Immunity Test System

According to IEC 61000-4-6

PC-System with
IEEE Control Path immunity Software
and IEEE card
gn all
na
RF
R Siig
F--S
P atth
Pa h Liin
err L
nee
PPo we
ow ne
Liin
ll L e
gn
Siig na
a
r orr S
m p lifie o

RF-A
or
e n erat r
al G No p
Sign D
C lam
-C
EM
m ent
ip
Equ r
de
Un
Test

s r eq uir e m ents we
ing on th e customer ding to IEC
Depend e ms a c c o r
r im m un ity test syst e in struments
offe p ar a t
co n sisting of se
61000 -4 -6
pa ct-tes t-g enerator.
or as a com
 IMMUNITY TEST SYSTEM
General ACCORDING TO IEC 61000-4-6
The immunity of an EUT to conducted RF interference is
tested in the frequency range 150 kHz to 80 MHz (230
MHz) according to IEC 61000-4-6. This applies to all
EUT with at least one circuit connection (power line,
signal line, ground line). During the test process the
Control software
interference is coupled directly onto the lines to be tested.
The control software „CD-LAB“ is the heart of the
complete test system. The software performs the
Contrary to this, when performing immunity tests in the
reference runs and stores the data thereof (see also
frequency range (26 MHz) 80 MHz to 2000 MHz
reference run and test run). It permits manual and fully
according to IEC 61000-4-3, the EUT is exposed to a
automatic tests and prepares the test record. A fully
defined radiated electromagnetic field. More detailed
automatic monitoring of the EUT´s function is reasonable
information is given in our information sheet „Immunity
in all cases where the EUT´s compliance with preset
Test system according to IEC 61000-4-3“.
tolerance limits can be monitored for up to four values to
be measured.
The described immunity test systems are to some extent
composed of the same testing and measuring equipment.
Further essential data of the software:
Therefore, these components have to be acquired only
Microsoft Windows Platform (WIN 95, WIN 98,
once.
WIN NT)
Simple operator´s guide
On-line help function
Presentation of the results in on-line graphics
Export function of the files for further processing under
Test Assembly
Microsoft Word or Microsoft Excel
The test system for susceptibility testing is in conformity
Step width, test voltage and frequency range to be
with the following Standards: IEC 61000-4-6,
selected at discretion
EN 61000-4-6l. It should be located on a well-grounded
Control of test assembly by IEEE-488 bus and
metal plate and be composed of the following equipment:
RS232 bus
Customized modifications possible

Signal generator
Control computer RS 232
A commercial signal generator is used as signal source.
with IEEE card
(National Instruments) It should cover at least the required frequency range from
GPIB
RF-out
150 kHz to 80 MHz (230 MHz) and allow an amplitude
RF Power-meter
Signal generator Frankonia PMS
modulation of the test signal with a sine wave of 1 kHz
RF-in RF-in
Amplifier Frankonia,
RF-out
and 80 %, as requested by the Standards. Besides, it
type FLL
AE EUT 150/50 ohm should meet the requirements regarding frequency step
Coupling/Decoupling adapter
150/50 ohm
adapter
Network CDN
or EM clamp width. If the equipment supports the use of further
terminated with
50 ohm (1) modulation depths and procedures, as well as frequency
step widths, this is an advantage because it is then
(1)
Some types of CDN do not require a 150/50 ohm adapter with 50 ohm termination
at the AE-side. It depends on the decoupling of the CDN.

Block diagram 1: Set-up of a test system acc. to IEC 61000-4-6 for determination of the reference data.
perfectly equipped for the future, in case the Standards
should be modified in this respect. The main data of a
typical signal generator are as follows:
Frequency range: 9 kHz- 1,0 GHz
Level range: -140 dBm to +13 dBm
Control computer
Frequency resolution: 1 Hz
A commercial IBM compatible PC and Microsoft Windows
Level resolution: 0.1 dB
95 or higher can be used with Pentium processor, with at
Amplitude modulation: 0 to 99.9 %
least 16 Mbyte RAM memory and a screen resolution of
Further modulation types: frequency modulation, phase
800 x 600. For controlling the test system it is necessary
modulation, pulse modulation
to have a GPIB interface card (IEEE-488) of „National
Interface: GPIB (IEEE-488)
Instruments“ installed.
 IMMUNITY TEST SYSTEM
ACCORDING TO IEC 61000-4-6

Table 1 Survey of the most important coupling units:

Type Description
RF Power amplifier M1, M2, M3, M5 1, 2, 3 or 5 power lines
M2/M3 2/3 power lines combination
The software controls the level of the signal generators
S1/50, S1/75, S1/93 Shielded cables; 1 line
output with respect to the frequency. The voltage level impedance 50; 75; 93 (Ohm)
available is then increased by the power amplifier to S2, ..., S36 Shielded cables; 2,..., 36 lines
reach the test voltage required. It depends on the testing AF2, AF3, AF4, AF8 Unshielded cables, asymmetrically operated,
set-up (see coupling units) and the test level/test voltage 2, 3, 4, and 8 lines
T2, T4, T8 Unshielded cables, symmetrically operated
(1V, 3V, 10V or special requirements, e.g. 100V)
2, 4, 8 lines
whether an amplifier output of 25W, 75W or 125 W is
required.
Main data:
RF Power probe / Voltmeter probe
Type: Frankonia FLL 25, FLL 75, FLL 125
Just as the calibration installation, the RF voltmeter probe
Frequency range: 10 kHz - 230 MHz
type Frankonia PMS is
Nominal output: 25W, 75W, 125W
required only if the user
Feeding for nominal output: 1.0 mW (0dBm)
himself wants to carry
Impedance: 50 Ohm
out the reference run of
Use for: CDN, EM coupling clamp
the coupling installation.
In this case, the
generated test voltage is
measured and transmitted
to the control computer.
Main features:

Type: Frankonia PMS

Frequency range: 100 kHz to 1 GHz
Measuring range, at least: 100nW - 0.5W
(-40dBm...+27dBm)
Impedance: 50 Ohm
Coupling units / coupling clamp Interface: RS 232
By means of the coupling units the test voltage is
superimposed on the mains supplies, data lines or signal
Reference Run
lines of the EUT. The technical construction of a coupling
The components of the testing set-up (amplifier, cables,
unit for the respective types of lines to be tested is
coupling unit) show non-linearities over the frequency
prescribed by the Standard. Different coupling units are
range 150 kHz to 80 MHz (230 MHz). For this reason,
used for example for 1, 2, 3 and 5 wire circuits or for
a reference run has to be performed once for each
data and signal lines. The types of coupling units have to
equipment combination required, as well as for each
be determined individually for each customer.
desired test voltage. The set-up for the reference run is
shown in block diagram 1. To perform this run, a
When using the classic coupling units (CDNs Coupling/
calibration unit is required which has been adjusted to
Decoupling Networks) the lines to be tested have to be
the respective coupling unit. During the reference run the
separated. This is mostly impossible and unreasonable with
respective output level of the signal generator is determined,
data and signal cables with e.g. more than 4 lines. In these
at which the requested test voltage (without modulation)
cases the EM coupling clamp can be used, in which the
is available at the coupling unit. This is done in step width
cable to be tested is put in. The disadvantage of the
of 1 %, defined in the Standard, over the whole frequency
coupling clamp consists in the fact that a higher amplifier
range. A new reference run must be performed only if
output is required for obtaining the desired test voltage. To
new components are to be used in the test system, or
generate a test voltage of 20V the EM coupling clamp
within defined calibration intervals. As an alternative to
requires 75W amplifier whereas a 25W amplifier is fully
this, we offer a calibration service.
sufficient when using coupling units.
 Test run
The testing set-up is described in block diagram 2. On the
basis of the reference data determined for the testing set-
up, the required test level and/or test voltage is adjusted
reproducibly in the test run by means of the control
software for each frequency step. For this purpose, the
Control computer
with IEEE card
signal is amplitude-modulated with a sine wave 1 kHz /
(National Instruments)
80 %. The verification of the EUT´s function is performed
GPIB
RF-out
manually (optically) or, if possible, automatically. In the
Signal generator
latter case the EUT´s function is tested by means of max.
RF-in RF-in
Amplifier Frankonia, 4 measuring values with respect to its compliance with
type FLL RF-out
EUT =
Equipment under test
preset tolerance values. The determined data, the results,
AE = Coupling/Decoupling
Additional equipment
e.g.:
Network CDN
Isolation
a description of the test system as well as a comment
or EM clamp
power supply
Ground connection regarding the measurement are summarized by the
Isolation

Metal plate
software in a measuring record. The output is realized by
a printer connected to the PC. The data can be exported
Block diagram 2: Set-up of a test system acc. to IEC 61000-4-6. for further processing in other data processing programs,
e.g. Microsoft Word and Microsoft Excel.

Frankonia Headquarter:
Rambacher Straße 2 . D-91180 Heideck . Germany
Phone ++ 49 (0) 9177/98 500 . Fax ++ 49 (0) 9177/98 520
http://www.frankonia-emc.com . e-mail: info@frankonia-emc.com

S.I.D.T.-EUROPE:
14 rue Albert Einstein . CHAMPS SUR MARNE . France
Phone ++33 (0) 1 64 68 06 04 . Fax ++33 (0) 1 64 61 62 12
e-mail: sidt.europe@wanadoo.fr F R A N K O N I A
Frankonia EMV Mess-Systeme:
Weiherweg 14 . 96199 Zapfendorf . Germany
Phone ++ 49 (0) 95 47/94 01 0 . Fax ++ 49 (0) 95 47/94 01 20 F R A N K O N I A
http://www.frankonia-emc.com . e-mail: frankonia.emv@t-online.de E M V- M e s s - S y s t e m e G m b H