TideStation Permanent Operating Manual 0741825b

TideStation Permanent
Operating Manual
Document Ref: 0741825b (Permanent)

Date: 05 November 2018
This document was prepared by the staff of Valeport Limited, the Company, and is the property of the
Company, which also owns the copyright therein. All rights conferred by the law of the copyright and by
virtue of international copyright conventions are reserved to the Company. This document must not be
copied, reprinted or reproduced in any material form, either wholly or in part, and the contents of this
document, and any method or technique available therefrom, must not be disclosed to any other person
whatsoever without the prior written consent of the Company.
Valeport Limited
St Peters Quay
Tel: +44 1803 869292
Totnes
e mail: sales@valeport.co.uk
Devon, TQ9 5EW
Web: www.valeport.co.uk
United Kingdom
As part of our policy of continuous development, we reserve the right to alter, without prior notice, all
specifications, designs, prices and conditions of supply for all our equipment.
Table of Contents
Table of Contents
1. Safety..................................................................................................................................... 4
1.1. Graphical Symbols
....................................................................................................................................
for Use on Equipment 5
2. Introduction
..................................................................................................................................... 6
2.1. Description .................................................................................................................................... 6
2.2. TideStation Permanent
....................................................................................................................................
Features 6
2.3. Sensor Specifications
.................................................................................................................................... 14
2.4. EU Declaration....................................................................................................................................
of Conformity - CE Marking 15
3. Operation
..................................................................................................................................... 19
3.1. Setting Up .................................................................................................................................... 19
4. Data..................................................................................................................................... 27
4.1. Logged Data (Pressure
....................................................................................................................................
Tide & Met) 27
4.2. Logged Data ....................................................................................................................................
(Pressure Tide & CT) 28
4.3. Logged Data ....................................................................................................................................
(Radar Tide and Met) 29
4.4. Logged data ....................................................................................................................................
(Radar Tide and CT) 30
4.5. Real Time Data
....................................................................................................................................
- NMEA 31
5. SATEL
.....................................................................................................................................
- M3 - TR1 35
5.1. Specification .................................................................................................................................... 36
5.2. Safety Note .................................................................................................................................... 38
5.3. Approvals .................................................................................................................................... 40
6. Victron
.....................................................................................................................................
Energy Solar Charge Controller 41
6.1. Important Safety
....................................................................................................................................
Instructions 42
6.2. Installation .................................................................................................................................... 42
6.3. Trouble Shooting
.................................................................................................................................... 45
6.4. Specification .................................................................................................................................... 46
6.5. Configuration.................................................................................................................................... 48
7. Scannex
.....................................................................................................................................
ip.Buffer 50
7.1. Specification .................................................................................................................................... 52
7.2. GPRS Operation
....................................................................................................................................
with a Cellular/Mobile Network 53
7.3. Fitting Batteries
.................................................................................................................................... 54
7.4. Front Panel LED
.................................................................................................................................... 55
7.5. Approvals .................................................................................................................................... 56
Page 2
Table of Contents
7.6. Changing GPRS

....................................................................................................................................
APN Settings 58
7.7. Changing the....................................................................................................................................
SIM Card 64
8. Cable
.....................................................................................................................................
Details 68
8.1. Instrument Cables
.................................................................................................................................... 68
8.2. Internal Loom....................................................................................................................................
Cables 70
Page 3
0741825b - TideStation Permanent Operating Manual
1. Safety
Throughout this manual there are specific and general safety notices.
The following notices must be viewed with particular consideration.
· In order to comply with FCC and IC RF exposure compliance requirements,

maximum antenna gain is 14 dBi and a separation distance of at least 1 meter
must be maintained between the antenna of this device and all persons. The
device must not be co-located or operating in conjunction with any other
antenna or transmitter.
· The TideStation contains a Lead Acid battery that can be charged using Solar
PV or DC voltage inputs. All sources of power should be disconnected from
the TideStation before opening the enclosure.
- See specific safety notices for Lead Acid Batteries - Lead Acid Battery Safety
Statement.
· Only ever use rechargeable Lead Acid Batteries in the TideStation.
· The enclosure should be locked when in operation to prevent unauthorised
access. There is a risk of electric shock.
· The Vitron Energy Solar Charge Controller Cautionary Warnings are found in
Victron section of the manual Important Safety Instructions.
· The Scannex ip.Buffer, if fitted, Cautionary Warnings are found in Scannex
section of the manual GPRS Safety Precautions
· The TideStation Permanent is heavy. Special attention must be given to lifting

and transporting the TideStation.
· Install at a location where there is no risk of the TideStation falling.
· When installed on location ensure all fixings are sufficient to safely survive all
environmental conditions.
· The safety of any system incorporating the TideStation is the responsibility of the assembler of the
system.
· If the TideStation is used in a manner not specified by the manufacturer, the protection provided
by the equipment might be impaired.
© 2018 Valeport Ltd Page 4

Safety
1.1. Graphical Symbols for Use on Equipment

Number Symbol Reference Description
1 IEC 60417-5031 (2002-10) Direct Current
2 IEC 60417-5032 (2002-10) Alternating current
Both direct and alternating
3 IEC 60417-5033 (2002-10)
current
4 IEC 60417-5032-1 (2002-10) Three-phase alternating current
5 IEC 60417-5017 (2006-08) Earth (ground) Terminal
6 IEC 60417-5019 (2006-08) Protective conductor terminal
7 IEC 60417-5020 (2002-10) Frame chassis terminal
8 Not used
9 IEC 60417-5007 (2009-02) On (power)
10 IEC 60417-5008 (2009-02) Off (power)
Equipment protected
throughout by Double
11 IEC 60417-5172 (2003-02)
Insulation or Reinforced
Insulation
Caution, possibility of electric
12 IEC 60417-6042
shock
13 IEC 60417-5041 (2002-10) Caution hot surface
14 ISO 7000-0434B (2004-01) Caution
In position of a bi-stable push

15 IEC 60417-5268 (2002-10)
control
Out position of a bi-stable push
16 IEC 60417-5269 (2002-10)
control
17 ISO 361 Ionising Radiation
Page 5 © 2018 Valeport Ltd

2. Introduction
2.1. Description
The TideStation is a self-contained Tidal Observation solution packaged to optimise performance, be
flexible in its configuration and simple to install and maintain.
TideStation has TideMaster at its core - Valeport’s industry leading Tide Gauge system. Offering
Pressure, Radar and hybrid tidal observation techniques coupled with interfaces to other
meteorological and 3rd party systems. All data can be recorded locally and broadcast to a central
command and control point as required.
Within the TideStation enclosure you will find all required ancillary infrastructure to maintain power
to the Tide and Met equipment interfaced and your chosen telemetry system whether it be radio or
GSM based.
2.2. TideStation Permanent Features

There are 2 standard TideStation Permanent variants
0741020-0 IP64 TideStation enclosure and Internal frame
power loom, Solar PV charging and comms
0741020-4i/p IP64 TideStation enclosure and Internal frame
TideStation Junction Box, power loom, Solar PV charging and wiring for:
TideMaster tide gauge and associated sensors
4 port ip.Buffer and optional Satel UHF radio and antennae
The unit as described above (0741020-XX) does not include a TideMaster, sensors, telemetry
equipment, battery or solar panels which should be ordered separately
2.2.1. Enclosure
· IP64 (not certified as safe for pressure washing)
· Power:
- 12 to 28 V DC input
- Lead Acid battery module (38Ahr)
- 12V Regulator for solar charging
· Fittings for:
- TideMaster
§ pressure\radar sensor
- Dual telemetry options
(UHF/GSM/ip.buffer -4 port)
- Auxiliary Comm ports
· Pressure relief valve

Introduction
2.2.1.1. TideStation Enclosure - External Dimensions

2.2.2. TideStation Schematics
TideStation Junction Box (0741503) Link settings:

Introduction
2.2.2.1. Type - 0741020-ip4 Configuration

2.2.2.2. Fully Specified with TideMaster GSM and Radio Telemetry

Introduction
2.2.2.3. TideStation Permanent External Connectors

2.2.2.4. Type - 0741020-0 Base Unit

TideStation Type 0 is an OEM enclosure equipped with power supply and battery charging hardware
along with serial connectivity, only.
Please contact Valeport for further information.

Introduction
2.2.2.5. Type 0 External Connectors

Connector ports crossed out are plugged and have no connector fitted

2.3. Sensor Specifications

Pressure Transducer Option
Type: Vented strain gauge
with stainless steel mounting bracket
Range: Standard 10dBar (~10m), with 20m cable
Other ranges and lengths available
Accuracy: ±0.1% of full scale.
Radar Level Sensor Option (see VRS-20 data sheet for full details)
Minimum Range: 0.8 m
Maximum Range: 20 m
Beam Angle: ±6°
Frequency: 25 GHz
Accuracy: ±10 mm
Precision: 1 mm
Weather Sensor Options

WindSonic Ultrasonic Anemometer
Wind Speed: 0-60m/s
Wind Direction: 0-359°
Calibration: Held within sensor.
Dimensions: 142mm x 160mm.
METPak II TM Weather Station

Wind Speed: 0-60m/s
Wind Direction: 0-359°
Air Temperature: -35°C to +70°C
Relative Humidity: 0 – 100% RH
Barometric Press: 600 – 1100 hPa/mbar
Dew Point: As per temperature range
Calibration: Held within sensor.
Dimensions: 142mm x 274mm.
To interface other sensor packages please contact Valeport for details

Introduction
2.4. EU Declaration of Conformity - CE Marking

2.4.1. Radio Equipment Directive 2014/53/EU
Radio Equipment Directive 2014/53/EU Standards
EN 60950-1:2006+A2:2013
Safety & Health EN 61010-1:2010
(Article 3.1a) EN 62311:2008
EN 62479:2010
EN 301 489-1 V2.1.1
EN 301 489-5 V2.1.1
EMC
EN 301 489-17 V3.1.1
(Article 3.1b)
EN 301 489-52 V1.1.0
EN 61326-1-2013 (Basic and Industrial Level)
EN 300 113 V2.2.1
EN 300 328 V2.1.1
Radio Spectrum
EN 301 511 V12.5.1
(Article 3.2)
EN 301 908-1 V11.1.1
EN 301 908-2 V11.1.1
2.4.1.1. Approved Antennae

