bps
• Communication protocol: RS 232
• Communication terminal: DB9
• Rack space: 10U
• Case Materials: Black aluminum steel
• Dimension: 484 X 265 X 430mm
• Net weight: 8.5 kg

Master Controller
GST8102

1. Master controller of complete
system up to 99 zones.
2. Automated intelligent
programmable processor control.
3. Can stores 500 system events
4. Program downloaded from
GST8101 or computer with
GST8101Software
5. Large LCD screen display
6. User friendly menu operation
7. Allows manual control of amplifiers
8. Communicating monitoring control with entire system
9. Self-diagnostics
10. Built in battery box
11. 220 AC / 24V DC operation
Description
The GST8102 is the heart of the system providing direct communication and
programming of all VA modules. The Master Controller provides complete reporting and
fault diagnostics.
Power Supply AC220V±10%/50/60 HZ
Power Consumption 30Watts
Keypad 1 Direction Key;9 Function Keys;2 Shortcut Keys
Display 192X64 LCD, English Menu;2 LED Fault Indicators
Communication Protocol RS-232, DB9, IN;RS422, RJ45, OUT
Baud Rate 4800bps
Case Material Black Stainless Steel
Back up Supply Battery 17AH/24VDC with battery box
Net Weight 12.5kg (without battery)

Audio Processor
GST8103

1. Simultaneous broadcast of 6 audio
channels. Providing Selection and
controlled from any number of
sources.
2. Support 8 emergency
microphones within 500 metres.
3. Individual volume display for each
channel
4. Forced switch terminal operations by program in case of emergency
5. Self-diagnostics
Description
The audio process controls and manages six audio channels, three channels dedicated to
voice alert and evacuate message, with three more channels dedicated to background
music sources and manual paging.
Keypad 1 Direction Key;9 Function Keys;2 Shortcut Keys
Display LCD, level Indicator
RS422, RJ45, In;DB15 to microphone; Screw types to
Communication Protocol
amplifiers
Channel Insulation ›40dB
Volume Adjustment -∞ to 0 dB
S/N Ratio 95dB
Baud Rate 4800bps
Audio Input 6 channels, RCA connector ; 10kΩ/0.775V
Audio Output 6 channels, screw fixing
Rack Space & Dimension 3U: 555 X 555 X 235mm

Emergency Interface
GST8104
1. Emergency zonal signal interface

provides a programmable
interface with GST intelligent Fire
detection systems
2. Micro-processor controlled
3. 30 zones input, expandable to 99
zones
4. Ideal for fire alarm control of phased evacuation.
5. Self-diagnostic
Description
The Emergency Interface provides a simple and reliable interface to any fire
alarm system. The GST8101S can perform the most complicated cause and
effect with care.
Power Supply: 220Vac±10%/50Hz ; 24Vdc±10%

Power consumption: 15 Watts
Communication protocol: RS 422
Communication terminal: RJ45
No of inputs: 30 inputs
Input Mode: N/O dry contact
Rack Space 2U
Colour and Materials Black, Alloy aluminum
Dimension: 484 X 350 X 88mm
Net weight: 4.3 kg

Emergency Message
Generator
GST8105

1. Micro-processor controlled message store
for Alert, Evacuate, Clear and Test
2. Can broadcast 2 types of message
simultaneously
3. Can broadcast Evacuate and Alert even
master controller is malfunction.
4. Massages can be re-recorded locally.
5. Up to 200 seconds of digital recording
6. Self-diagnostics
Description
The Emergency Message Generator stores up to four non volatile messages of up to 50b
seconds in length. The message can be accessed independently and broadcast to any
combination of zones.
Display 6 LED, level Indicator
Communication Protocol RS422, RJ45, IN/OUT
S/N Ratio 95dB
Baud Rate 4800bps
Frequency Range 30-20Khz
Record Input Terminals 6.5mm jack;Mic: 600Ω/10mV; Line: 10kΩ/0.775V
Audio Output Terminals 2 channels, 6.5mm jack, 1kΩ/0-1.5V
Rack Space & Dimension 3U: 555 X 555 X 235mm

