Inroduction

At the time of her construction, the Titanic was the largest ship ever built. She was nearly 900 feet long, stood 25 stories high, and weighed an incredible 46,000 tons [Division, 1997]. With turn-of-the-century design and technology, including sixteen major watertight compartments in her lower section that could easily be sealed off in the event of a punctured hull, the Titanic was deemed an unsinkable ship. According to her builders, even in the worst possible accident at sea, two ships colliding, the Titanic would stay afloat for two to three days, which would provide enough time for nearby ships to help. On April 14, 1912, however, the Titanic sideswiped a massive iceberg and sank in less than three hours. Damaging nearly 300 feet of the ship's hull, the collision allowed water to flood six of her sixteen major watertight compartments. She was on her maiden voyage to the United States, carrying more than 2200 passengers and crew, when she foundered. Only 705 of those aboard the Titanic ever reached their destination. After what seemed like a minor collision with an iceberg, the largest ship ever built sank in a fraction of the time estimated for her worst possible accident at sea.

Location of the accident

According to the Naval Historical Center, on Sunday, the 14th of April, about 10 p.m., Titanic struck an iceberg in latitude 41 46' north, longitude 50 14' west, and sank within about three hours. According to the Gulf of Maine Research Institute, Bob Ballard released the coordinates of the Titanic's location as: The stern section sits on the ocean floor at 41 o43'35" N, 49o56'54" W The boilers are at 41o43'32" N, 49o56'49" W The bow is at 41o43'57" N, 49o56'49" W

History

The Titanic was a White Star Line steamship built in the early nineteen hundreds by Harland and Wolff of Belfast, Ireland. At the time of her construction, she was the largest moving object ever built. With a weight of more than 46,000 tons, a length of nearly 900 feet, and a height of more than 25 stories, she was the largest of three sister ships owned by the White Star Line. The Titanic was also equipped with the ultimate in turn-of-the-century design and technology, including sixteen major watertight compartments in her lower section that could easily be sealed off in the event of a punctured hull. Because of her many safety features and a comment by her designer that she was nearly unsinkable, the Titanic was immediately deemed an unsinkable ship. On April 10, 1912, the Titanic commenced her maiden voyage from Southampton, England, to New York, with 2227 passengers and crew aboard. The passengers included some of the wealthiest and most prestigious people at that time. Captain Edward John Smith, one of the most experienced shipmasters on the Atlantic, was navigating the Titanic. On the night of April 14, although the wireless operators had received several ice warnings from others ships in the area, the Titanic continued to rush through the darkness at nearly full steam. At 11:35 p.m., the lookouts spotted a massive iceberg less than a quarter of a mile off the bow of the ship. Immediately, the engines were thrown into reverse and the rudder turned hard left. Because of the tremendous mass of the ship, slowing and turning took an incredible distance, more than that available. At 11:40, without enough distance to alter her course, the Titanic sideswiped the iceberg, damaging nearly 300 feet of the right side of the hull above and below the waterline.

Cause of the rapid sinking

Material Failures When the Titanic collided with the iceberg, the hull steel and the wrought iron rivets failed because of brittle fracture. A type of catastrophic failure in structural materials, brittle fracture occurs without prior plastic deformation and at extremely high speeds. The causes of brittle fracture include low temperature, high impact loading, and high sulphur content. On the night of the Titanic disaster, each of these three factors was present: The water temperature was below freezing, the Titanic was travelling at a high speed on impact with the iceberg, and the hull steel contained high levels of sulphur. The Hull Steel

The first hint that brittle fracture of the hull steel contributed to the Titanic disaster came following the recovery of a piece of the hull steel from the Titanic wreck. After cleaning the piece of steel, the scientists noted the condition of the edges. Jagged and sharp, the edges of the piece of steel appeared almost shattered, like broken china. Also, the metal showed no evidence bending or deformation. Typical high-quality ship steel is more ductile and deforms rather than breaks. Evidence of the brittle fracture of the hull steel was found when a cigarette-sized coupon of the steel taken from the Titanic wreck was subjected to a Charpy test. When the coupon of the modern steel was tested, the pendulum swung down and halted with a thud; the test piece had bent into a "V." However, when the coupon of the Titanic steel was tested, the pendulum struck the coupon with a sharp "ping," barely slowed, and continued up on its swing; the sample, broken into two pieces, sailed across the room. Pictures of the two coupons following the Charpy test are shown in above figure. What the test showed, and the readout confirmed, is the brittleness of the Titanic's hull steel. When the Titanic struck the iceberg, the hull plates did not deform. They fractured.