Antenna name Manufacturer Comment Gain
(GSM)
CELLBASE2 Badland PENTABAND END FED 3dbi
DIPOLE
Colinear Omni-
FUC3 Radio Structures 3dB
directional

2.4.2. Environmental
· RoHS Compliance
RoHS Directive 2011/65/EU Standards
Prevention
BS EN 50581:2012
(Article 4.1)
· WEEE Compliance
End of Life Disposal Instructions (WEEE)
For disposal instructions see https://www.valeport.co.uk/Portals/0/Docs/Valeport-B2B-
Compliance.PDF
2.4.3. Export Control

· UK
- ECO Classification NLR (No License Required)

Introduction
2.4.4. CE Certificate

2.4.4.1. Approved Antenna

Operation
3. Operation
The TideStation should always be stored with the Battery Isolation switch in the OFF position and the
TideMaster turned off.
During the installation the battery isolation switch should be OFF and it is strongly recommended
that the battery is not installed until the TideStation is fixed in its final location.
If a telemetry system is to be operated with the TideStation the antenna should be fitted before
power is applied, if a radio is powered up without an antenna, damage may result.
Once the battery is installed, see section Battery Installation, for instructions on how to set the system
to work.
3.1. Setting Up
3.1.1. TideMaster
See Operating Manual - 0741822nn TideMaster Operating Manual for full details on how to set up
and operate the TideMaster.
3.1.2. VRS20 Radar Level Sensor

See Operating Manual 0745813 - VRS20 Radar Level Gauge Operating Manual for full details on how
to set up and operate the VRS20 level gauge.
3.1.3. Scannex IP-Buffer

Please refer to the specific Scannex manual for the model installed in your TideStation for detailed
operational instructions.
Please contact Valeport Support for assistance with configuration and operation of a Scannex
ip.Buffer
support@valeport.co.uk

3.1.4. Satel UHF Radio

Please refer to the specific Satel manual for the model installed in your TideStation for detailed setup
instructions.
Also see Valeport Manual - 0741836 UHF Telemetry Manual for further details on operation of the
Satel Radio with TideMaster.
Using the provided configuration software from Satel ensure the setup is as follows (unless you have
specifically been instructed to configure the radio differently).

Operation
In the UK the maximum permitted transmit power is 500mW

Please ensure that all national and local regulations are strictly adhered to

3.1.5. Powering the TideStation

A 38Ah battery is fitted as standard in the TideStation Permanent where as a 24Ah battery is fitted to
the Portable variant. The lead acid battery is normally sourced locally to reduce shipping weight and
costs.
The TideStations have been designed to work with an external Solar PV Panel (min 55W) with an
internal solar regulator charging a lead acid battery.
The DC input should not be connected directly to a DC distribution network without adequate
surge protection.
The Battery Isolation switch, as its name implies, isolates the battery but does not switch the
TideStation off. If a power source is still available and the Battery Isolation switch is OFF power will
still be available to the TideMaster and Telemetry systems in the TideStation.
As the TideStation contains a large battery and can be used with solar PV panels it should be
locked when in operation to prevent unauthorised access.
The Battery Isolation switch must be switched ON for the battery to be charged.
The Battery Isolation switch module contains a 15A fuse in both the Permanent and Portable systems
There is a 5A fuse in TideStation Junction Box
There is a 20A fuse in Victron Solar Controller
3.1.5.1. Battery Installation
1. Disconnect any external supply

2. Set the battery isolation switch to OFF (0)
3. Ensure the TideMaster is switched OFF
4. Fit the battery and ensure it is fully secured
5. Fit the battery cables

Operation
3.1.5.2. Lead Acid Battery Safety Statement

Installation
Can be installed and operated in any orientation except permanently inverted.
Handles/Weight
Lead Acid batteries can be heavy. They must not be suspended by their handles (where fitted).
Always be aware of safe lifting practices when transporting.
Vent valves
Each cell is fitted with a low pressure release valve to allow gasses to escape and then reseal.
Gas release and Fire

· VRLA Batteries emit hydrogen gas which is highly flammable and will form explosive mixtures in air
from approx 4% to 76%. This can be ignited by a spark at any voltage, naked flames or other
sources of ignition.
· Batteries in use will be part of an electrical circuit and must be isolated from the power source
before attempting to put out a fire. Switch the power OFF before disconnecting the batteries from
the power source.
· Damaged batteries may expose negative plates (grey) colour, which may ignite if allowed to dry
out. These plates may be wetted down with water after the battery has been removed from all
electrical circuits.
· Suitable Extinguisher types: CO2; Foam; Dry Powder.
· Unsuitable Extinguisher types: Water extinguishers must never be used to put out an electrical fire.
· Hazardous decomposition products: Carbon monoxide, Sulphur Dioxide, Sulphur Trioxide, lead
fume and vapour, toxic fumes from decomposition of battery case materials.
· Special protective equipment for fire fighters: Full face visor or safety goggles; respiratory
protective equipment or self-contained breathing apparatus; full acid resistant protective clothing
must be worn in fire fighting conditions.
Temperature
Stable operation is achieved within the operational temperature range -20 to +50 °C.
Do not charge VLRA Batteries above + 50 ºC, discharge or store above + 60 ºC.
Recycling
VRLA batteries must be recycled at the end of life in accordance with local and national laws and
regulations
Battery Acid
The Hazard
Batteries contain Sulphuric Acid which may leak for various reasons. Also acid may be given off as
droplets and/or spray/mist during recharge.
Sulphuric Acid is a corrosive and poisonous liquid which will cause burns and irritation to the skin
and eyes and could severely damage clothing.
Refer to Health & Safety Executive Guidance Note EH40 for the latest occupational exposure limits
for acid mist in air.
Precautions

· Always handle batteries with care

· Never overfill with acid
· Always store upright
· Never allow children access to a battery
· Always charge in a well ventilated area
· Never allow battery vents to become blocked
· Always wear eye protection
· Always wear protective clothing
Accident or Emergency Action and Treatment

Skin contact –
Immediately soak the affected area with copious amounts of clean water, remove any contaminated
clothing and seek medical attention if irritation persists.
Eye contact –
Immediately irrigate eyes for at least 10 minutes with clean water, seek medical attention.
Ingestion –
Immediately drink as much water as possible – do NOT induce vomiting, seek urgent medical
attention.
Spillages –
For small spillages wash away with large quantities of water. For larger volumes dispose of in suitable
acid resistant containers, clearly labeled.
Electrical Energy
The Hazard
Accidental short circuit of battery terminals by a conductive object, such as a metal tool or item of
jewelery etc. may generate sufficient heat to cause severe burns, create arcing or cause any metal to
melt and splash.
Precautions
Always remove metal objects from hands, wrists & neck e.g. rings, bracelets, watches & necklaces.
· Switch off all electrical loads
· Refer to manufacturer’s handbook
· Make the first disconnection and the last reconnection the earth point as far from the battery as
possible
Always take great care to avoid shorting the live terminal to earth.
Never place tools or metal objects near to or on top of a battery.
Burns
Apply a dry sterile dressing and seek medical treatment.
Electric shock
Approach person with care. If the individual is clear of the conductor then, with caution, switch off
equipment or break the current. If the individual is still attached to the conductor do not touch with
bare hands. If possible use a suitable insulating material e.g. wood, rubber, plastic or rolled paper, to
detach the conductor from the victim. If necessary, summon assistance then give artificial respiration
until it arrives.

Operation
Emission of Gases
The Hazard
Hydrogen gas emitted during charging is explosive at concentration levels above 4%. Hydrogen &
oxygen gases are both evolved during battery recharging. These gases may also be emitted at other
times, for example, if the battery is moved or shaken.
Precautions
· Always charge in a well ventilated area
· Always ensure the charging leads are correctly fitted
· Always ensure the PV array is disconnected first, before disconnecting the charging leads
· Always use eye protection and protective clothing
· Always wait at least 5 minutes after ceasing recharge before disconnection
· Always take care to ensure that cables and connections are handled in a way that avoids accidental
sparking
· Static electricity can provide an ignition source for hydrogen gas within a battery. Static charge can
build up on an open circuit battery if, for instance, it has been rubbed against man-made fibres.
Where possible minimise static build up and always wear protective clothing when handling
batteries
Never smoke near a battery

Never allow naked flames near a battery
Never create sparks near a battery

Seek medical advice as appropriate to injury.
In an explosion acid will have been sprayed and ejected and plastic & metal parts may have caused
severe lacerations.
Weight
The Hazard
Batteries are awkward and heavy to handle resulting in possible strains to the human body as well as
potential for dropping the battery, with resultant acid spillage, injury etc.
Precautions
Always use correct lifting procedures to minimise strain to the human body.
Always use lifting handle or lifting ledges if available on the battery.
Seek medical advice as appropriate to the injury. Remember that acid may have been spilled.
Repairing of Damaged Batteries

No attempt should ever be made to renovate or repair a damaged battery.

Disposal of Batteries & Associated Waste

All spent batteries and waste arising from spillages and fires must be disposed of in conformance
with the Environmental Protection Act, the Special Waste Regulations 1996 and the Environmental
Protection (Duty of Care) Regulations 1991.
Yuasa offer a complete battery disposal service.
For further information please contact us at:
Tel: +44 (0) 1793 833555
Email: enquiries@yuasaeurope.com
REACH Regulation (EC) No 1907/2006

Registration, Evaluation, Authorisation and Restriction of Chemicals Industry is required by REACH to
evaluate and manage the risks posed by chemicals, and to provide safety information to product
users.
Information on up-to-date additions to the Substances of Very High Concern (SVHC) Candidate List
is available from the ECHA (European Chemicals Agency) web site: www.echa.europa.eu

Data
4. Data
The TideStation can be configured to use a number of Telemetry methods. The file format of the
data transmitted will be as the TideMaster is configured.
4.1. Logged Data (Pressure Tide & Met)

Firmware version: 0741709nn
File Creation Date: 23/01/2018 14:27:23
Battery Level: 5.7
TideMaster S/N: 3
Station ID: 01
Site info: Valeport test site!
Calibrated: 18/07/2012
Mode: B1
Pressure units: m
output format: TIDEMASTER
User Pressure cal:
Gain: 1.234000
Offset: 1.000000
Vale Pressure cal:
P0: -4.353197e-10
P1: 0.003194
P2: -1.795884
Wind speed units: Knots
Air Pressure units: mBar
Air Temperature units: DegC
Time Stamp [TAB] Depth [TAB] Depth SD [TAB] Wspeed [TAB] Wspeed SD [TAB] Max Gust
[TAB] Wdir [TAB] Wdir SD [TAB] Air Pressure [TAB] Air Pressure SD [TAB] Air Temperature
[TAB] Air Temperature SD [TAB] Dewpoint [TAB] Dewpoint SD [TAB] Humidity [TAB] Humidity
SD [TAB] Batt Status.
When interfaced to a Gill MaxiMet instrument the wind direction reported is corrected.