Emergency Microphone
GST8106

1. Desk top configuration.
2. Fist Microphone
3. Highest priority access to system
4. Directly connecting to audio processor
GST8103 ,maximum 500 meters
5. Simple operation capable of
broadcasting to
9 SINGLE AREA CALL (node)
9 ZONAL CALL
9 All CALL
9 CLEAR and TEST
6. Simple action of broadcasting All Evacuate, All Clear, Reset and Zonal Test
7. With Chime, microphone, auxiliary volume control
8. Self-diagnostics
9. LED status and zonal indication
10. 24Vdc operation
Description
The Emergency Microphones provides complete and precise emergency management of
the entire system. The security or fire officer can quickly and accurately relay live voice
announcement to any single or multi zones or all call. Manual evacuation, test, all clear
can be initiated from this station.
Power Supply 24Vdc
Keypad 99 Zonal keys, 6 function keys
Display LED indicator in each key
Communication Protocol RS422, DB9 In/Out
Chime type 1
Microphone type Fist microphone/600Ω/10mV
Sensitivity -62dB
S/N Ratio 95dB
Baud Rate 4800bps
Numbers in series 8 microphones within 500 meters
Dimension 245 X 65 X 315mm
Case Material Silver Alloy-Aluminum
Net Weight 3.5Kg

CD Player
GST8180
1. Single CD player
2. Micro-processor
controlled
3. Local control
4. Programmed flexibly
controlled by TW-010
5. Self-diagnostics
Description
The CD Players provides high quality sampling of CD’s in both standard format
and MP3 format. The CD is fully programmable and ultimately reliable
Part Number: GST8180

Power Supply: 220Vac±10%
Output voltage: 0.75V
Frequency range: 50-15000Hz
Rack Space 2U
Net weight: 6 kg

Digital Tuner
GST8181
1. Micro-processor controlled
2. Backlight LCD display
3. Local /remote channel selection
4. FM/AM 99 individuals presetting
5. Accurate frequency control
6. Self -diagnostics
Description
The Digital Tuner is ideal for background music , the tuner provides up to 99
pre-programmed radio stations for excellent music selection
Part Number: GST8181

Power Supply: 220Vac±10%
Output voltage: 0.75V
Frequency range: 50-15000Hz
Rack Space 2U
Net weight: 6 kg

Node Terminal
Addressable Amplifier
GST8330/60

1. Addressable amplifier
2. 6-channels input
3. 100V/ output
4. Local 3 BGM channel input
5. Maximum volume override in case of emergency
6. Speaker loop monitoring
7. With 2 cooling fan
8. Built in battery box
9. Self diagnostics
10. With security lock and 2 LED’s indicator
Description
The Node Terminals Addressable Amplifier range provides truly distributed voice evacuate plus
background music system. The amplifier is mounted in self contained enclosures combined with
power supply and battery space. Distribution of amplifiers provides excellent wiring saving
capabilities and enhanced local control is achieved via three direct audio inputs and volume control
with master override.
Model GST8330 GST8360

Back-up Battery 17 AH / 24 Vdc
Power Consumption 60Watts 120Watts
Power Output 30Watts 60Watts
Keypad 99 Zonal keys, 6 function keys
Display 2 LED indicator for power and fault
Communication Protocol RS422, Screw fixing, In/out
Channel Control Input 1, Screw fixing
S/N Ratio 95dB
Baud Rate 4800bps
Dimension 415 X 343 X 135mm
Case Material Dark-grey coated steel sheet
Net Weight 18.5kg excluding battery

Node Terminal
Addressable Amplifier
(Rack Mount Type)
GST83R Series
1. Addressable amplifier
2. 6-channels input
3. 100V/70V output
4. Local 3 BGM channel selection and
32 level volume control
5. Maximum volume override in case of emergency
6. DC speaker line monitoring
7. Self diagnostics
Description
The Node Terminals Addressable Amplifier range provides intelligent addressable
distributed voice evacuate plus background music system. The amplifiers are
rack mounted with integral power supply and battery space. Option intelligent
soft start power supply to avoid inrush current use TW 090 is achieved via three
local audio inputs and volume control with master override
Part Number GST8330R GST83120R GST3240R GST8350R
Power Supply AC220V±10%/50HZDC24V±10%

Power Consumption 100W 200W 400W 600W
Power Output 60W 120W 240W 350W
Output Mode 100V/70V
Frequency Range 20-15000Hz ±3dB
Channel Isolation >40dB

SNR >70dB
Distortion <0.1%
Comm Protocol RS-422
Comm terminal RJ45
Rack Space 3U
Case Material Black Alloy-Aluminum
Dimension 484×450×132mm
Net Weight 11kg 13kg 18kg 21.5kg


