WPS 1310

QW-482 SUGGESTED FORMAT FOR WELDING PROCEDURE SPECIFICATIONS (WPS)
(See QW-200.1, Section IX, ASME Boiler and Pressure Vessel Code)
Company Name Small Vessel Works, Inc. By Bill Jones

Welding Procedure Specification No. WPS-1310 Date 05/05/2012 Supporting PQR No.(s) PQR-010
Revision No. 0 Date 05/05/2012
Welding Process(es) GMAW - Spray Type(s) Automatic, Machine, or Semi-Automatic

(Automatic, Manual, Machine, or Semi-Automatic)
JOINTS (QW-402) Details

All Groove and Fillet Weld Joints
Joint Design
Root Spacing 0 to 1/4 inch.
Backing: Yes With No Without
Backing Material (Type) Metal or Weldmetal, No Retainers

(Refer to both backing and retainers)
✔ Metal Nonfusing Metal

Nonmetallic Other
Sketches, Production Drawings, Weld Symbols, or Written Description
should show the general arrangement of the parts to be welded. Where
applicable, the details of weld groove may be specified.
[At the option of the manufacturer, sketches may be attached to illustrate

joint design, weld layers, and bead sequence (e.g., for notch toughness
procedures, for multiple process procedures, etc.)]
*BASE METALS (QW-403)

P-No. P-No. 1 Group No. to P-No. P-No. 1 Group No.
OR
Specification and type/grade or UNS Number
to Specification and type/grade or UNS Number
OR
Chem. Analysis and Mech. Prop.
to Chem. Analysis and Mech. Prop.
Thickness Range:
Base Metal: Groove 1/16 in. to 3/4 in. Fillet All Fillet Weld Sizes
Maximum Pass Thickness /2 inch (13 mm)
1 (Yes) ✔ (No)
Other QW-403.10 Not Applicable
*FILLER METALS (QW-404) 1 2

Spec. No. (SFA) SFA-5.18
AWS No. (Class) ER70S-6

F-No. 6
F-No.
A-No. A-No. 1
.035 in., .045 in., & 1/16 in.
Size of Filler Metals
Filler Metal Product Form Solid Wire
Supplemental Filler Metal None
Weld Metal
Thickness Range:
3/4 in. Maximum
Groove
All Sizes
Fillet
Electrode-Flux (Class)
Flux Type
Flux Trade Name
Consumable Insert
QW-404.27 Not Applicable QW-404.32 Not Applicable
Other
*Each base metal-filler metal combination should be recorded individually.
(03/08)
PRINT SAVE
QW-482 (Back)
WPS No. WPS-1310 Rev. 0
POSITIONS (QW-405) POSTWELD HEAT TREATMENT (QW-407)

Position(s) of Groove Flat & Horizontal Temperature Range None
Welding Progression: Up Not Applicable Down Time Range
Position(s) of Fillet Flat & Horizontal Other QW-407.4 Not Applicable
Other
GAS (QW-408)
PREHEAT (QW-406) Percent Composition
Preheat Temperature, Minimum 32° F Gas(es) (Mixture) Flow Rate
Interpass Temperature, Maximim None
Preheat Maintenance None Shielding Argon / Oxyge 98 % / 2 % 30 to 40 CF/Hr
Other Trailing None
(Continuous or special heating, where applicable, should be recorded) Backing None
Other QW-408.9 & QW-408.10 Not Applicable
ELECTRICAL CHARACTERISTICS (QW-409)

Direct Current Electrode Positive, (Reverse Polarity)
Filler Metal Other

(e.g., Remarks, Com-
Current Wire Feed Energy or Travel ments, Hot Wire
Weld Classifi- Type and Amps Speed Power Volts Speed Addition, Technique,
Pass(es) Process cation Diameter Polarity (Range) (Range) (Range) (Range) (Range) Torch Angle, etc.)
All GMAW ER70S-6 .035 in. DCEP 150 - 270 23 - 31 2 to 24 ipm
All GMAW ER70S-6 .045 in. DCEP 190 - 310 23 - 31 2 to 24 ipm
All GMAW ER70S-6 1/16 in. DCEP 200 - 340 23 - 33 2 to 24 ipm
Amps and volts, or power or energy range, should be recorded for each electrode size, position, and thickness, etc.
Pulsing Current Heat Input (max.)
Tungsten Electrode Size and Type

(Pure Tungsten, 2% Thoriated, etc.)
Spray Transfer
Mode of Metal Transfer for GMAW (FCAW)
(Spray Arc, Short Circuiting Arc, etc.)
Other
TECHNIQUE (QW-410)
String or Weave Bead Stringer Bead or Weave Bead or Both
Orifice, Nozzle, or Gas Cup Size #6, #8, #10, or #12
Initial and Interpass Cleaning (Brushing, Grinding, etc.) Chemical Cleaning, Grinding, Wire Brushing, Chipping or Combinations
Method of Back Gouging Mechanical or Thermal followed by Mechanical
Oscillation Yes, 3/4 inch width maximum, 0 to 120 cycles per minute maximum
Contact Tube to Work Distance 1/4 in. to 1 in.
Multiple or Single Pass (Per Side) Single or Multiple Pass per Side
Multiple or Single Electrodes Single Electrode
Electrode Spacing Not Applicable
Peening None
Other QW-410.64 Not Applicable
(07/10)
PRINT SAVE

WPS 1310

Uploaded by

WPS 1310

Uploaded by

QW-482 SUGGESTED FORMAT FOR WELDING PROCEDURE SPECIFICATIONS (WPS)

Company Name Small Vessel Works, Inc. By Bill Jones

Welding Process(es) GMAW - Spray Type(s) Automatic, Machine, or Semi-Automatic

JOINTS (QW-402) Details

Backing: Yes With No Without

Backing Material (Type) Metal or Weldmetal, No Retainers

✔ Metal Nonfusing Metal

[At the option of the manufacturer, sketches may be attached to illustrate

*BASE METALS (QW-403)

*FILLER METALS (QW-404) 1 2

AWS No. (Class) ER70S-6

Supplemental Filler Metal None

*Each base metal-filler metal combination should be recorded individually.

POSITIONS (QW-405) POSTWELD HEAT TREATMENT (QW-407)

ELECTRICAL CHARACTERISTICS (QW-409)

Filler Metal Other

All GMAW ER70S-6 .035 in. DCEP 150 - 270 23 - 31 2 to 24 ipm

All GMAW ER70S-6 .045 in. DCEP 190 - 310 23 - 31 2 to 24 ipm

All GMAW ER70S-6 1/16 in. DCEP 200 - 340 23 - 33 2 to 24 ipm

Pulsing Current Heat Input (max.)

Tungsten Electrode Size and Type

Method of Back Gouging Mechanical or Thermal followed by Mechanical

Contact Tube to Work Distance 1/4 in. to 1 in.

Multiple or Single Electrodes Single Electrode

Electrode Spacing Not Applicable

Other QW-410.64 Not Applicable

You might also like