Scribd
Upload
413 views3 pages

Routine Task Card

This task card provides instructions for cleaning the P8 panel of a Boeing 737-NG aircraft with registration HP-1825CMP and serial number 40780. The work is to be performed at line MEX-01-SV in MEX. The task involves checking that a cleaning kit is installed or deferred in Maintenix, carefully cleaning the panel with a soft brush and wiping away sticky materials, and then restoring the aircraft to normal configuration. Cautions are provided to be careful cleaning switches, buttons, and knobs to avoid damage.

Uploaded by

Adriax
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
413 views3 pages

Routine Task Card

This task card provides instructions for cleaning the P8 panel of a Boeing 737-NG aircraft with registration HP-1825CMP and serial number 40780. The work is to be performed at line MEX-01-SV in MEX. The task involves checking that a cleaning kit is installed or deferred in Maintenix, carefully cleaning the panel with a soft brush and wiping away sticky materials, and then restoring the aircraft to normal configuration. Cautions are provided to be careful cleaning switches, buttons, and knobs to avoid damage.

Uploaded by

Adriax
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd

TASK CARD Date Printed: 02-FEB-2023 07:15 UTC

Page 1 of 2

AIRCRAFT TYPE REGISTRATION S/N WORK PACKAGE # WP DATE LINE #

737-NG HP-1825CMP 40780 TRF7N005K39F 02-FEB-2023 06:31 UTC 2

WORK PACKAGE NAME WORK LOCATION


PLA, MEX-138, SV3+AD CK (01FEB23) MEX/LINE_MEX-01-SV
TASK NAME
JIC Maintenix JIC Revision 10/8/21 10:18 PM
EA 2000-0004C-JIC (STANDARD PRACTICE: P8 PANEL CLEANING (e-DOC)) Revision: 6 Date:

ZONES ACCESS PANELS

211, 212

PARTS ON/OFF
REMOVED INSTALLED
Description
Qty P/N S/N Position Reason Qty P/N S/N

No Parts Required

TOOLS
NAME P/N S/N CHECKED OUT TO
No Tools Required

MEASUREMENTS
PARAMETER VALUE SIGNED_BY
No Measurement Recorded

ACTIONS

DISCREPANCY FOUND
No Additional Faults Found

JOB CARD STEPS


STEP 1 - Pending

NOTE: If kit P/N 3100DA0001C-5 is not installed, check in Maintenix to make sure the kit is already controlled under
an OIL deferral. If the kit is already controlled under
OIL then signoff step 2 as NA and continue with step 3.

If the kit is not installed and is not controlled under OIL and there is not stock availability, open an OIL to install Kit
P/N 3100DA0001C-5 then signoff step 2 as NA and continue with step 3.

CAUTION: Be careful when you are cleaning P8 panel, as you may damage the switches, buttons or knobs.
TASK CARD Date Printed: 02-FEB-2023 07:15 UTC

Page 2 of 2

JOB CARD STEPS


CAUTION:Be careful when you are cleaning P8 panel, as you may damage the switches, buttons or knobs.

SKILL SKILL STATUS WORK PERFORMED CERTIFICATION


MECH Pending
STEP 2 - Pending

Clean the P8 Panel as follows:


"Remove dust, dirt, and foreign matter from the surface with a soft bristle brush
"Wipe to remove any unwanted or Sticky material from the panels

NOTE:To do the above procedure Use Kit P/N3100DA0001C-5, that was placed in maintenance compartment in the
cockpit see figure 2 for illustration, return kit to the maintenance compartment when you finish.

SKILL SKILL STATUS WORK PERFORMED CERTIFICATION


MECH Pending
STEP 3 - Pending

Restore aircraft to normal configuration


SKILL SKILL STATUS WORK PERFORMED CERTIFICATION
MECH Pending
FIGURE 1 – P8 PANEL

You might also like