Ceiling Speaker
GST8401
• Full range ceiling

speaker
• Ideal for emergency and
music broadcasting.
• Simple installation from
underside of ceiling tile
• No visible fixing screw
• High temperature
ceramic termination
block
Model GST8401
Operation Voltage 70/100V
Rated Power 6W
Max. Power 9W
Sound Level (@6W/1W,
94dB/88dB(SPL)
1kHz,1M)
Frequency Range 80Hz to 18kHz
Transformer Tapping 1.5W, 3W, 6W
Opening Angle 150°
UL 1411 / IEC 268-5 / UL94 V0 /
Compatible Standard
EN60065
Case Material Fire Resistance ABS
Grid Material Steel
Color White (RAL 9010)
Weight 650g
Speaker Size 152.4mm
Total Dimension 198X91.44 mm
Operation Temperature -25°C to +55°C
M
NUFACTURED IN ACCORDANCE WITH

Wall Mount Speaker
GST8411
• Full range wall mount speaker

• Ideal for emergency and music
broadcasting.
• Simple installation from underside of
ceiling tile
• Ideal for corridors, stairs, lift lobby,
plants rooms and hotel back house
areas.
Model GST8411
Operation Voltage 100V
Rated Power 10W
Max. Power 15W
89dB±3dB(SPL)
1kHz,1M)
Case Material High quality plastic PVC
Grid Material Steel
Colour White (RAL 9010)
Weight 2.2 Kg
Total Dimension 215x170x150 mm
Operation Temperature -25°C to +50°C

Pendant Speaker
GST8421
• High quality sound pendant

speaker
• Luxurious silver-gray plastic
cabinet
• With strong metal fixing bracket
• Ideal for use in a modern
building interior
• Ideal for indoor hall,
supermarket, stores and high
ceiling environments
Model GST8421
Speaker Unit 5” woofer paper
Operation Voltage 70/100V
Rated Power 9W
Max. Power 9W
Sound Level (1W,,1M) 95dB±3 (SPL)
Transformer Tapping 3W, 6W, 9W
Terminals 4-core
Case Material Plastic
Grid Material Plastic
Color Silver-gray
Weight 1.45Kg
Total Dimension Ǿ172x285mm

Sound Projector
Speaker GST8431
• High quality double sound

projector for voice evacuate
and PA system
• Waterproof light-aluminum
alloy cabinet and bracket
• With strong metal fixing
bracket for wall or ceiling
mount
• Ideal for corridors, car parks,
stair lobbies, plaza, swimming
pool, exhibition room, factories
and plant rooms
Model GST8431
Operation Voltage 100V
Rated Power 10W
Max. Power 15W
102dB±3 (SPL)
1kHz,1M)
Frequency Range 250Hz to 8 KHz
Case Material Aluminum alloy
Grid Material Steel
Color White
Weight 2.1Kg
Total Dimension 102
NUFACTURED IN ACCORDANCE WITH

Horn Speaker
GST8441
• High efficiency horn speaker

• Wide frequency response and
high SPL
• Waterproof white plastic
suitable for all types of
weather
• Durable construction ensures
long term reliable operation
• Ideal for car parks,
warehouses, plant rooms and
noisy production area.

Operation Voltage 70/100V 70/100V
Rated Power 15W,25W 10W
Max. Power 25W 10W
Sound Level (@1M) 113dB±3 (SPL) 103dB±3 (SPL)
Frequency Range 250Hz to 8kHz 250Hz to 8kHz
Impedance 280Ω, 410Ω 680Ω, 1.1KΩ
Case Material plastic plastic
Colour White White
Weight 3.2Kg 7Kg
Dimension 285x285x210 mm 285x285x210 mm

9” Equipment Rack
GST86033/86039
• Ideal for Public address and

Voice alarm System
• U’s Available in 39,33 and 27
• Built-in 2 fan tray
• Removable side panels
• Easy to construct

Dimension:mm 1820x600x650 1555x600x650
Weight: Kg 60 50
Material Aluminum
Equipment patter 19” EAI hole patter
U’s available 39U 33U
Side panels Removable
Front panel Lockable glass door
Back panel Lockable
Air Cooling 2 Fan Tray
Cable running Cable manageable

Explosion Proof and
Intrinsically Safe Product

Digital Flame Proof
Ultraviolet Flame Detector
DI-9104EXD
Operating Voltage Loop voltage: 24V

