Quick Installation Guide

Ribbon installation
Parts name of a printer

LED indicator

feed button

Rear extemal label

entrance chute

Centronics interface (1) Open the top cover by pressing the (2) Insert ribbon paper core onto (3) Align the notches on the left side
open button on both sides. Then lift ribbon rewind hub. and mount onto the spokes.
the top cover to the maximum open
angle.
power switch USB interface
Ethernet Interface
Top cover open tab
Power jack socket RS-232C interface
Micro SD card socket

Note:
The interface picture here is for reference only .Please refer to the product specification tor the interfaces
availability.

Print head

Priner top cover

Ribbon supply spindle

(4) Press the open button of print head. (5) Insert the ribbon paper core onto (6) Align the notches on the left side
ribbon supply hub. and mount onto the spokes.

Media holder

Ribbon supply gear

Indicator
FEED button
Media bar
Gap sensor

Ribbon rewind gear

Media stator
Ribbon rewind hub

Paper supply hub

(7) Crossing print head, Stick the (8) Turn the ribbon rewind hub until (9) Press down to close the print head, in
Print head release button accordance with the direction that the
ribbon onto the ribbon rewind paper the ribbon plastic leader is thoroughly arrows in the picture indicate. In order to
core and insert the paper core onto the wound and the black section of the guarantee the print quality, please check
rewind smoothly. ribbon covers the print head. and make sure the print head is closed
completely.
Platen roller Media guides

Black mark sensor

01 02
Paper installation Button functions
(1)Feed labels
When the printer is ready, press the button to feed one label to the beginning of the next label.
(2)Pause the printing job
When the printer is printing, press the button to pause a print job, when the printer is pause the Led will be green blinking,
Press the button again to continue the printing job.

Printer diagnostic tool

The Diagnostic Tool is a toolbox that allow users to explore the printer's settings and status; change a printer’s settings ;
download graphics, fonts, and firmware, create a printer bitmap font, and to send additional commands to the printer,
using this convenient tool, you can explore the printer status and settings and troubleshoot the printer.

Start the Diagnostic Tool

(1)Open the printer top cover by pressing (2) put the paper roll into the middle of the (3) Place the paper roll onto the paper roll
(1) Double click on the Diagnostic Tool icon to start the software.
the top cover open tabs located on each label spindle and fix it. mount. (If your paper width is 4 inch,Can Diagnostic Tool.exe

side of the printer. be removed from the fixed piece, direct (2) There are four features (Printer Configuration, File Manager, Bitmap Font Manager,Command Tool) included in the
paper scroll .) Diagnostic utility. Interface

Features tab
Printer status

printer functions
Printer setup

(4) Push the print head release button to (5)Feed the paper printing side face up, (6)Close the print head mechanism by both
open the print head mechanism. through the media bar,media sensor and place hands and make sure the latches are
the label leading edge onto the platen roller. engaded securely.
Move the media guides to fit the label width.

(7)Use“Diagnostic Tool” to set the media sensor type and calibrate the selected sensor.(Start the “Diagnostic Tool” →
Select the “Printer configuration”tab →Click the “Calibrate Sensor”button) please refer to the diagnostic utility quick
start guide for more information.
(3) The detail function in the Printer Function Group are listed as below
Note: Please calibrate the gap/black mark sensor when changing the media. Function Description
Calibrate Sensor Calibrate the sensor specified in the printer setup group media sensor field

Label installation of ribbon and media Ethernet Setup Setup the IP address, subnet mask, gateway for the on board Ethernet
RTC Setup Synchronize printer Real Time Clock with PC
Factory Default Initialize the printer and restore the settings to factory default
Reset Printer Reboot the printer
Print head
Ribbon rewind hub Print Test Page Print a test page

Ribbon Configuration Page Print printer configuration

Paper core
Dump Text To activate the printer dump mode
Ignore AUTO.BAS Ignore the downloaed AUTO. BAS program
Gap sensor Media guide
Media Ribbon path Password Setup Set Diag Tool password
Media path(Outside wound)
Platen roller Exit Line Mode Leave Line mode
Media path(Inside wound)

Black mark sensor Media bar

* For more information and features about this printer, please refer to User's Manual inside the CD disk.
* Specifications, accessories, parts and programs are subject to change without notice.
03 04