4.2. Logged Data (Pressure Tide & CT)

Battery Level: 5.7
TideMaster S/N: 3
Station ID: 01
Site info: Valeport test site
Mode: B1
Pressure units: m
User Pressure cal:
Gain: 1.234000
Offset: 1.000000
Vale Pressure cal:
P0: -4.353197e-10
P1: 0.003194
P2: -1.795884
Water Temperature units: DegC
Water Conductivity units: mS
Time Stamp [TAB] Depth [TAB] Depth SD [TAB] WaterTemp [TAB] WaterCond [TAB] Batt Status

Data
4.3. Logged Data (Radar Tide and Met)

Battery Level: 9.1
TideMaster S/N: 3
Station ID: 01
Site info: Valeport test site
Mode: B1
Pressure units: m
Radar:
Min limit: 0.500
Max Limit: 2.000
Datum: 2.000
Pre amble: 4
Wind speed units: Knots
Air Pressure units: mBar
Air Temperature units: DegC
Time stamp [TAB] Depth [TAB] Depth SD [TAB] Wspeed [TAB] Wspeed SD [TAB] Max Gust
[TAB] Wdir [TAB] Wdir SD [TAB] Air Pressure [TAB] Air Pressure SD [TAB] Air Temperature
[TAB] Air Temperature SD [TAB] Dewpoint [TAB] Dew point SD [TAB] Humidity [TAB] Humidity
SD [TAB] Batt Status

4.4. Logged data (Radar Tide and CT)

Battery Level: 5.7
TideMaster S/N: 3
Station ID: 01
Site info: Valeport test site!
Mode: B1
Pressure units: m
Radar:
Min limit: 0.500
Max Limit: 20.000
Datum: 2.000
Pre amble: 4
Water Temperature units: Deg C
Water Conductivity units: mS
Timestamp [TAB] Depth [TAB] Depth SD [TAB] WaterTemp [TAB] WaterCond [TAB] Batt Status

Data
4.5. Real Time Data - NMEA

Real Time data is broadcast in NMEA format only.
A NMEA style output is the standard data format and provides the most detailed information from
the instrument.
4.5.1. $PVTMA and $PVRS1 - Tide Data

$PVTMA - Pressure data
$PVTMA,ID,ccyymmdd,hhmmss,tt.ttt,h.hhh,U,vv.v,vv.v,nnnn,,,*hhCL
example: $PVTMA,01,20180528,171600,01.724,0.004,0,06.3,12.4,1024,,,*35
// Station ID XX (integer)
// Date CCYYMMDD
// Time hhmmss
// Tide Height tt.ttt
// Tide height stdev h.hhh
// Tide height units U
d = DBar
m = Metres
f = Feet (multiplier = 0.30480370641307)
// Internal Battery Volts
voltage
// External Battery Volts
voltage
// Data Status nnnn
Pressure DBar (native units)
reserved 1
reserved 2
// *hh checksum
// CL <cr><lf> end of string

$PVRS1 - Radar level data

$PVRS1,ID,CCYYMMDD,hhmmss,tt.ttt,l.lll,h.hhh,nnnn,U,,*hhCL
example: $PVRS1,01,20180105,061800,5.011,0.694,0.017,000,*64
// Date CCYYMMDD
// Time hhmmss
// Range tt.ttt
// Level l.lll
// Standard Deviation h.hhh
// Data Status nnnn
// Units U
m = Metres
f = Feet (multiplier = 0.30480370641307)
// *hh checksum

Data
4.5.2. $PVTM1 - Meteorological Data

$PVTM1 = Meteorological Data, same format for Windsonic or MetPak II
$PVTM1,ID,CCYYMMDD,hhmmss,sss.ss,kk.kk,mmm.mm,U,ddd.d,nn.nn,aaaa.a,A,ttt.t,T,ppp.p,hhh.h*hh
CL (85 chars)
example: $PVTM1,01,20180301,011000,001.70,00.18,001.96,1,357.2,07.15,1032.5,0,011.2,0,010.4,094.4,*15
// Date CCYYMMDD
// Time hhmmss
// wind speed sss.ss
// wind speed stdev stdev kk.kk
// max gust mmm.mm
// wind speed units U
0 = kts (multiplier = 0.51486061341309)
1 = metres per second (multiplier = 1)
2 = miles per hour (multiplier = 0.44704)
// wind direction ddd.d
// wind direction stdev stdev nn.nn
// air pressure aaaa.a
// air pressure units A
0 = mbar (multiplier = )
1 = hpa (multiplier = )
2 = inHg (multiplier = )
3 = mmHg (multiplier = )
// air temperature ttt.t
// temperature units T
0 Deg C
1 Deg F
// dew point ppp.p
// humidity hhh.h
// *hh checksum

4.5.3. $PVTM2 - Water Temperature and Conductivity Data

$PVTM2,ID,CCYYMMDD,hhmmss,tt.ttt,U,CC.CCC,mS,*hhCL
example: $PVTM2,01,20180301,022000,-9.900,0,-9.900,mS,*20
// Date CCYYMMDD
// Time hhmmss
// Water Temperature tt.ttt
// Water Temperature Units U
0 = Degs C
1 = Degs F (multiplier=0.555555556; offset=-17.777778
// Water Conductivity CC.CCC
// Water Conductivity units mS always (mS = ms/cm)
//Checksum *hh

SATEL - M3 - TR1
5. SATEL - M3 - TR1
Introduction
SATELLINE-M3-TR1 transceiver module is a compact, flexible and lightweight solution with low power
consumption. The module is specifically designed for small mechanics.
It is an excellent choice for applications requiring long-range distances.
Lightweight solution for long-range connections

The module has a wide (90 MHz / 70 MHz) tuning range and the operation frequency can be
selected within the ranges 330…420 MHz and 403…473 MHz. The channel spacing 12.5, 20 and 25
kHz are software-selectable. The output power of up to 1W enables long connection distances.
The key features include:

· 330-420 / 403-473 MHz frequency range – 90 / 70 MHz wide tuning range enables two radio
modems in the stock and all the channels available
· User selectable channel spacing 12.5 / 20 / 25 kHz
· Compatible with the widely used SATELLINE-EASy radio modem family
· Compatible also with Pacific Crest-4FSK/GMSK/FST or TRIMTALK450s protocols
· Half duplex radio data transfer
· Over-the-air data rate:
- 9600 bps @ 12.5 kHz channel spacing
- 9600 bps @ 20 kHz channel spacing
- 19200 bps @ 25 kHz channel spacing
· Small current consumption, sleep modes
· Power level of the transmitter 100 mW…1 W
· RS-232 / RS422 / LVTTL / TTL serial interface at 300…38400 bps data rates
· Routing/repeater functions
· Error correction (FEC)
· External command language (SL commands)
· OEM versions available

5.1. Specification
RADIO RECEIVER TRANSMITTER
Frequency Range 1
330…420 Note / 403...473 MHz (Tuning range 90 / 70 MHz)
Channel Spacing 12.5 kHz / 20 kHz / 25 kHz programmable
Communication Mode Half-Duplex
Frequency Stability <1 kHz
Modulation 4-FSK, GMSK
Radio Compatibility SATELLINE-3AS, Pacific Crest FST/4-FSK/GMSK, TRIMTALK450s
Spurious Radiation < 2 nW EN 300 113 and CFR47 part90
Sensitivity -114 dBm @12.5 kHz
2&3
-111 dBm @25 kHz Note
Co-channel Rejection 2
>-12 dB Note
Adjacent Channel > 47 dB @12.5 kHz
Selectivity 2
> 52 dB @ 25 kHz Note
Inter-modulation 2
> 60 dB Note
Attenuation
Blocking 2
> 86 dB Note
Spurious Rejection 2
> 60 dB Note
Spurious Emission < -100 dBm <-80 dBm on 3rd harmonic
@1215–1240 MHz
Type of Emission F1D
Carrier power 100, 200, 500, 1000 mW
Adjacent Channel Power EN 300 113 and CRF47 part90
Carrier power stability < ±1.5 dB
DATA MODEM
Electrical Interface Port 1:RS-232 / Port 2: LVTTL, TTL or RS-232/422 (depends on the
assembly)
Interface Connector D-15 (female)
Data speed of Serial 300 – 38400 bps
interface
Data speed of Radio 19200 bps (25 kHz channel) / 9600 bps (12.5 or 20 kHz channel)
Interface

SATEL - M3 - TR1
GENERAL
RADIO RECEIVER TRANSMITTER
Power Consumption <1.2 W (Receive), <3.0 W (Transmit @ 0.5 W), <7.0 W (Transmit @ 1 W),
0.12 W (Sleep mode), 10 mW (DTR Power save)
Temperature Ranges -25 °C ... +55 °C Complies with standards
-30 °C ... +65 °C Functional
-40 °C ... +75 °C Absolute min./max.
-40 °C ... +85 °C Storage
Antenna Connector TNC female 50 ohm
Construction Aluminium housing or without housing
Size L x W x T 129 x 63.5 x 23 mm (+/- 1 mm) or 89 x 49 x 9 mm
Weight 250 g or 50 g
1
Note 330.000 – 389.950 MHz, 390.050 – 420.000 MHz
2
Note Values apply with FEC ON @ BER<10E-3
3
Note Due to radio electronic design, the receiver is about 6 – 15 dB less sensitive on the following
frequencies: 403.000, 416.000, 429.000, 442.000, 455.000, 468.000, 409.5875 and 469.200 MHz.