Operating Current Standby current ≤ 2mA
Action current ≤ 2.5mA
Power-up Time ≤5s
Indicator Red. It flashes when
polling, and illuminates
steadily in alarm.
Wiring Two wire connection with
FACP, polarity-
Features: insensitive.
Programming Mode Electronic programming.
Occupying one loop
• Intelligent signal-processing and
address.
communication with integrated
Address Range 1-242
microprocessor.
Spectrum 185nm-260nm
• Intelligent algorithm ensures quick Response Range
response with reduced false alarm. Detection Angle
• Three sensitivity levels.
• High sensitivity, reliable performance.
• Dust /corrosion/humidity resistante
• Secure and speedy communication
• Self diagnosis and history log
• Effective range 12 to 25 metres
Detection 25m for Level I, 17m for
• Electronic addressing
Distance Level II and 12m for
• Loop Powered Level III.
• Twin LED for 360º vision Ingress Protection IP66
• Mounting bracket support wall or Ambient -20°C to +40°C
ceiling mount. Temperature
Relative Humidity ≤95%RH, non-
condensing
Description: Dimensions 147mm×103mm×92mm
Material and Color ZL102 Aluminum alloy,
DI-9104Exd is a light-sensitive detector that silvery grey.
detects fire by picking up the ultraviolet light Weight 1.5kg
from flaming material. It’s designed for areas Installation Hole 110mm×72mm
where an open fire is liable to occur with Spacing
large amount of radiation, with no Explosion-proof Ex d0CT6
smoldering stage, or where quick response to Mark
Explosion-proof CE061027
a fire is required. This detector can be
certificate
applicable to zone 1 and 2 of explosive areas Standards to EN 54-10
comply with in GB 3836.1 GB 3836.2
Secure and speedy communication through design IEC 60079-0 IEC
the on board processor enables the detector 60079-1
to make its own decision, resulting in greater
automation. The sensor and the panels
utilized fuzzy logic providing an almost
limitless cause and effect scenarios.


Digital Flame Proof
Ultraviolet Flame Detector
DI-9104EXD
Connection and Wiring Ordering Information:

Screened 2-core cable with cross section
1mm2 or above, and outer diameter φ8 Part No Description Weight/ Pack
Kg Qty per
mm is required for field wiring., ZI and
Box
Z2 for the loop.
DI-9104EXD Digital Flame 1.5 120
Proof Ultraviolet
Flame Detector
Expansion Bolt 3
Safety Area Hazardous Area
M6×60
Screws M3×16 2
FACP
Z2
Z1 MANUFACTURED IN ACCORDANCE WITH
DI-9104Exd Detector
Installation
Note: The detector shall be installed in
compliance with relative installation codes.
Make sure the housing is in good condition.
M6×60
M3 ×

Innovation Conventional
Flame Proof Ultraviolet
Flame Detector DC-9104EXD
Operating Voltage Loop voltage: 24V

Operating Current Standby current ≤ 2mA
Action current ≤ 2.5mA
Power-up Time ≤5s
Indicator Red. It flashes when
polling, and illuminates
steadily in alarm.
Wiring Two wire connection with
FACP, polarise
Spectrum 185nm-260nm
Response Range
Detection Angle
Features:
Detection 17m
• Communication with integrated Distance
microprocessor. Ingress Protection IP66
Ambient -20°C to +40°C
• High sensitivity, reliable performance.
Temperature
• Dust /corrosion/humidity resistante Relative Humidity ≤95%RH, non-
• Secure and speedy communication condensing
• Effective range 12 to 25 metres Dimensions 147mm×103mm×92mm
• Twin LED for 360º vision Material and Color ZL102 Aluminum alloy,
• Mounting bracket support wall or silvery grey.
ceiling mount. Weight 1.5kg
Installation Hole 110mm×72mm
Spacing
Description: Explosion-proof Ex d0CT6
Mark
DC-9104Exd is a light-sensitive detector that Explosion-proof CE061027
detects fire by picking up the ultraviolet light certificate
Standards to EN 54-10
from flaming material. It’s designed for areas
comply with in GB 3836.1 GB 3836.2
where an open fire is liable to occur with design IEC 60079-0 IEC
large amount of radiation, with no 60079-1
smoldering stage, or where quick response to
a fire is required. This detector can be
applicable to zone 1 and 2 of explosive areas

Innovation Conventional
Flame Proof Ultraviolet
Flame Detector DC-9104EX
Connection and Wiring Ordering Information:

Screened 2-core cable with cross section
Part No Description Weight/ Pack
1mm2 or above, and outer diameter φ8 Kg Qty per
mm is required for field wiring., ZI and Box
Z2 for the loop. DC-9104EXD Innovation 1.5 120
Conventional
Flame Proof
Ultraviolet
Safety Area Hazardous Area Flame Detector
Expansion Bolt 3
M6×60
FACP
Z2
Screws M3×16 2
Z1

DI-9104Exd Detector
Installation
Note: The detector shall be installed in Note: Specifications are subject to change without notice.
compliance with relative installation codes.
Make sure the housing is in good condition.
M6×60
M3 ×

Explosion Interface
I-9332
Bus Voltage: 24V Range Allowed: 16V-
28V
Power Voltage: 24VDC Range
Allowed: 20VDC 28VDC
Standby Current≤0.5mA
Alarm Current≤5mA
programming within 1-242, occupying
one loop address.
• Wiring: Non-polarized two-bus with the
controller; non-polarized two-wire with
DC24V power cable; polarized two-wire
with explosion-proof devices.
Features and Benefits • Operating Environment:
Temperature: -10°C+5°C
1. Interface for Intrinsically safe detectors
and manual call point Relative Humidity≤95%, no
2. Electronically addressed condensation
3. Microprocessor supervises running status • Dimension: 200mm×162mm×85mm
and gives diagnosis message. • Safety Barrier Parameters: U0=28V,
4. With a built-in safety barrier, the I0=93mA, L0=4.3mH, C0=0.04μF
interface can directly match with • Weight: 1.5kg
intrinsically safe devices. • Mounting Hole Spacing: 192mm
212mm
• Material and Color of Enclosure: Q235A,
Description grayish white
• Ingress Protection level: IP 33
I-9332 Interface can match with explosion-
proof devices (explosion-proof smoke Selection of compatible Control Panels
detector, heat detector, combination
smoke/heat detector or manual call point) to Compatible with all GST Intelligent Fire
form an intrinsically safe system. When fire Alarm Panels.
occurs, the interface sends alarm signal to
fire alarm controller through loop and the Ordering Information:
controller will give alarm signal and display
the alarm address of the interface. When the Part No Description Weight/ Pack
interface itself is in fault, the controller will Kg Qty per
Box
give fault signal and display the fault address
of the interface.
Interface for
Detectors & MCP
including Zener
Electronic addressing can be done through Safety Barrier-Ex

Explosion Interface
I-9333
Bus Voltage: 24V
Range Allowed: 16V 28V
Power Voltage: 24VDC
Range Allowed: 20VDC -
28VDC
Standby Current≤0.5mA
Alarm Current≤500mA
programming within 1-242,
occupying one loop address.
• Wiring: Non-polarized two-bus with
the controller; non-polarized two-
wire with DC24V power cable;
polarized two-wire with explosion-
proof devices.
• Operating Temp: -10ºC to 50ºC
Features and Benefits • Relative Humidity≤95%, no
condensation
1. Interface for Intrinsically safe sounder • Dimension:
and sounder strobe 200mm×162mm×85mm
2. Electronically addressed • Weight: 1.5kg
3. Microprocessor supervises running status • Mounting Hole Spacing: 192mm
and gives diagnosis message. 212mm
4. With a built-in safety barrier, the • Material and Color of Enclosure:
interface can directly match with Q235A, grayish white
intrinsically safe devices. • Ingress Protection Level: IP33
Description Selection of compatible Control Panels
I-8333 Interface can match with explosion- Compatible with all GST Intelligent Fire
proof sounder to form an intrinsically safe Alarm Panels.
system. When fire occurs, the interface
received alarm signal to fire alarm controller Ordering Information:
through loop and the controller will give
alarm signal activate the alarm. When the Part No Description Weight/ Pack
interface itself is in fault, the controller will Kg Qty per
Box
give fault signal and display the fault address
of the interface. Interface for
Sounder
Electronic addressing can be done through including Zener
Handheld Programming tool (P-9910), Safety Barrier-Ex