The rivets

The wrought iron rivets that fastened the hull plates to the Titanic's main structure also failed because of brittle fracture from the high impact loading of the collision with the iceberg and the low temperature water on the night of the disaster. Figure shows the Titanic during her construction, with the riveted hull plates of her stern visible. With the ship travelling at nearly 25 mph, the contact with the iceberg was probably a series of impacts that caused the rivets to fail either in shear or by elongation. As the iceberg scraped along sections of the Titanic's hull, the rivets were sheared off, which opened up riveted seams. Also, because of the tremendous forces created on impact with the iceberg, the rivet heads in the areas of contact were simply popped off, which caused more seams to open up. Normally, the rivets would have deformed before failing because of their ductility, but with water temperatures below freezing, the rivets had become extremely brittle. When the iceberg tore through the hull plates, huge holes were created that allowed water to flood the hull of the ship. As a result, rivets not in the area of contact with the iceberg were also subjected to incredible forces. Like a giant lever, the hull plates transferred the inward forces, applied to the edges of the cracked plates by the water rushing into the hull, to the rivets along the plate seams. The rivets were then either elongated or snapped in two, which broke the caulking along the seams and provided another inlet for water to flood the ship.

Design Flaws

Along with the material failures, poor design of the watertight compartments in the Titanic's lower section was a factor in the disaster. The lower section of the Titanic was divided into sixteen major watertight compartments that could easily be sealed off if part of the hull was punctured and leaking water. After the collision with the iceberg, the hull portion of six of these sixteen compartments was damaged. Sealing off the compartments was completed immediately after the damage was realized, but as the bow of the ship began to pitch forward from the weight of the water in that area of the ship, the water in some of the compartments began to spill over into adjacent compartments. Although the compartments were called watertight, they were actually only watertight horizontally; their tops were open and the walls extended only a few feet above the waterline. If the transverse bulkheads (the walls of the watertight compartments that are positioned across the width of the ship) had been a few feet taller, the water would have been better contained within the damaged compartments. Consequently, the sinking would have been slowed, possibly allowing enough time for nearby ships to help. However, because of the extensive flooding of the bow compartments and the subsequent flooding of the entire ship, the Titanic was gradually pulled below the waterline. The watertight compartments were useless to countering the damage done by the collision with the iceberg. If there had been no compartments at all, the incoming water would have spread out, and the Titanic would have remained horizontal. Eventually, the ship would have sunk, but she would have remained afloat for another six hours before foundering. This amount of time would have been sufficient for nearby ships to reach the Titanic's location so all of her passengers and crew could have been saved.

The captain

This was Captain E. J. Smith's retirement trip. All he had to do was get to New York in record time. Blame for the incident fell on the ship's deceased captain, E. J. Smith, who was condemned for racing at 22 knots through a known ice field in the dark waters off the coast of Newfoundland. Captain E. J. Smith said years before the Titanic's voyage, "I cannot imagine any condition which would cause a ship to founder. Modern shipbuilding has gone beyond that." Captain Smith ignored seven iceberg warnings from his crew and other ships.

How can we prevent the sinking of Titanic

Watertight section If the number of watertight sections had been increased and -- more importantly -- their heights not reduced as a compromise for the sake of the more opulent upper passenger decks, then the Titanic might not have been sunk by the glancing collision she experienced. Captain orders If the officer in command as the Titanic approached the iceberg (William M. Murdoch) had resisted the natural urge to try to avoid a collision but instead had ordered her into reverse and left her on course for a direct collision, then the Titanic most likely would not have sunk. This is because the glancing blow caused by his attempt to avoid a collision caused the edge of the iceberg to tear into five of the Titanic's watertight sections, one more than the loss of four she was designed to survive. If, instead, she had been allowed to ram the iceberg headon at reducing speed, then the first one or two watertight sections would have been neartotally destroyed, but the remaining intact sections would've meant the ship would've remained afloat.

Sail Even after the titanic hit the iceburg there was a chance that the crew could slow the sinking of the titanic. They could have done this by using a sail. What they could have done is got the sails and draped them over the bow where the hole was and the inrushing water would have party stopped the water coming in. If they had done this there may have been the time to wait for ships to arrive. This way of slowing a ships sinking was used only 3 years before the titanics sinking abord another white star liner the Republic. They used a sail to block the hole and it taken 40 hours for it to sink enough time for 3 ships to arrive.