5.1.1. SATEL Radio Schematic
5.2. Safety Note

· Warranty will be void, if the product is used in any way that is in contradiction with the instructions
given in the operator's manual, or if the radio modem housing has been opened or tampered with.
· The radio modem is only to be operated at frequencies allocated by local authorities, and without
exceeding the given maximum allowed output power ratings. SATEL and its distributors are not
responsible, if any products manufactured by it are used in unlawful ways.
· The devices mentioned in this manual are to be used only according to the instructions described
in this manual. Faultless and safe operation of the devices can be guaranteed only if the transport,
storage, operation and handling of the devices is appropriate. This also applies to the maintenance
of the products.
· To prevent damage both the radio modem and any terminal devices must always be switched OFF
before connecting or disconnecting the serial connection cable. It should be ascertained that

SATEL - M3 - TR1
different devices used have the same ground potential. Before connecting any power cables the
output voltage of the power supply should be checked.
· Any radio link can susceptible to external interference and signal degradation by its nature.
Because of that, the effects of possible interference mechanism and the sufficient back-up schemes
must be taken into account in the system design of the critical applications.
5.2.1. Restrictions on Use

SATELLINE-M3-TR1 radio modem modules have been designed to operate on frequency ranges, the
exact use of which differs from one region and/or country to another. The user of a radio modem
must take care that the device is not operated without the permission of the local authorities on
frequencies other than those specifically reserved and intended for use without a specific permit.
SATELLINE-M3-TR1 is allowed to be used in the following countries, either on licence free channels
or on channels where the operation requires a licence. More detailed information is available at the
local frequency management authority.
Countries: AT, AU, BE, BG, CA, CH, CY, CZ, DE, DK, EE, ES, FI, FR, GB, GR, HR, HU, IE, IS, IL, IN, IT, KZ,
LT, LU, LV, MX, MT, NL, NO, OM, PL, PT, RU, RO, SE, SG, SI, SK, TR, UA, US, VN and ZA.
WARNING! Users of SATELLINE-M3-TR1 radio modem modules in North America should be

aware, that due to the allocation of the frequency band 406.0 – 406.1 MHz for government use
only, the use of radio modem on this frequency band without a proper permit is strictly
forbidden.
WARNING! In order to comply with FCC and IC RF exposure compliance requirements, maximum
antenna gain is 14 dBi and separation distance of at least 1 meter must be maintained between
the antenna of this device and all persons. The device must not be co-located or operating in
conjunction with any other antenna or transmitter.
Note on label requirements: SATELLINE-M3-TR1 is intended to be integrated into a host device or an

enclosure. Therefore the product related FCC ID and IC ID must be visible in the host device chassis.
SATELLINE-M3-TR1 869 radio modem module has been designed to operate on 869.4125 – 869.6375
MHz, the exact use of which differs from one region and/or country to another. The user of a radio
modem must take care that the device is not operated without the permission of the local authorities
on frequencies other than those specifically reserved and intended for use without a specific permit.
SATELLINE-M3-TR1 869 is allowed to be used in the following countries, either on licence free
channels or on channels where the operation requires a licence. More detailed information is
available at the local frequency management authority.
Countries: AT, BE, BG, CH, CY, CZ, DE, DK, EE, ES, FI, FR, GB, GR, HR, HU, IE, IS, IT, LT, LU, LV, MT, NL,
NO, PL, PT, RO, SE, SI, SK and TR.

5.3. Approvals
COMPLIANT WITH THE INTERNATIONAL STANDARDS
RF-requirements EN 300 113-2 / FCC CFR47 section 90
EMC-requirements EN 301 489-1 & -5 (8 kV contact, 15 kV air discharge)
Safety Standard EN 60950-1
Immunity EN 61000-4-3 (2006) (10V/m)
Hereby, SATEL Oy declares that radio modem modules are in compliance with the essential
requirements (radio performance, electromagnetic compatibility and electrical safety) and other
relevant provisions of Directive 2014/53/EU. Therefore the equipment is labelled with the following
CE-markings.

Victron Energy Solar Charge Controller
6. Victron Energy Solar Charge Controller

Please refer to the specific Victron Energy manual for the model installed in your TideStation.
General Description
Ultra fast MPPT tracking
Especially in case of a clouded sky, when light intensity is changing continuously, a fast MPPT
algorithm will improve energy harvest by up to 30% compared to PWM charge controllers and by up
to 10% compared to slower MPPT controllers.
Load Output
Deep discharge of the battery can be prevented by connecting all loads to the load output. The load
output will disconnect the load when the battery has been discharged to a pre-set voltage.
Alternatively, an intelligent battery management algorithm can be chosen: see Battery Life.
The load output is short circuit proof.
Some loads (especially inverters) can best be connected directly to the battery, and the inverter
remote control connected to the load output. A special interface cable may be needed.
Internal Temperature Sensor
Compensates absorption and float charge voltages for temperature.
Automatic Battery Voltage Recognition
The controller will automatically adjust itself to a 12V or a 24V system one time only.
If a different system voltage is required at a later stage, it must be changed manually.
Three Step Charging
The controller is configured for a three step charging process:
Bulk | Absorption | Float. See below for details.
Bulk
During this stage the controller delivers as much charge current as possible to rapidly recharge the
batteries.
Absorption
When the battery voltage reaches the absorption voltage setting, the controller switches to constant
voltage mode.
When only shallow discharges occur the absorption time is kept short in order to prevent
overcharging of the battery. After a deep discharge the absorption time is automatically increased to
make sure that the battery is completely recharged.
Additionally, the absorption period is also ended when the charge current decreases to less than 1A.
Float
During this stage, float voltage is applied to the battery to maintain a fully charged state. When the
battery voltage drops below float voltage during at least 1 minute a new charge cycle will be
triggered.

6.1. Important Safety Instructions

SAVE THESE INSTRUCTIONS - This manual contains important instructions that shall be
followed during installation and maintenance.
Danger of explosion from sparking
Danger of electric shock
· It is advised to read this manual carefully before the product is installed and put into use.
· This product is designed and tested in accordance with international standards. The equipment
should be used for the designated application only.
· Install the product in a heatproof environment. Ensure therefore that there are no chemicals,
plastic parts, curtains or other textiles, etc. in the immediate vicinity of the equipment.
· The product is not allowed to be mounted in a user accessible area.
· Ensure that the equipment is used under the correct operating conditions.
· Never use the product at sites where gas or dust explosions could occur.
· Ensure that there is always sufficient free space around the product for ventilation.
· Refer to the specifications provided by the manufacturer of the battery to ensure that the battery is
suitable for use with this product. The battery manufacturer's safety instructions should always be
observed.
· Protect the solar modules from incident light during installation, e.g. cover them.
· Never touch uninsulated cable ends.
· Use only insulated tools.
· Connections must always be made in the following sequence
- First: connect the cables to the load, but ensure that all loads are switched off.
- Second: connect the battery (this will allow the controller to recognize system voltage).
- Third: connect the solar array.
· The installer of the product must provide a means for cable strain relief to prevent the transmission
of stress to the connections.
6.2. Installation
WARNING: DC (PV) INPUT IS NOT ISOLATED FROM BATTERY CIRCUIT
CAUTION: FOR PROPER TEMPERATURE COMPENSATION THE AMBIENT CONDITION FOR
CHARGER AND BATTERY MUST BE WITHIN 5°C.
General
· Mount vertically on a non-flammable substrate, with the power terminals facing downwards.
· Mount close to the battery.
· Improper internal temperature compensation (e.g. ambient condition battery and charger not
within 5°C) can lead to reduced battery lifetime.
· In Canada battery installation must be done in accordance with the storage battery rules of the
Canadian Electrical Code, Part I.
· The battery and PV connections must be guarded against inadvertent contact.

Grounding
· Battery grounding: the charger can be installed in a positive- or negative-grounded system.
· Chassis grounding: A separate earth path for the chassis ground is permitted because it is isolated
from the positive and negative terminal.
· The USA National Electrical Code (NEC) requires the use of an external ground fault
· protection device (GFPD). These MPPT chargers do not have internal ground fault protection. The
system electrical negative should be bonded through a GFPD to earth ground at one (and only
one) location.
· The charger must not be connected with grounded PV arrays.
WARNING: WHEN A GROUND FAULT IS INDICATED, BATTERY TERMINALS AND CONNECTED

CIRCUITS MAY BE UNGROUNDED AND HAZARDOUS.
PV Configuration
· Provide means to disconnect all current-carrying conductors of a photovoltaic power source from
all other conductors in a building or other structure.
· A switch, circuit breaker, or other device, either ac or dc, shall not be installed in a grounded
conductor if operation of that switch, circuit breaker, or other device leaves the grounded
conductor in an ungrounded state while the system remains energised.
· The controller will operate only if the PV voltage exceeds battery voltage (Vbat).
· PV voltage must exceed Vbat + 5V for the controller to start. Thereafter minimum PV voltage is
Vbat + 1V.
· Maximum open circuit PV voltage: 75V respectively 100V
at low temperature the open circuit voltage of a 108 cell array may exceed 75V and and the open
circuit voltage of a 144 cell solar array may exceed 100V, depending on local conditions and cell
specifications. In that case the number of cells in series
must be reduced.
Cable Connection Sequence

First: connect the cables to the load, but ensure that all loads are switched off.
Second: connect the battery (this will allow the controller to recognize system voltage).
Third: connect the solar array (when connected with reverse polarity, the controller will
heat up but will not charge the the battery).
The system is now ready for use.
The Load Output

A jumper can be used to to configure the load output as follows:
· No jumper: Battery Life algorithm (see 1.4)
· Jumper between pin 1 and pin 2: conventional
Low voltage load disconnect: 11,1V or 22,2V
Automatic load reconnect: 13,1V or 26,2V
· Jumper between pin 2 and pin 3: conventional
Low voltage load disconnect: 11,8V or 23,6V
Automatic load reconnect: 14V or 28V

LEDs
Green LED: indicates which load output control algorithm has been chosen.
On: one of the two conventional load output control algorithms (see Fig 2)
Blinking: BatteryLife load output control algorithm (see Fig 2)
Yellow LED: signals charge sequence

Off: no power from PV array (or PV array connected with reverse polarity)
Blinking fast: bulk charge (battery in partially charged state)
Blinking slow: absorption charge (battery charged to 80% or more)
On: float charge (battery fully charged)
Battery Charging Information

The charge controller starts a new charge cycle every morning, when the sun starts shining.
Default setting:
The maximum duration of the absorption period is determined by the battery voltage measured just
before the solar charger starts up in the morning:
Battery voltage Vb (@start- Maximum absorption time

up)
Vb < 23.8V 6h
23.8V < Vb < 24.4V 4h
24.4V < Vb < 25.2V 2h
Vb > 25.2V 1h
(divide voltages by 2 for a 12V system)
If the absorption period is interrupted due to a cloud or due to a power hungry load, the absorption
process will resume when absorption voltage is reached again later on the day, until the absorption
period has been completed.
The absorption period also ends when the output current of the solar charger drops to less than
1Amp, not because of low solar array output but because the battery is fully charged (tail current cut
off).
This algorithm prevents over charge of the battery due to daily absorption charging when the system
operates without load or with a small load.
User defined algorithm:

The default settings can be modified via VE.Direct.
Automatic Equalization
Automatic equalization is default set to ‘OFF’. With the Victron Connect app this setting can be
configured with a number between 1 (every day) and 250 (once every 250 days). When automatic
equalization is active, the absorption charge will be followed by a voltage limited constant current
period. The current is limited to 8% of the bulk current for the factory default battery type, and to
25% of the bulk current for a user defined battery type. The bulk current is the rated charger current
unless a lower maximum current setting
has been chosen.