Intrinsically Safe
Combined Detector
C-9101Ex
• Operating Voltage: DC24V, range

allowed: DC12V~DC24V
Standby Current≤60μA
Alarming Current≤30mA
• Wiring: 1 pair
• Alarm Confirming LED: Red
• Heat Sensitivity: Class I
• Dimension: Diameter: 100mm, Height:
42mm (excluding the base)
• Safety Barrier Parameters: Uo=28VDC,
Io=93mA
Features and Benefits Temperature: -10ºC+40 ºC
1. Multifunctional and highly reliable Relative Humidity:≤95%, no
detector condensation
2. Sensing chamber for exceptional dust • Monitoring Area: When space height is
proof ability 6m to 12m, the monitoring area of a
3. Twin LED for 360º vision detector is 80m2 for normal protection
4. Low profile design area; When space height is less than
5. Initiated by fire alarm point using 6m, it is 60 m2.
I-9332Ex Interface
• Enclosure Protection Level: IP22
• Material and Color of Enclosure: ABS,
Description ivory white
C-9101 Explosion-proof Combination
Call Point Installation
Heat/Photoelectric Smoke Detector is a kind
of combination detector consisting of smoke
The detector should be installed complied with
sensing parts and semi-conductor heat all local codes or NFPA 72 National Fire Alarm
sensing parts in technological structure and Code, NFPA 70 National Electrical Code, BS5839,
circuit structure. It’s applicable to zone 1 EN54.It is installed onto a standard one gang
and zone 2 of areas with explosion-proof electrical box with a mounting hole that have
requirement in petroleum and chemical 6.5cm spacing.
industries. It can match with fire alarm
controller, explosion-proof addressable
interface box, explosion-proof detector and
terminal resistor produced by GST to conduct
the processing of detector signals.
Mounting Hole DZ- 03 Ex

A
B

Intrinsically Safe
Combined Detector
C-9101Ex
K1 K2
O2 O1 I1 I2 Terminal Resistor
I-9332 Interface Explosion-proof Explosion-proof Explosion-proof Explosion-proof

Detector Detector Manual Call Point Detector
Sample wiring diagram above show detectors are connected with I-9333 Interface. There are four
terminals with numbers on the explosion-proof orientation base, “1” is the anode input, “2” is the
anode output, “3” is the power cathode, “4” is null.

Compatible with all GST Intelligent Fire Alarm Panels via I-9332Ex Explosion Proof Interface
(purchased separately)
Box
Intrinsically Safe Combined Smoke and
C-9101Ex 0.221 120
Heat Detector
DZB Intrinsically Safe Detector Base 0.050 360
I-9332 Interface Module 1.5Kg 1

Intrinsically Safe Dual
Heat Detector
C-9103Ex
• Operating Voltage:DC12V to DC24V

Standby Current≤60μA
• Wiring: 1 Pair
• Alarm Confirming LED: Red, not lit
when polling, constantly lit when
alarming.
• Monitoring Area: 30 m2 for space height
not more than 8m.
Temperature: -10ºC+40 ºC
Relative Humidity: ≤95%, no
condensation
• Dimension: Diameter: 100mm, Height:
45mm(excluding the base)
• Safety Barrier Parameters: U0=28V,
I0=93mA
Features and Benefits • Enclosure Protection Grade: IP53
• Material and Color of Enclosure: ABS,
1. Fixed Temperature and Rate of Rise ivory white
Detection • Mounting Hole Distance: 45mm to
2. Twin LED for 360º vision 75mm
3. Low profile design
4. Initiated by fire alarm point using Call Point Installation
I-9332Ex Interface
The detector should be installed complied with
all local codes or NFPA 72 National Fire Alarm
Code, NFPA 70 National Electrical Code, BS5839,
Description EN54.It is installed onto a standard one gang
C-9103 (Ex) Explosion-proof Rate of Rise and electrical box with a mounting hole that have
Fixed Temperature Heat Detector is 6.5cm spacing.
applicable to Zone 1 and Zone 2 of areas with
explosion-proof requirement in petroleum
and chemical industries. It can match with
LD-8332 Interface connected with GST fire
alarm controller, explosion-proof detector to
conduct the processing of detector signals.
Mounting Hole DZ- 03 Ex

A
B

Intrinsically Safe Dual
Heat Detector
C-9103Ex
K1 K2

Sample wiring diagram above show detectors are connected with I-9333 Interface. There are four
terminals with numbers on the explosion-proof orientation base, “1” is the anode input, “2” is the
anode output, “3” is the power cathode, “4” is null.