Effects of the Disaster

In an effort to prevent repeating their mistakes, the White Star Line modified several of their existing ships following the Titanic disaster. The changes were based on the design flaws that were assumed to have contributed to the disaster. Along with these design changes, the White Star Line, and all shipbuilding companies at the time, had newly established safety regulations, agreed upon by both the British and American governments, that they had to follow. Developing safety regulations for ships at sea was another attempt to avoid accidents similar to the Titanic. The following is a discussion of the changes made in the design of ships and the safety regulations implemented as a result of the Titanic disaster. Ship Design Following the Titanic disaster, the White Star Line modified the design of the Titanic's sister ships in two ways: the double bottoms were extended up the sides of the hull and the transverse bulkheads of the watertight compartments were raised. The double bottom on ships is constructed by taking two layers of steel that span the length of the ship and separating them by five feet of space [Garzke and others, 1994]. When a ship runs aground or strikes something in the water, the bottom plate of the hull can be punctured without damage incurred to the top plate. With a double bottom, the chance that a punctured hull would allow water into the watertight compartments is minimized. By extending the double bottoms up the sides of the hull, which adds another layer of steel to the sides of the ship, a similar event can be prevented. If an iceberg, or a collision with another ship, barely punctures the hull, only the space between the inner and outer sidewalls would flood with water. The watertight compartments would remain undamaged. The ends of the transverse bulkheads of the watertight compartments were raised to prevent a tragedy similar to the Titanic. When the hull of the Titanic was torn open in the collision with the iceberg, water began to flood the damaged compartments in the bow. As the ship pitched forward under the weight of the water in the bow compartments, water began to spill over the tops of the bulkheads into adjacent, undamaged compartments. Although called watertight, the watertight compartments were actually only watertight horizontally; their tops were open and the walls extended only a few feet above the waterline. By raising the ends of the transverse bulkheads, if a ship were taking in water through the bow compartments and the ship began to pitch forward, the water in the compartments could not flow over the tops of the bulkheads into the next compartments. As a result, flooding of the damaged compartments could be controlled and isolated to only the damaged sections.

Safety Regulations Along with the changes in ship design that resulted from the Titanic disaster, safety regulations were established to govern passenger ships while at sea. Many of these regulations were established at the 1948 Convention on Safety of Life at Sea. The mandatory use of the wireless, the increased lifeboat capacity, and the implementation of the ice patrol-each of these was developed to prevent accidents similar to the sinking of the Titanic. Wireless is the means of communication for ships at sea. The regulations require that ships exceeding 1600 tons be equipped with wireless apparatus. Use of the wireless is beneficial for ships because they are able to receive weather reports, check their positions, and call for help in emergencies. On the night of the Titanic disaster, several warnings were called in to the Titanic from ships aware of her position. Following her collision with the iceberg, the Titanic was able to send out distress signals to other ships with her position and the status of her damage so help was on the way immediately. Although there was room on deck for twice as many lifeboats, the Titanic carried lifeboats for just over half of the passengers and crew on board. The designer of the Titanic had allowed room on deck for two rows of lifeboats, but one row was removed before the voyage began to make the deck more aesthetically pleasing. With outdated British Board of Trade regulations, the Titanic's twenty lifeboats actually exceeded requirements by 10 percent capacity. The new safety regulations increased the required number of lifeboats to a number that would accommodate all passengers and crew aboard the ship. Based on the length of the ship, a given number of davits, which are the mechanism used to raise and lower the lifeboats, are mounted along the perimeter of the lower deck. Figure 4 shows the davits and lifeboats on the deck of the Titanic. If the minimum lifeboat capacity is not met, additional lifeboats must be stowed under other boats. Regulations also specify that each of the lifeboats must carry oars, sails, a compass, signalling devices, food, and water. In addition, for large ships, two of the boats need to be motor boats. The United States Government began the ice patrol so that ships travelling between England and the United States could be alerted of approaching ice fields. The ice patrol studies and observes the ice conditions in the North Atlantic in order to keep track of where the ice fields are in relation to nearby ships. Ice fields, large expanses of floating ice that are more than five miles in their greatest dimension, shift around depending on weather conditions. Therefore, without the ice patrol, ships would need to constantly monitor the positions of the ice fields. For the Titanic, the ice patrol could have informed the captain of the ice fields and surrounding icebergs and instructed him to stop the ship until morning.

References
Gannon, Robert, "What Really Sank the Titanic," Popular Science, vol. 246, no. 2 (February 1995), pp. 49-55. Garzke, William H., David K. Brown, and Arthur Saniford, "The Structural Failure of the Titanic," Oceans Conference Record (IEEE), vol. 3 (1994), pp. 138-148. Hill, Steve, "The Mystery of the Titanic: A Case of Brittle Fracture?" Materials World, vol. 4, no. 6 (June 1996), pp. 334-335. Manning, George, The Theory and Technique of Ship Design (New York: John Wiley and Sons, Inc., 1956), pp. 25-53. Muckle, William, Modern Naval Architecture (London: W.P. Griffith & Sons, 1951), pp. 121125. Refrigerator, Mister, "R.M.S. Titanic," http://www.scv.net/~fridge/index.htm (May 1998). Rogers, Patrick, Anne-Marie O'Neill, and Sophfronia S. Gregory, "Sunken Dreams," People, vol. 49, no. 10 (March 1998), pp. 44-51. Society of Naval Architects and Marine Engineers, Principles of Naval Architecture, 4th ed. (New York: The Society of Naval Architects and Marine Engineers, 1977), pp. 121-133.