When using the factory default battery type, automatic equalization ends when the voltage limit
16.2V / 32.4V has been reached, or after t = (absorption time)/8, whichever comes first. For the user
defined battery type automatic equalization ends after t = (absorption time)/2. When automatic
equalisation is not completely finished within one day, it will not resume the next day, the next
equalisation session will take place as determined by the day interval.
6.3. Trouble Shooting

Problem Possible Cause Solution
Reversed PV connection Connect PV correctly
Charger does not function
No fuse inserted Insert 20A fuse
Reversed battery connection 1. Connect battery correctly
Blown fuse
2. Replace Fuse
A bad battery connection Check battery connection
Cable losses too high Use cables with larger cross section
Large ambient temperature Make sure that ambient conditions
difference between charger and are equal for charger and battery
The battery is battery (Tambient_chrg >
not fully charged Tambient_batt)
Only for a 24V system: wrong Set controller manually to the
system voltage chosen (12V required system voltage (see
instead of 24V) by the charge section 1.8)
controller
A battery cell is defect Replace battery
Large ambient temperature Make sure that ambient conditions
The battery is being
difference between charger and are equal for charger and battery
overcharged
battery (Tambient_chrg <
Tambient_batt)
Maximum current limit Make sure that the output current
exceeded does not exceed 15A
DC load in combination with Disconnect DC load during start-up
capacitive load (e.g. of the capacitive load Disconnect
Load output does not become
inverter) applied AC load from the inverter, or
active
connect inverter as explained in
section 3.6
Short-circuit Check for short-circuit in the load
connection

6.4. Specification
BlueSolar charge controller MPPT 75/10 MPPT 75/15 MPPT 100/15
Battery voltage 12/24V Auto Select
Maximum battery current 10A 15A 15A
Nominal PV power, 12V 1a,b) 145W 220W 220W
Nominal PV power, 24V 1a,b) 290W 440W 440W
Max. PV short circuit current 2) 13A 15A 15A
Automatic load disconnect Yes, maximum load 15A
Maximum PV open circuit voltage 75V
Peak efficiency 98%
Self consumption 12V: 20 mA 24V: 10 mA
Charge voltage 'absorption' 14,4V / 28,8V (adjustable)
Charge voltage 'equalization' 3) 16,2V / 32,4V (adjustable)
Charge voltage 'float' 13,8V / 27,6V (adjustable)
Charge algorithm multi-stage adaptive or user defined algrithm
Temperature compensation 16mV / °C resp. -32mV / °C
Continuous load current 15A
Low voltage load disconnect 11,1V / 22,2V or 11,8V / 23,6V
or BatteryLife algorithm
Low voltage load reconnect 13,1V / 26,2V or 14V / 28V
or BatteryLife algorithm
Protection Battery reverse polarity (fuse)
Output Short Circuit / Over Temperature
Operating temperature -30 to +60°C (full rated output up to 40°C)
Humidity 100%, non-condensing
Maximum altitude 5000m (full rated output up to 2000m)
Environmental condition Indoor type 1, unconditioned
Pollution degree PD3
Data communication port VE.Direct
see the data communication white paper on the victron energy
website
1a) If more PV power is connected, the controller will limit input power.
1b) The PV voltage must exceed Vbat + 5V for the controller to start.
Thereafter the minimum PV voltage is Vbat + 1V.
2) A higher short circuit current may damage the controller in case of reverse polarity connection of
the PV array.
3) Default setting: OFF

6.4.1. Enclosure
BlueSolar charge
MPPT 75/10 MPPT 75/15 MPPT 100/15
controller
Enclosure
Colour Blue (RAL 5012)
Power terminals 6mm² / AWG10
Protection category IP43 (electronic components) IP22 (connection area)
Weight 0.5kg 0.6kg
Dimensions (h x w x d) 100 x 113 x 40mm 100 x 113 x 50 mm
6.4.2. Standards
Standards
Safety EN/IEC 62109-1 / UL 1741 / CSA C22.2 NO.107.1-16

6.5. Configuration
Figure 1a: configuration pins of the VE.Direct communication

port, 75V models
Figure 1b: pin numbering of the VE.Direct

communication port

6.5.1. Battery Management Options

No bridge: BatteryLife algorithm
Bridge between pin 1 and 2:

Low voltage disconnect: 11.1V or 22.2V
Automatic load reconnect: 13.1V or 26.2V
Standard setting for TideStation. Contact Valeport

before making any change to this setting.
Bridge between pin 2 and 3:

Low voltage disconnect: 11.8V or 23.6V
Automatic load reconnect: 14.0V or 28.0V
6.5.2. Power Connections

7. Scannex ip.Buffer
Please refer to the specific Scannex manual for the model installed in your TideStation for more
detailed operational instructions.
Introduction
The Range
The ip.buffer is designed to collect and store information from such devices as telephone PBXs – for
CDR/SMDR collection, for alarm and traffic management, and to allow pass-through access for
moves and changes.
The product range includes two main devices:
· ip-4 = 128Mbyte memory with 4 serial ports
· ip-1 = 32Mbyte memory with 1 serial port
The ip-4 device includes internal temperature monitoring, built in global or GPRS modem, plus the
SEbus expansion connector. They are both built inside a metal box that can be rack mounted in a 1U
high bay.
The ip-1 device has an optional global PSTN or GPRS modem and is housed in a plastic casing with
facilities for wall mounting, tie-wrapping, and DIN rail mounting.
Both devices allow battery backup using 3 standard AA NiMH batteries. With fully charged cells the
unit can continue to operate for approximately 2 hours.
Features
All devices have proprietary Scannex features and advanced facilities:
· Collection
- Auto pin detection on the serial ports1
- Auto baud rate and protocol detection on the serial ports
- Collection from serial and TCP/IP enabled devices2
- Collection from devices that perform FTP push
- Collection of UDP data including syslog information, SNMP Traps (with trap decoding and
SNMP get queries on connected devices), and RADIUS Accounting
- Collection from a web server running Scannex C# or PHP scripts.
- Support for ASCII, Binary and iSDX data sources
- Automatic partitioning of NAND flash memory with optional settings for limiting memory sizes
of each channel
· Various delivery options including:
- HTTP/HTTPS post to web Cloud Server
- FTP/SFTP push
- FTP server
- Email/SMTP push
- TCP/IP push o TCP/IP server
- COM port serial

Scannex ip.Buffer
· LAN and management features

- Fully web-based setup and status information
- “Reflective Routing” on the LAN to allow easy access from different subnets3
- Email, HTTP POST, and SNMP alert mechanisms to enable a pro-active system
- Extremely powerful Lua4 scripting engine
- SNTP (Simple Network Time Protocol) time synchronisation with daylight saving option
- Settings can be quickly replicated across multiple ip.buffers for bulk installations
- All changes to the settings occur immediately – no need for reboot5
- Fully fail-safe firmware upgrades. The power can fail at any point in the upgrade process and the
ip.buffer will recover with the old version (or the new version if successfully uploaded).
- Simple SNMP v1/v2c agent to provide inventory information to SNMP clients
- Centralised updates via standard web-server (See section 8.2.16)
- Supports Proxy servers running HTTP, SOCKS 5 and SOCKS 4a protocols.
· Security features
- Option to authenticate to one or two RADIUS servers
- https (SSL) access for web pages (optional)
- SSL/TLS link encryption for HTTP post, FTP, email, and TCP connections (optional)
- SFTP/SSH encryption for SFTP push (See section 11.4)
1
The detection is performed using voltage sensing, so the ip.buffer can detect whether the data
source is DCE or DTE wired even with no data
2
Each ip.buffer can collect data from as many TCP/IP devices as there are serial ports. Each channel
can be assigned to either the serial port or a TCP/IP or UDP/IP collection.
3
In practice it means you do not have to have a gateway address, or the correct gateway,
programmed in the ip.buffer when connecting into it for web services and the like.
4
See www.lua.org However, several extensions have been applied to the Lua base.
5
Even Lua script changes can occur while the ip.buffer is still running
Only an authorised repair facility is allowed to service the modem. Please contact your supplier
or Scannex for details of how to have repairs made. Unauthorised repairs could void authority to
use the ip.buffer and be dangerous

7.1. Specification
Serial Port(s) RS232/V24, 9-pin plug. Auto DCE/DTE selection (rx pin 2 or 3) Output pin
resolves according to input detection (or manually set).
Baud: 300-115200 baud
Data: 7-bit odd/even, 8-bit odd/even/none
Full autobauding and parity detection within this range.
Network 100base-TX/10base-T, RJ-45 unshielded, full/half duplex, auto MDIX (auto
cross-over).
Memory 32Mb/64Mb/128Mb flash. 10 year data hold up without battery (4Mb
used for firmware)
Power consumption (including PSU): 3W / 10BTU/h
Physical Temperature: 5-50°C (40-122°F)
Humidity: 20-80% R.H. (non condensing)
ip.1-32(m) Dimensions: 160 x 120 x 45mm / 6.3” x 4.7” x 1.8” (LxWxH)
Weight: 0.25kg / 0.55lb
ip.4-128.m Dimensions: 250 x 160 x 42mm / 9.8” x 6.3” x 1.7” (LxWxH)
Weight: 1kg / 2.20lb
GPRS Modem (only applicable to ip.buffers containing a GRPS modem)
SIM 1.8/3V Mini-Subscriber Identity Module (SIM) compatible. Antenna
Interface Female SMA.
Frequency bands EGSM 900, DCS 1800, and PCS 1900, GSM 850 capability.
Antenna gain 2 dBi in mobile applications and 7dBi in Fixed.
GSM/GPRS features supported:
Provides for all GSM/GPRS authentication, encryption, and
frequency hopping algorithms.
GPRS coding schemes:
CS1-CS4 supported. Multi-Slot Class 10 (4rx/2tx, maximum