Box
C-9103Ex Intrinsically Safe Dual Heat Detector 0.220 120
DZB Intrinsically Safe Detector Base 0.050 360

Intrinsically Safe
Manual Call Point
C-9201Ex
• Operating Voltage: 24Vdc

Standby Current: 0mA
• Output Capacity: Rating DC60V/100mA
passive output contact signal, contact
resistance≤100mΩ
• Type of Initiating Part: Reusable
• Reset Mode: Manually resuming by a
sucker
• LED indicator: Red, not lit when normal,
lit after alarming.
• Explosion-proof Marking: ExibIICT6
• Safety Barrier Output Parameters:
Uo+28V, Io=93mA
1. LED indicator • Wiring: 1 Pair
2. Two plug-in constructions allow easy • Operating Environment:
installation. Temperature: -10ºC+50 ºC
3. Utilized independent output contact Relative Humidity: ≤95%, no
4. Initiated by fire alarm point using condensation
I-9332Ex Interface • Mounting Hole Distance: 65mm
• Dimension: 90mm×122mm×48.5mm
Description • Degree of Protection of Enclosure: IP40
• Material and Colour: ABS, red
C-9201(Ex) Explosion Proof Manual Call Point
is designed for the purpose of raising an
alarm manually once verification of a fire or Call Point Installation
emergency condition exists, by pressing the
non breakable glass and alarm signal can be The MCP should be installed complied with all
sent to the controller. After receiving the local codes or NFPA 72 National Fire Alarm Code,
alarm signal, the controller will show the NFPA 70 National Electrical Code, BS5839,
number of LD-8332 Interface connecting with EN54.It is installed onto a standard one gang
the MCP, and vocalize alarm sound. This MCP electrical box with a mounting hole that have
6.5cm spacing.
is intrinsically safe type, is suitable in
inflammable and hazardous places in 65
petroleum and chemical industries.

Intrinsically Safe
Manual Call Point
C-9201Ex
K1 K2

Sample wiring diagram above show manual call point connected with I-9333 Interface. The
terminals I1, I2: to intrinsically safe side of the Safety Barrier.; K1, K2: Normally open output
terminals; while O2, O1: To next MCP.

Box
Intrinsically Safe Conventional Manual
C-9201Ex 0.221 120
Call Point

Intrinsically Safe
Strobe C-9403Ex/ C-9404Ex
Description
The C-9403 (Ex) is an Intrinsically Safe
conventional combined sounder and strobe
while the C-9404 (Ex) is identical in
appearance and features to the C-9404 (Ex)
but without strobe element and are suitable
used for petroleum and chemical industrial.
This Using six highlights LED’s for high
intensity visual alarm to warn the people
especially the persons with hearing
difficulties. The audio efficiency and sound
distribution generate over 94 dB at 1
Features and Benefits meters distance giving an excellent
audibility from the device location.
This conventional electronic wall mounted
1. High intensity and long life LED
device initiated by fire alarm point using I-
cluster
9333Ex Interface (see manual for more
2. High sound level and Low power
information) with safety barrier to make an
consumption
explosion proof system.
3. Initiated by fire alarm control panel
4. Easy installation and connection
Specification
Part Number C-9403Ex C-9404Ex
Sound level output 85 dB to 115 dB
Strobe / Frequency 6 highlight LED; 1.4 Hz± 20% No feature
Explosion Proof Marking Exib□CT6
Tone Modification Period 0.7s ± 20%
Operating voltage Power Supply 24Vdc(16~28Vdc)
Supply current: standby 5mA / alarm current: standby 3mA / alarm 35mA
Operating current
50mA
Wiring 2 wire (polarized)

Intrinsically Safe
Strobe C-9403Ex/ C-9404Ex
The sounder base should be installed Selection of compatible ControPanels
complied with all local codes or NFPA 72 Compatible with all GST Intelligent Fire
National Fire Alarm Code, NFPA 70 National Alarm Panels via I-9333Ex Explosion Proof
Electrical Code, BS5839, EN54.It is installed Interface (purchased separately)
onto a standard one gang electrical box with
a mounting hole that have 6.5cm spacing.
WALL /Kg Qty per
ELECTRICAL
Box
BACK BOX
Intrinsically Safe
C-9403Ex Conventional 0.350 45
MOUNTING
Sounder Strobe
A hK k ff H l
BASE Intrinsically Safe
C-9404Ex Conventional 0.340 45
Sounder Strobe
Wiring and Connection I-9333 Interface Module 1.5Kg 1
Sample wiring diagram below show sounder
connected with I-9333 Interface. The
sounder D1 (+) 9; D2 (-), is for 24VDC
power supply polarized, connected to 3 and 4
of Interface. Each interface can only connect
with one sounder Ex or sounder strobe Ex.
Note that Interface should be installed in the
safety area and the cable must be fire rated
type and the size depends on the distance
and application. Minimum size gauge
1.0mm²(18 AWG)
I-9333 Ex-Interface
3(+)
I-9333Ex L+ 1(+) N F928 Zener
Circuit Board L- 2(-) Safety Barrier 4(-)
D1 D2 Z1 Z2
24VDC Fire Alarm Control Panel
Intrinsincally Safe Loop

Data Sheet GST

Uploaded by

Copyright:

Available Formats

Data Sheet GST

Uploaded by

Copyright:

Available Formats

E-MAIL: hombi@hombi.ru HTTP://GSTRU.RU HTTP://WWW.HOMBI.

