1. WARNING 3. GETTING ACQUAINTED 4.

BASIC OPERATIONS
GMRS Frequency List:
3.1 Front panel 4.1 Switching the Power On/Off
VFO/Channel mode switch LCD Up 1. Turn the Volume knob clockwise to turn on the radio, the radio LCD will display
Qixiang Electon Science & programmed text and emit a beep sound .
Main channel Down Indicator
Technoloyg Co.,Ltd. 2. Power Off: Turn volume knob anti-clockwise until hear "click" to turn off the radio.

AT-779UV
779UV V/M
4.2 Adjusting the Volume
MIC
MAIN VOL Turn volume knob clockwise to increase colume and anti-clockwise to reduce it.
This device complies with Part 15 of the FCC Rules. Operation is subject to the condition
that this device does not cause harmful interference. MON FUN 4.3 Switch between Main Channel and Sub Channel
1
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled In standby states, press the microphpne key or front panel key to switch
environment. This equipment shall be installed and operated with minimum distance 71.372 Monitor between main channel and sub channel. The top left corner of LCD will display current
Menu
Programming port/ microphone jack main channel .
cm between the radiator & body. Power on, volume switch

For a transmitter that can only be operated with an FCC license,warningss concerning 4.4 Adjust Channel
3.2 Rear panel
PP
T
compliance with applicable licensing requirements and information concerning license 1. Press microphone key or front panel key to switch the radio to channel mode,
applianction procedures. press microphone 【UP】/【DN】 key or front panel / key to choose channel .
SQL
SCAN

1
4

MIC
TOT
7

2. In channel mode, input three numbers by number key to fast choose a channel.
FUN
A

TONE
2
BLK
5
SUB
8
V/M
B

SKIP
3
REV
6
RPT

2. ACCESSORIES
9

4.5 Adjusting Frequency (Europe version only)

MON
POW
LAM

1. By number key: In VFO mode, you can input wanted frequency by the microphone
DIL
D

2.1 Standard Accessories number key. For example if want 145.125Mhz, just press key 1, 4, 5, 1, 2, 5, if want
MIC 145Mhz, just press 1, 4, 5. The input is invalid if the frequency is over range.
1 2 3

Antenna jack External speaker jack

PPT
/
SQL TONE SKIP MON

4 5 6 0

2. By step size: In VFO mode, press microphone 【UP】/【DN】 or front panel

7 8 9
TOT SUB RPT LAM

A B C D
FUN V/M MAIN DIL

Note: To get the best range from the external whip antenna(50Ω　
)should be used. key can change frequency by step size.
779UV V/M Ant:Tx GMRS, Rx:136-174&400-490Mhz, 0dBi . installation is height < 3m. Step size can be programmed by software from 2.5K to 50K.
779UV V/M
MIC

MAIN
MAIN VOL
3.3 Microphone
VOL
MON FUN
4.5 Store channel
Up /Down key
MON FUN In standby states, press the microphpne key , the top left corner will display Func ,
Transceiver Microphone Mobile Bracket
MIC then press 【UP】 KEY , the LCD bottom left corner will display Save to XXX,
now press 【UP】/【DN】 key to choose a channel number, hold key to store the
MIC
Indicator
PTT new frequency and return to standby.
1 2 3

PPT
SQL TONE SKIP MON
» » XXX stands for the channel number, if LCD displays “Null” under “Save TO XXX”,
4 5 6 0
SCAN BLK REV POW

Adjusting screws non-slip mat Fuse(10A 250V) Number key means current channel is empty.

Instruction Manual
7 8 9
TOT SUB RPT LAM

A B C D
FUN V/M MAIN DIL
4.6 Channel Delete
1. In channel mode, press microphone key, then press 【DN】 key, the LCD displays
“Delete XXX” and frequency, presss 【UP】/【DN】key to choose the channel to delete,
www.qxdz.cn Screws Pads manual
hold【# LAM】key delelte to current channel.
» “XXX” stands for the channel number, the LCD displays “Null” after chennel deleted