Scannex ip.Buffer
7.2. GPRS Operation with a Cellular/Mobile Network

The ip.buffer is fitted with a GPRS modem allowing delivery of data and remote access over the
cellular/mobile network.
An appropriate SIM card for the country of installation (SIM 1.8/3V Mini-Subscriber Identity Module (SIM)) will
be required and only an approved antenna suitable GPRS operation should be used.
Operational Frequencies
800/850/900/1900/2100MHz@UMTS
850/900/1800/1900MHz@GSM
Output Power
Class 3 (24dBm+1/-3dB) for UMTS bands
Class E2 (27dBm±3dB) for EDGE 850/900
Class E2 (26dBm+3/-4dB) for EDGE 1800/1900
Class 4 (33dBm±2dB) for GSM 850/900
Class 1 (30dBm±2dB) for GSM 1800/190
7.2.1. GPRS Safety Precautions

Be sure the use of this product is allowed in the country and in the environment required. The use of
this product may be dangerous and has to be avoided in the following areas:
Where it can interfere with other electronic devices in environments such as hospitals, airports,
aircraft, etc.
Where there is risk of explosion such as gasoline stations, oil refineries, etc
It is responsibility of the user to enforce the country regulation and the specific environment
regulation.
· Avoid contact with the ip.buffer or ancillary equipment during an electrical storm; there is a risk of
electrical shock.
· Do not use the equipment in the vicinity of a gas leak.
· Avoid contact with liquids and do not use if the unit is suspected to be damp.
· There are no user serviceable parts inside.
· for operation within the TideStation only.
· Power surges on power lines, such as those caused by lightning strikes, can destroy or damage the
ip.buffer. Therefore, we recommend that the DC Power supply and all interfaces are connected via
surge protectors.
7.2.2. GPRS Radiation Exposure Statements

Failure to meet these requirements may mean the maximum permissible exposure (MPE) limit is
exceeded!
· The device should be used in such a way that a separation distance of at least 20 cm (8 inches) is
maintained between the transmitter's antenna and any nearby persons.
· The antenna gain must not exceed 3 dBi relative to an isotropic radiator
see approved antennae list here

7.3. Fitting Batteries

The ip.buffer can run from 3 x standard AA-size Ni-MH batteries when the mains power fails
(supplied without batteries). With fully charged batteries the ip.buffer should run for at least 2 hours
(although this run time can be limited using the configuration options).
Batteries are not supplied
7.3.1. Battery Precautions

· Use only AA sized rechargeable Ni-MH batteries capacity of at least 2000mAH.
· Batteries should all be of the same capacity, manufacturer, and type.

· RISK OF EXPLOSION IF BATTERIES OF INCORRECT TYPE ARE FITTED.
· Never use non-rechargeable batteries.
· Do not burn or puncture the batteries. The cells may explode.

· Check with local requirements for possible special disposal instructions.
· When replacing batteries all batteries should be replaced at the same time.
· Remove the batteries from the product if the product will not be used for some time (several
months or more).
· Check with local requirements for shipping restrictions before shipping with batteries fitted. Some
authorities strongly recommend shipping without batteries fitted!

Scannex ip.Buffer
7.4. Front Panel LED

The LED on the front panel shows the following information:
When the ip.buffer boots up, the Modem LED will flash if there is a modem present. If no modem is
installed, the Modem LED will not light (except for the regular 8 second flash)
Off Source not connected

Channel 1..4 On Source Connected
Flashing Data Arriving
Off No Ethernet Connection
L: LAN On Ethernet Connected
Flashing Ethernet Activity
Off Modem Off-Line
Slow Flash Answering or Dialling
M: Modem
Fast Flashing Negotiating PPP1
On Modem On-Line
S: Status Blinks every second to indicate the ip.buffer is functioning normally
E: Error Blinks when booting. Normally off
1
When the ip.buffer boots up, the Modem LED will flash if there is a modem present. If no modem is
installed, the Modem LED will not light (except for the regular 8 second flash)

7.5. Approvals
7.5.1. EMC
· CE Marks Class B (EN55022, EN55024)
· FCC CFR 47: Part 15 Class B
· CISPR 22 Class B (Emissions)
· CISPR 24 (Immunity)
· AS/NZS 3548 Class B (Australia & New Zealand accept CISPR 22)
· ICES 003 Class B (Canada accepts FCC)
European Union (EU) Statement

EMC, Safety, and R&TTE Directive Compliance
This is to certify that this product complies with the EU Directive 89/336/EEC and the amending
directive 93/68/EEC,relating to Electromagnetic Compatibility, by application of CISPR 22/European
Standard EN 55022 (Class B) requirements for Information Technology Equipment and EN55024 and
Council Directive 1999/5/EC on radio equipment and telecommunications terminal equipment and
the mutual recognition of their conformity.
7.5.2. Safety
· CE (EN60950)
· IEC 60950-1
· CB
7.5.3. Environmental
· RoHS Compliant
· WEEE Compliant
End of Life Disposal Instructions (WEEE)
For disposal instructions see http://www.scannex.co.uk/weee
7.5.4. GPRS Modem

(only applicable to ip.buffers containing a GPRS modem)
· GCF Type Approval
· PTCRB Type Approval
· FCC Certification (Part 24)
· RTTE
· CE (European Community Certification)
· IC (Industry Canada) Approval
· EMC Emissions: FCC Parts 15,22 & 24, Class B 3GPP TS 51010-1, Section 12.2 EN55022 Class B
· Cellular Listings: FCC, Industry Canada, PTCRB
· ICASA TA-2009/1363 (South Africa)
7.5.5. Export Control

· UK
- ECO Classification NLR (No License Required)
Scannex ip.Buffer
· US
- Hardware: ECCN 5A992 (NLR)
- Firmware: ECCN 5D992 (NLR)
- CCATS: G135797
7.5.6. FCC Rules Part 15 (Computing Devices)

Note: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part15 of the FCC rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following measures:
· Reorient or relocate the receiving antenna.
· Increase the separation between the equipment and receiver.
· Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
· Consult the dealer or an experienced radio/TV technician for help.
7.5.7. Industry Canada Information

Notice: The Industry Canada label identifies certified equipment. This certification means that the
equipment meets telecommunication network protective, operation and safety requirements as
prescribed in the appropriate Terminal Equipment Technical Requirements document(s).
The Department does not guarantee the equipment will operate to the user’s satisfaction. Before
installing this equipment, users should ensure that it is permissible to be connected to the facilities of
the local telecommunications company. The equipment must also be installed using an acceptable
method of connection. The customer should be aware that compliance with the above conditions
may not prevent degradation of service in some situations.
Repairs to certified equipment should be coordinated by a representative designated by the supplier.

Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may give
the telecommunications company cause to request the user to disconnect the equipment. Users
should ensure for their own protection that the electrical ground connections of the power utility,
telephone lines and internal metallic water pipe system, if present, are connected together. This
precaution may be particularly important in rural areas.
Caution: Users should not attempt to make such connections themselves, but should contact the
appropriate electric inspection authority, or electrician, as appropriate.
Notice: The Ringer Equivalence Number (REN) assigned to each terminal device provides an
indication of the maximum number of terminals allowed to be connected to a telephone interface.
The termination of an interface may consist of any combination of devices subject only to the
requirement that the sum of the Ringer Equivalence Numbers of all devices does not exceed 5.

7.6. Changing GPRS APN Settings

The following chapter describes the procedure to update the APN Settings of a Scannex N4X
ip.buffer.
The Scannex IP buffer can be configured if connected to LAN or direct to a computer.
Method A). Connection to network hub or switch.

Using Green M12 Cat5 cable, connect LAN port of Ip.buffer to the LAN.
Attach the TideMaster Cable and provide 12v/500mA source power, alternatively, switch TideStation
on, switch TideMaster on, enter the menu on TideMaster, select Output, select Telemetry Setup,
select radio on. This will enable power to the Scannex IP buffer from the integral charger unit. Ensure
that the internal battery is in a good state of charge.
Run SEDiscover application – this can be downloaded directly from the Scannex website here. This
utility will show all ip.buffers on the LAN. Select the relevant one to access the setup web page.
Method B). Using direct connection to Computer Ethernet port.

Using Green M12 Cat5 cable, connect LAN port of Ip.buffer to the computer.
1) Configure the Ethernet port of the computer to have a static IP Address – 192.168.0.100, subnet
255.255.255.0. The ip.buffer is pre-configured with 3 IP Addresses – one dynamic, two are fixed at
192.168.0.235 and 192.168.1.235 – for configuration.
On the computer:
a) go to “Control Panel\Network and Sharing Centre” – or search for sharing centre
b) Choose “Change Adapter Settings”
c) Right-Click the appropriate adapter, choose “Properties”

Scannex ip.Buffer
d) Scroll down and choose “Internet Protocol Version 4 (TCP/IPv4)” and click “Properties”
e) Choose “Use the following IP address”, and enter:
IP Address: 192.168.0.100
Subnet Mask: 255.255.255.0
Default Gateway: 192.168.0.1
The other settings have no effect.
f) Click “OK” and “OK” to return to the “Change Adapter Settings” screen.
The computer now has a static IP Address and can be connected directly to the ip.buffer. At the end
of this procedure it can be reverted to having a dynamic IP Address by repeating this process, but
choosing “Obtain an IP address automatically”

2) Connect the computer and the ip.buffer with the supplied green M12 to CAT5 cable – note longer
cables 5m can be ordered if required.
3) Cycle the power on the ip.buffer – disconnect, wait 30 seconds and reconnect the power cable.
The Ethernet port on the ip.buffer automatically powers down when it is not being used – it is,
however, switched on for 10 seconds on boot, and will remain on if it detects another Ethernet
device connected.

Scannex ip.Buffer
4) Browse to the ip.buffer with a standard web browser – the url is http://192.168.0.235
To the right of the “Modem” label is a box – this will probably be red with an error. When you hover
the mouse over the box, you will see a description of the error in the panel on the right hand side.
5) The status screen should appear – choose “Setup” from the menu.
6) You will be prompted for a user name/password – use “admin” and “secret” – which are case
sensitive.