Secure and speedy communication through

Drift compensation, to monitor for the long

E-MAIL: hombi@hombi.ru HTTP://GSTRU.RU HTTP://WWW.HOMBI.RU

45mm to 75mm spacing. BASE

FIELD DEVICE PROGRAMMER

MANUFACTURED IN ACCORDANCE WITH

Note: Specifications are subject to change without notice.

E-MAIL: hombi@hombi.ru HTTP://GSTRU.RU HTTP://WWW.HOMBI.RU

Unique pleasing with a low profile design,

Secure and speedy communication through

Electronic addressing and sensitivity

E-MAIL: hombi@hombi.ru HTTP://GSTRU.RU HTTP://WWW.HOMBI.RU

hole of 45mm to 75mm spacing. BASE

FIELD DEVICE PROGRAMMER

Note: Specifications are subject to change without notice.

E-MAIL: hombi@hombi.ru HTTP://GSTRU.RU HTTP://WWW.HOMBI.RU

Secure and speedy communication through

Drift compensation, to monitor for the long

E-MAIL: hombi@hombi.ru HTTP://GSTRU.RU HTTP://WWW.HOMBI.RU

Mounting Standard Base

The detector is mounted using our standard MARK−LINE 2ND MARK−LINE

base DZ-03. Multiple-direction design allows

CONCRETE PAD OR EMBEDDED BOX

HOLE The address of the detector and sensitivity

Connect the wires to the required terminal

Minimum size gauge 1.0mm²(18 AWG)

Selection of compatible Control Panels

detector in the base by the mark-line and

E-MAIL: hombi@hombi.ru HTTP://GSTRU.RU HTTP://WWW.HOMBI.RU

Secure and speedy communication through

Drift compensation, to monitor for the long

E-MAIL: hombi@hombi.ru HTTP://GSTRU.RU HTTP://WWW.HOMBI.RU

Mounting Standard Base

hole of 65mm spacing ROTATE CLOCKWISE

CONCRETE PAD OR EMBEDDED BOX

size depends on the distance and application.

FIELD DEVICE PROGRAMMER

Note: Specifications are subject to change without notice.

E-MAIL: hombi@hombi.ru HTTP://GSTRU.RU HTTP://WWW.HOMBI.RU

Aesthetically pleasing with a low profile

Secure and speedy communication through

Features and Benefits The integral microprocessor analysis the

E-MAIL: hombi@hombi.ru HTTP://GSTRU.RU HTTP://WWW.HOMBI.RU

Mounting Standard Base

The detector is mounted using our standard MARK−LINE 2ND MARK−LINE

HOLE The address of the detector and sensitivity

Connect the wires to the required terminal

size depends on the distance and application.

FIELD DEVICE PROGRAMMER

Compatible with all GST Intelligent Fire

The Intelligent Dual Heat Detector should be Ordering Information:

MANUFACTURED IN ACCORDANCE WITH

Note: Specifications are subject to change without notice

E-MAIL: hombi@hombi.ru HTTP://GSTRU.RU HTTP://WWW.HOMBI.RU

The integral microprocessor analyses the

Secure and speedy communication through

E-MAIL: hombi@hombi.ru HTTP://GSTRU.RU HTTP://WWW.HOMBI.RU

The detector is mounted using our standard

surface mount only, mount onto standard one

CONCRETE PAD OR EMBEDDED BOX ROTATE CLOCKWISE

The address of the detector and sensitivity

Connect the wires to the required terminal

distance and application. Minimum size gauge

FROM CONTROL PANEL TO NEXT DEVICE

Compatible with all GST Intelligent Fire

Detector Installation Ordering Information:

The Intelligent sensor should be installed in Part No Description Weight Pack

clockwise until it reaches the next mark line.

Note: Specifications are subject to change without notice.

E-MAIL: hombi@hombi.ru HTTP://GSTRU.RU HTTP://WWW.HOMBI.RU

The detector is ideally suited to historical