2 3 4
 4. BASIC OPERATIONS 4. SHORTCUT OPERATION 5. FUNCTION SETTING 5. FUNCTION SETTING 6. SPECIFICAITONS

4.7 Receiving Press microphone key and then press number key TO fast enter following functions, 5.1 By Front Panel Key No. Function name Value GENERAL
Choose a receiving channel or frequency for receiving call, if the RX signal is week, then press【UP】/【DN】key to choose value. presss【PTT】 key or key to Store. Europe version: TX/RX: 144-146MHz , 430-440MHz
1. Press key to enter main menu. 11 Busy channel Lock OFF、REPEATER、BUSY
hold front panel key or microphone key to monitor weak signal. Frequency Range
Function list 2. Press key or key to choose function. USA version: TX/RX: 467.55-467.725MHz
» When the RX icon and field strength flashes, but can not hear the calling, it means 12 Channel name 0~z TX/RX: 462.5625-462.725MHz
current channel receive a matching carrier but unmatching signaling. Refer to No. 3. Press / key to choose value.
Function name Combination Key RX: 136-174MHz , 400-490MHz
CTCSS/ DCS CODE or Optional Signaling setup in Page 6). 4. Press key or key to store and exit. 13 TX OFF ON、OFF
1 Squelch level setting + Europe version: 25K (Wide Band) 12.5K (Narrow band)
» » When setting DCS code, key is for switch between positive and inverse code. Channel Spacing
14 Scramber 1~11、edit、OFF USA version: 12.5K
4.8 Transmitting 2 Optional signaling setting +
15 Compander ON、OFF Phase-locked Step 2.5KHz,5KHz,6.25KHz,10KHz,12.5KHz,15KHz,20
Hold [PTT] and speak into microphone. the radio start transmit, the screen shows red 5.2 By Microphone Key
3 Scan Skip + KHz,25KHz,30KHz,50KHz
TX and field strength. Hold the microphone approximately 2.5-5.0cm from your lips and
speak to microphone in your normal speaking voice to get best timbre. 1. Press key and then press key to enter menu. 16 NC(Noise reduction) ON、OFF
4 Scan + Operating Voltage DC 13.8V±15%
2. Press key or key to choose function.
17 5Tone 1~100, Press PTT to transmit Squelch Carrier/ CTCSS/DCS/5Tone/2Tone/DTMF
4.9 Emergency Alarm 5 Busy channel lockout + 3. Press【UP】/【DN】key to choose value.
18 2Tone 1~32, Press PTT to transmit Frequency Stability ±2.5ppm
In standby, hold key, release it until the LCD displays ALARM, the alarm function 4. Press key to store and exit
6 Frequency reverse + -20℃ ~ +60℃
turns on. Program emergency alarm rule shall be programmed by PC software. » When setting DCS code, key is for switch between Positive and inverse code. 19 Sub channel display FREQ、VOLT、OFF Operating Temperature
7 Time out timer + key is for choose special DCS. 20 Key beep ON、OFF Dimensions(mm) 124x101x36mm
4.10 Keypad Lockout Weight 0.45kg (main unit)
8 Sub channel on/off switch + 21 Time out timer 1~30Min、OFF
In standby, hold key or key , the radio emit Du sound, the LCD displays LOCK. RECEIVER
Now release the key , the keypad is locked. To turn of key lock, hold key or key until
Function list 22 DMTF transmit time 50ms~500ms
9 Offset direction +
the radio emit Du Du, the LOCK icon disappear. now release the key. No. Function name Setting value 23 Squelch level
Wide band Narrow band
OFF、1~9
10 Function Menu + Sensitivity (12dB Sinad) ≤ 0.25μV ≤ 0.35μV
1 TX CTC/DCS 67Hz~254.1Hz、000N~777I 24 Scan pause time 5ST、10ST、15ST、2SP
4.11 Transmit Tone Pulse Frequency 11 Power setting. + Adjacent Channel ≥ 70dB ≥ 60dB
2 RX CTC/DCS 67Hz~254.1Hz、000N~777I 25 LCD brightness 1~5 Selectivity
Hold PTT and [DN] key will transmit selected Pre-programmed tone pulse frequency.
12 LCD brightless + 26 Tone burst frequency 1750Hz、2100Hz、1000Hz、1450Hz
3 TX/RX CTC/DCS 67Hz~254.1Hz、000N~777I Audio Response +1~-3dB(0.3~3KHz) +1~-3dB(0.3~2.55KHz)
4.12 VFO Scan and Channel Scan 13 DTMF Code check + 27 Channel display FREQ、CH、NAME Hum & Noise ≥ 45dB ≥ 40dB
4 Optional signaling OFF、DTMF、2Tone、5Tone
1. VFO scan: In VFO mode, press microphone key or key to start VFO scan . if the 28 Reset FACTORY？ INITIALIZE？ Audio distortion <3%
radio has programm PL1, PH1, ,PL2, PH2, PH2 frequency( in the buttom of channel list), VFO » » In DTMF check mode 5 Squelch mode SQ、CT/DCS、Tone、C&T、C/T Audio power output >2W@10%
scan will between PL1-PL2 and PL2-PH2. When check DTMF code, press PTT will send current DTMF code.
2. Channel Scan: In channel mode press microphone key and then press key to start To revise DTMF code, press key and then press key to enter edit mode. 6 Step size 2.5K~50K TRANSMITTER
channel scan. Channel scan setting shall be programmed by PC software. input DTMF code by number keys , then press PTT to transmit the code and store. Wide band Narrow band
7 Band width WIDE（25K）、NARROW（12.5K）
Power Output VHF: 25/5W, UHF: 20/5W
4.13 FM radio 8 Reverse ON、OFF
Modulation 16KΦF3E 11KΦF3E
Press microphone key or front panel key to switch the radio to channel mode, 9 Talk around ON、OFF
Input FM radio frequency directly by the microphone number keys.
Adjacent Channel Powe ≥ 70dB ≥ 60dB
10 Offset frequency 0~70MHz
Hum & Noise ≥ 40dB ≥ 36dB
Spurious Emission ≥ 60dB ≥ 60dB
Audio Response +1~-3dB(0.3~3KHz) +1~-3dB(0.3~2.55KHz)
Audio Distortion ≤ 5%
6
5 6 7 8