7) Go to the GPRS settings – choose “Settings” and “Modem Out” – click the “show” button to the
right of “Modem Out”.
8) Enter the correct GPRS APN Settings – you will have to get these from the SIM Provider.

Scannex ip.Buffer
9) Click “Save Changes”
10) Go back to the “Status” screen, and after a minute or two – if the new settings are correct – the
GPRS should connect and start sending data.
When it has successfully connected, the modem “box” will turn green and say “Nailed Up (GPRS)”.
Any other errors will be displayed in the panel on the right when you hover the mouse over the
modem box.
11) Remove the CAT5 cable and re-fit the dust cover – this ensures the IP66 rating for the ip.buffer
enclosure.

7.7. Changing the SIM Card

Valeport do not supply TideStation systems with activated SIM cards as standard.
A SIM card can be fitted and activated under contract.
Should you require to fit or change the SIM card in your Scannex ip.buffer please follow the
procedure below.
The pictures below illustrate the Portable TideStation but the same is valid for the TideStation
Permanent.
1. Open the case and identify the TideMaster, Bluesolar charger and the battery switch. In the
picture below the system is powered - lights are visible on the Bluesolar charger and the battery
switch is set to ON.

Scannex ip.Buffer
2. Disconnect any external power source and switch the Battery switch to OFF: Ensure there are no
lights showing on the Bluesolar charger.
3. TideStation Portable - Remove the plate that holds the TideMaster, Bluesolar charger and battery
switch as shown above.
TideStation Permanent - Remove the plate that holds the Data Telemetry Unit (Radio) and
Bluesolar Charger as shown below:

The Scannex ip.buffer will be found underneath
4. Remove the 4 screws securing the ip.buffer lid. The SIM card can be found close to the battery
box. Make a note of the orientation of the SIM card before removing it.

Scannex ip.Buffer
5. Slide the SIM card and cage in the direction indicated to OPEN ®.
6. Flip up the cage and slide the SIM card out.
Replace the card; noting the orientation of the 'cut off corner'.
Push the cage back into position and slide as indicated to ¬ LOCK the SIM in place.
6. Replace the lid on the Scannex unit and reassemble the TideStation.

8. Cable Details
Wiring colours are correct at the time the manual was printed. However, it is advised that continuity
checks are performed prior to all terminations
8.1. Instrument Cables

8.1.1. 0741C26 - Tide: Pressure
END 2: 6Way Connector
CABLE END 1: UTS6JC10E6P
Pressure Sensor
WIRE COLOUR CONNECTOR PIN PRESSURE
RED A V+
WHITE B GND
YELLOW 6 Way Modified UTS - C SIG+
Druck PDCR1830
BLUE UTS6JC10E6P D SIG-
BLACK E N/C
SCREEN F Screen
8.1.2. 0745C11 - Tide: Radar (TideStation Permanent)

END 1: 0745518 PCB END 2: 0745518 PCB END 3: END 4:
Radar to Junction Box Out of Junction Box UTS6JC10E6P D-TYPE
(Terminal Block) (Terminal Block) TideMaster (For Setup)
WIRE COLOUR PIN PIN WIRE COLOUR PIN PIN FUNCTION
BLACK 1 1 BLACK POWER GND
RED 2 2 RED POWER IN
YELLOW 3 3 YELLOW RS232 OUT OF RADAR
BLUE 4 4 BLUE RS232 IN TO RADAR
GREEN 5 5 GREEN RS232 GND
SCREEN 6 6 SCREEN SCREEN
B POWER GND
A POWER IN
D RS232 OUT OF RADAR
C RS232 IN TO RADAR
E RS232 GND
F SCREEN
2 RS232 OUT OF RADAR
3 RS232 IN TO RADAR
1,5,6,8,9 RS232 GND
SHELL SCREEN
1. End 4 can be used by the operator to communicate directly to radar. Ensure that Pin 3 & 4 are
disconnected from J3 during this process to prevent any damage to the RS232 port.

Cable Details
8.1.3. 0741C17 - miniCT

END 1: END 2:
CABLE
MiniCT Sensor 6Way UTS -UTS6JC10E6P
WIRE WIRE
CONNECTOR PIN CONNECTOR PIN
TYPE COLOUR FUNCTION
RED 4 A V+ Supply to MiniCT
BLACK 6 B GND Supply to MiniCT
ORANGE 6 WAY MALE LINE 3 C RS232 Out to MiniCT
8Way 6 WAY UTS -
CONNECTOR
600 YELLOW 2 UTS6JC10E6P D RS232 In from MiniCT
MCIL6M
GREEN 1 E MiniCT 232 Gnd
SCREEN F Screen
8.1.4. WindSONIC
END 2: 6Way UTS -
CABLE END 1: GILL Sensor
UTS6JC10E6P
WIRE WIRE
CONNECTOR PIN CONNECTOR PIN
TYPE COLOUR FUNCTION
RED 3 A V+
BLACK 2 B GND
Windsonic 9 way
8Way ORANGE connector as 7 6 WAY UTS - C RS232 Out to Gill
600 YELLOW supplied with 5 UTS6JC10E6P D RS232 In from Gill
Windsonic Sensor
GREEN 1 E Gill 232 Gnd
SCREEN F Screen
8.1.5. 0741C27 - METPAK II

END 2:
END 1:
6Way UTS -
GILL MetPak II
UTS6JC10E6P
WIRE
COLOUR CONNECTOR PIN CONNECTOR PIN FUNCTION
RED 8 A V+ Supply to Gill
BLACK J5 7 B GND Supply to Gill
8 way Push fit Block
ORANGE 4 6 WAY UTS - C RS232 Out to Gill
YELLOW Pin 1 is nearest edge 3 UTS6JC10E6P D RS232 In from Gill
of board adjacent to
GREEN earth post. 2 E Gill 232 Gnd
SCREEN F Screen
Refer to METPAK manual for wiring information 1723-PS-0001 METPAK II User Manual issue 2.pdf.

8.2. Internal Loom Cables

8.2.1. 0741C26 - Internal Pressure Input to TideMaster
END 1: Enclosure END 2: TideMaster
CABLE: 8 Core 6Way Jam Nut Connector 6 Way Line Connector
screened Cable UTS710E6S UTS6JC10E6P FUNCTION
WIRE COLOUR CONNECTOR PIN CONNECTOR PIN PRESSURE
RED 6 Way Modified A 6 Way UTS - A V+
BLACK UTS710E6S B NCCM6 B GND
BLUE C UTS6JC10E6P C SIG+
YELLOW D D SIG-
E E N/C
SCREEN F F Screen
8.2.2. 0741C27 - Internal RADAR/Gill/CT Serial input to TideMaster

END 1: Enclosure END 2: TideMaster
6Way Jam Nut Connector 6 Way Line Connector
UTS710E6S UTS6JC10E6P FUNCTION
WIRE COLOUR CONNECTOR PIN CONNECTOR PIN RADAR
RED A A V+
BLACK B B GND
BLUE 6 Way C 6 Way UTS C RS232 Out to Radar
YELLOW UTS710E6S D UTS6JC10E6P D RS232 In from Radar
GREEN E E RS232 Gnd
SCREEN F F Screen
8.2.3. 0741C35 - Radio BNC to N Type RG58

END 1: Radio END 2: TideStation
Straight BNC Male Line N type Jack Female
connector Bulkhead connector
WIRE COLOUR CONNECTOR PIN CONNECTOR PIN FUNCTION
N type Bulkhead Signal
Core BNC Plug RG58 Centre Centre
Jack female IP67
Sheath Screen Screen Screen

Cable Details
8.2.4. 0741C53 - ip Buffer & Comms to Junction Box
END 1: 7 way Wurth

END 2: 7 way UTS female
Connector
CONNECTOR
PIN CONNECTOR PIN
WIRE COLOUR J1 FUNCTION
RED 1 7 Way A POWER_IN
UTS6JC10E7S
BLACK 2 B POWER_GND
BLUE 3 C RS232_OUT from
7 way Wurth TideMaster
YELLOW connector (J1) 4 D RS232_IN to TideMaster
GREEN 5 E RS232_GND
SCREEN E SCREEN
BROWN F COMMS_SEL
PURPLE 7 G RADIO_ON
8.2.5. 0741C54 - UHF\GSM Radio Comms to Junction Box

END 2: 7 WAY UTS
END 1: Junction Box
MALE
0741503
(Radio COMMS)
WIRE COLOUR CONNECTOR J3 PIN CONNECTOR PIN FUNCTION
BLUE 3 C RS232 OUT from Radio
YELLOW 4 D RS232 IN to Radio
GREEN 5 E RS 232 GND
RED 7 Way Wurth 1 7 WAY UTS A V+ OUT from Radio
J3 MALE Radio PWR input control
PURPLE 7 G
Radio On
BLACK 2 B 0V OUT
SCREEN 6 F SCREEN
8.2.6. 0741C55 - UHF\GSM Radio Power to Junction Box

END 2: 3 WAY UTS FEMALE
END 1: (POWER)
3 WAY UTS PWR V+ To
RED 1 A
FEMALE Telemetry Unit
3 way Wurth
PWR V- To
GREEN Connector (J4) 2 B
Telemetry Unit
SCREEN 3 C SCREEN

8.2.7. 0741C56 - DC input to Junction Box

END 1: END 2:
3 way UTS Jam Nut 3 Way Phoenix Plug
WIRE 3 way UTS
PIN Connector Pin
COLOUR Jam Nut FUNCTION
BROWN A J7 1 +ve input
BLUE B 3 Way 2 -ve input
Phoenix
6.6mm
screw
Crimp
Terminal
YELLOW/GR C
EEN
8.2.8. 0741C63 - Victron BlueSolar Solar Controller to Battery

END 3:
END 1: END 2: Panel Mounted
WIRE Solar Controller Toggle Switch Fuse Holder END 4: Battery
COLOUR PIN PIN PIN PIN FUNCTION
Solar battery +ve
RED Batt+ tbc (in)
output
Switched +v
tbc (out) Live
output
Battery +ve
B 1
Terminal
Battery -ve
BLACK Batt- through 2
Terminal

