0% found this document useful (0 votes)
97 views4 pages

Assignment On Generation of Computer Send

There are five generations of computers defined based on the underlying technology used. The first generation used vacuum tubes, the second used transistors, the third used integrated circuits, the fourth used VLSI circuits, and the fifth generation uses ULSI technology and focuses on parallel processing and artificial intelligence. Each generation brought increases in speed, reliability and decreases in size and cost compared to the previous generation.
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
Download as pdf or txt
0% found this document useful (0 votes)
97 views4 pages

Assignment On Generation of Computer Send

There are five generations of computers defined based on the underlying technology used. The first generation used vacuum tubes, the second used transistors, the third used integrated circuits, the fourth used VLSI circuits, and the fifth generation uses ULSI technology and focuses on parallel processing and artificial intelligence. Each generation brought increases in speed, reliability and decreases in size and cost compared to the previous generation.
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
Download as pdf or txt
Download as pdf or txt
You are on page 1/ 4

Generations of Computers

Generation in computer terminology is a change in technology a computer is/was being used.


Initially, the generation term was used to distinguish between varying hardware technologies.
Nowadays, generation includes both hardware and software, which together make up an entire
computer system.
There are five computer generations known till date. Each generation has been discussed in
detail along with their time period and characteristics. In the following table, approximate dates
against each generation has been mentioned, which are normally accepted. Following are the
main five generations of computers.
Sl. No. Generation & Description

First Generation
1
The period of first generation: 1946-1959. Vacuum tube based.

Second Generation
2
The period of second generation: 1959-1965. Transistor based.

Third Generation
3
The period of third generation: 1965-1971. Integrated Circuit based.

Fourth Generation
4
The period of fourth generation: 1971-1980. VLSI microprocessor based.

Fifth Generation
5
The period of fifth generation: 1980-onwards. ULSI microprocessor based.

First Generation Computers


The period of first generation was from 1946-1959. The computers of first generation used
vacuum tubes as the basic components for memory and circuitry for CPU (Central Processing
Unit). These tubes, like electric bulbs, produced a lot of heat and the installations used to fuse
frequently. Therefore, they were very expensive and only large organizations were able to
afford it.
In this generation, mainly batch processing operating system was used. Punch cards, paper
tape, and magnetic tape was used as input and output devices. The computers in this generation
used machine code as the programming language.
The main features of the first generation are:

1
• Vacuum tube technology
• Unreliable
• Supported machine language only
• Very costly
• Generates lot of heat
• Slow input and output devices
• Huge size
• Need of AC
• Non-portable
• Consumes lot of electricity
Some computers of this generation were:

• ENIAC
• EDVAC
• UNIVAC
• IBM-701
• IBM-750

Second Generation Computers


The period of second generation was from 1959-1965. In this generation, transistors were used
that were cheaper, consumed less power, more compact in size, more reliable and faster than
the first-generation machines made of vacuum tubes. In this generation, magnetic cores were
used as the primary memory and magnetic tape and magnetic disks as secondary storage
devices.
In this generation, assembly language and high-level programming languages like FORTRAN,
COBOL were used. The computers used batch processing and multiprogramming operating
system.
The main features of second generation are:

• Use of transistors
• Reliable in comparison to first generation computers
• Smaller size as compared to first generation computers
• Generates less heat as compared to first generation computers
• Consumed less electricity as compared to first generation computers
• Faster than first generation computers
• Still very costly
• AC required
• Supported machine and assembly languages Some computers of this
generation were:
• IBM 1620
• IBM 7094
• CDC 1604
• CDC 3600
• UNIVAC 1108

2
Third Generation Computers
The period of third generation was from 1965-1971. The computers of third generation used
Integrated Circuits (ICs) in place of transistors. A single IC has many transistors, resistors, and
capacitors along with the associated circuitry.
The IC was invented by Jack Kilby. This development made computers smaller in size, reliable,
and efficient. In this generation remote processing, time-sharing, multi-programming operating
system were used. High-level languages (FORTRAN-II TO IV, COBOL, PASCAL PL/1,
BASIC, ALGOL-68 etc.) were used during this generation.
The main features of third generation are:

• IC used
• More reliable in comparison to previous two generations
• Smaller size
• Generated less heat
• Faster
• Lesser maintenance
• Costly
• AC required
• Consumed lesser electricity
• Supported high-level language Some computers of this generation were:

• IBM-360 series
• Honeywell-6000 series
• PDP (Personal Data Processor)
• IBM-370/168
• TDC-316

Fourth Generation Computers


The period of fourth generation was from 1971-1980. Computers of fourth generation used
Very Large Scale Integrated (VLSI) circuits. VLSI circuits having about 5000 transistors and
other circuit elements with their associated circuits on a single chip made it possible to have
microcomputers of fourth generation.
Fourth generation computers became more powerful, compact, reliable, and affordable. As a
result, it gave rise to Personal Computer (PC) revolution. In this generation, time sharing, real
time networks, distributed operating system were used. All the high-level languages like C,
C++, DBASE etc., were used in this generation.
The main features of fourth generation are:

• VLSI technology used


• Very cheap
• Portable and reliable
• Use of PCs
• Very small size
• Pipeline processing
• No AC required
• Concept of internet was introduced
• Great developments in the fields of networks

3
• Computers became easily available Some computers of this generation were:

• DEC 10
• STAR 1000
• PDP 11
• CRAY-1(Super Computer)
• CRAY-X-MP(Super Computer)

Fifth Generation Computers


The period of fifth generation is 1980-till date. In the fifth generation, VLSI technology
became ULSI (Ultra Large Scale Integration) technology, resulting in the production of
microprocessor chips having ten million electronic components.
This generation is based on parallel
processing hardware and AI (Artificial
Intelligence) software. AI is
an emerging branch in computer
science, which interprets the means and
method of making computers think like
human beings. All the high-level
languages like C and C++, Java, .Net
etc., are used in this generation.

The main features of fifth generation are:

• ULSI technology
• Development of true artificial intelligence
• Development of Natural language processing
• Advancement in Parallel Processing
• Advancement in Superconductor technology
• More user-friendly interfaces with multimedia features
• Availability of very powerful and compact computers at cheaper rates Some
computer types of this generation are:
• Desktop
• Laptop
• Notebook
• Ultrabook
• Chromebook

You might also like