Cable Details
8.2.9. 0741C64 - Victron BlueSolar Solar Controller

to ip.Buffer
END 1: END 2:
Solar Controller In Line Fuse Holder
WIRE COLOUR CONNECTOR PIN Connector Pin
BROWN Screw Terminal load +'ve Fuse
(red) solder and Line In
BROWN adhesive heatshrink Fuse
Line Out
BLUE Screw Terminal load-'ve
(yellow)
END 3: ip.Buffer
Connector Pin FUNCTION
Souriau 7 Way Solar Load output +ve
Female A Fused system supply +v
UTS6JC10E7S B system supply -ve
8.2.10. 0741C65 - ip.Buffer/GSM Aerial Lead - Right Angle TNC to

TNC bulkhead
CABLE: RJ END 1: END 2: TideStation
Right Angle TNC Line connector TNC Bulkhead Connector
Core TNC Right Centre Centre Signal
TNC Bulkhead
Angle Plug
Sheath Screen Jack female IP67 Screen Screen
RG58
8.2.11. 0741C66 - Victron Solar Charge Controller to Junction Box

END 1: END 2: Junction Box
WIRE Solar Controller Board 0741503
COLOUR CONNECTOR PIN Connector Pin FUNCTION
+ve output from Solar
BROWN 6 (load+) 1
charger
-ve output from Solar
BLUE 5 (load-) J8 2
Charger
Screw Terminal Phoenix 4 way screw
+ve Input feed from Solar
BROWN 4 (solar+) connector 3
PV
-ve Input feed from Solar
BLUE 3 (solar-) 4
PV

8.2.12. 0741C70 - ip.Buffer Powerr Port to Junction Box Board

END 1: 7 Way Souriau UTS
Connector
ip.Buffer END 2: J6 3 way Wurth Plug
IP Buffer Power
RED A 1
Supply +ve
BLACK B 2 POWER GND
BLUE C
YELLOW UTS6JC10E7S D J6
GREEN E
BROWN n/c
PURPLE G
SCREEN F 3 SCREEN
8.2.13. 0741C71 - ip.Buffer Port 1 to Junction Box

END 1: 7 Way Souriau UTS
Connector END 2: J2 7 way Wurth Plug
Scannex IP Buffer
RED A J2 n/c
BLACK B n/c
RS232 OUT
BLUE C 3
from IP Buffer
RS232 IN
YELLOW D 4
UTS6JC10E7P to IP Buffer
GREEN E 2 RS232 GND
BROWN n/c
WHITE or IP BUFFER
G 7
ORANGE RADIO ON input
SCREEN F SCREEN
8.2.14. 0741C77 - External DC Input to 3 Way Female UTS Connector

END 3:
END 1: Pig Tail 3 way female UTS cable plug
WIRE COLOUR Connector PIN Connector Pin FUNCTION
BROWN +ve 3 way Female UTS A DC +ve
Free End
BLUE -ve connector plug B DC -ve

Cable Details
8.2.15. 0741C80 - ip.Buffer LAN Cable and Bulkhead

3rd party supply
End 1 Connector: M12 LAN plug
End 2 Connector: RJ45 into Bulkhead (BULGIN PX0833)
Screened Shielded twisted pairs
8.2.16. 0741C86 - DC Input from 3 Way Male UTS Jam Nut to Junction
Box
END 2 : Junction Box Power distribution
END 1 : 3 way Male Jam nut Power Board
Input 0741503
WIRE
CONNECTOR PIN COLOUR CONNECTOR: J12 PIN FUNCTION
UTS78E3P A CLEAR 3 Way Phoenix screw Terminal 1 Vin
UTS78E3P B BLACK 2 GND
UTS78E3P C SCREEN 3 SCREEN
8.2.17. 0741C87 - ip.Buffer Port 2 to Junction Box

END 1: 7 Way Souriau
UTS Connector END 2: J5 7 way Wurth
Scannex IP Buffer Plug
CONNECTOR
WIRE COLOUR Port 2 PIN CONNECTOR PIN FUNCTION
POWER OUTPUT CONTROL
RED UTS6JC10E7P A 7
(12v)
BLACK B 2 GND
RS232 OUT
BLUE C 3
from ip.Buffer
RS232 IN
YELLOW D J5 4
to ip.Buffer
GREEN E 5 RS232GND
BROWN n/c
WHITE or
G
ORANGE
SCREEN F 6 SCREEN

8.2.18. 0741C88 - DC Input from 3 Way UTS Jam Nut to Solar Charger
PV Input
END 2:
Free end (Solar charger
END 1: 3 way UTS Jam Nut screw terminal)
3 way UTS Jam
WIRE COLOUR Nut PIN Connector Pin FUNCTION
BROWN A screw terminal 1 +ve input
BLUE B (using crimp 2 -ve input
6.6mm Crimp
YELLOW/GREE blade
N connector)
8.2.19. 0741C89 - Victron Solar Controller to Satel Power input

END 2: END 3:
END 1: Solar Controller
In Line Fuse Holder Satel Power Input
FUNCTION
WIRE COLOUR CONNECT
Pin Connector Pin Connector Pin
OR
Screw Solar Load
BROWN load+ (red) Fuse Line In
Terminal solder and Souriau3 output +ve
adhesive Way Fused
Fuse Line
BROWN heat-shrink Female A system
Out
UTS6JC10E supply +v
Screw load- 3S system
BLUE B
Terminal (yellow) supply -ve
8.2.20. 0741C90 - Antenna BNC Wiring

END 2: TideStation
END 1: BNC Line connector
TNC Bulkhead connector
BNC Bulkhead Jack
Core BNC Plug RG58 Centre Centre Signal
female IP67
Sheath Screen Screen Screen

Cable Details
8.2.21. 0741C91 - Victron Solar Controller to Battery (switch)

END 1: Solar END 2: SPSW
Wire Controller Switch END 3: Fuse Holder END 4: Battery
Colour Connector Pin Connector Pin Connector Pin Connector Pin Function
Battery Solar
solder and
Batt tbc Crimp battery
RED adhesive
+'ve (in) Terminal +'ve
heat shrink
Ring output
solder and
Switched
Screw adhesive tbc
Live +'ve
Terminal heat-shrink (out)
output
(crimp blade
Battery
connector)
B 1 +'ve
Terminal
Battery
Batt
BLACK 2 -'ve
-'ve
Terminal
8.2.22. 0741C96 - TideMaster to Telemetry System Interface Lead

END 1: GSM/Scannex
END 2: TideMaster
ip.buffer
(7 Way Souriau UTS
(7 Way Souriau UTS
Connector)
Connector)
POWER IN to TideMaster
A A
RED from GSM unit
BLACK B B POWER GND
BLUE C D RS232 INTO TideMaster
7 way 7 way RS232 OUT FROM
D C
YELLOW size 10 Male size 10 Female TideMaster
GREEN E E RS232 GND
BROWN n/c F COMMS_SEL
WHITE G G RADIO ON
SCREEN F E SCREEN

TideStation Permanent Operating Manual 0741825b

Uploaded by

TideStation Permanent Operating Manual 0741825b

Uploaded by

TideStation Permanent

Document Ref: 0741825b (Permanent)

7.6. Changing GPRS

The following notices must be viewed with particular consideration.

· In order to comply with FCC and IC RF exposure compliance requirements,

· The TideStation Permanent is heavy. Special attention must be given to lifting

© 2018 Valeport Ltd Page 4

1.1. Graphical Symbols for Use on Equipment

4 IEC 60417-5032-1 (2002-10) Three-phase alternating current

5 IEC 60417-5017 (2006-08) Earth (ground) Terminal

6 IEC 60417-5019 (2006-08) Protective conductor terminal

7 IEC 60417-5020 (2002-10) Frame chassis terminal

9 IEC 60417-5007 (2009-02) On (power)

10 IEC 60417-5008 (2009-02) Off (power)

13 IEC 60417-5041 (2002-10) Caution hot surface

14 ISO 7000-0434B (2004-01) Caution

In position of a bi-stable push

17 ISO 361 Ionising Radiation

Page 5 © 2018 Valeport Ltd

2.2. TideStation Permanent Features

© 2018 Valeport Ltd Page 6

2.2.1.1. TideStation Enclosure - External Dimensions

Page 7 © 2018 Valeport Ltd

2.2.2. TideStation Schematics

TideStation Junction Box (0741503) Link settings:

© 2018 Valeport Ltd Page 8

2.2.2.1. Type - 0741020-ip4 Configuration

Page 9 © 2018 Valeport Ltd

2.2.2.2. Fully Specified with TideMaster GSM and Radio Telemetry

© 2018 Valeport Ltd Page 10

2.2.2.3. TideStation Permanent External Connectors

Page 11 © 2018 Valeport Ltd

2.2.2.4. Type - 0741020-0 Base Unit

Please contact Valeport for further information.

© 2018 Valeport Ltd Page 12

2.2.2.5. Type 0 External Connectors

Page 13 © 2018 Valeport Ltd

2.3. Sensor Specifications

Weather Sensor Options

METPak II TM Weather Station

To interface other sensor packages please contact Valeport for details

© 2018 Valeport Ltd Page 14

2.4. EU Declaration of Conformity - CE Marking

2.4.1.1. Approved Antennae

Page 15 © 2018 Valeport Ltd

RoHS Directive 2011/65/EU Standards

2.4.3. Export Control

© 2018 Valeport Ltd Page 16

Page 17 © 2018 Valeport Ltd

2.4.4.1. Approved Antenna

© 2018 Valeport Ltd Page 18

3.1.2. VRS20 Radar Level Sensor

3.1.3. Scannex IP-Buffer

Page 19 © 2018 Valeport Ltd

3.1.4. Satel UHF Radio

© 2018 Valeport Ltd Page 20

In the UK the maximum permitted transmit power is 500mW

Page 21 © 2018 Valeport Ltd

3.1.5. Powering the TideStation

There is a 5A fuse in TideStation Junction Box

There is a 20A fuse in Victron Solar Controller

3.1.5.1. Battery Installation

1. Disconnect any external supply

© 2018 Valeport Ltd Page 22

3.1.5.2. Lead Acid Battery Safety Statement

Gas release and Fire

Page 23 © 2018 Valeport Ltd

· Always handle batteries with care

Accident or Emergency Action and Treatment

© 2018 Valeport Ltd Page 24

Never smoke near a battery

Accident or Emergency Action and Treatment

Repairing of Damaged Batteries

Page 25 © 2018 Valeport Ltd

Disposal of Batteries & Associated Waste

REACH Regulation (EC) No 1907/2006