ERHARD Butterfly Valves en
ERHARD Butterfly Valves en
ments according to KTW, DVGW standards W270 or G260). Rising energy costs require optimum flow performance with minimum pressure losses to ensure economic operation. And last but not least, only long life valves and low maintenance costs ensure that the personnel costs necessary for operation are minimised. After all, nowadays, all the costs incurred over the whole life of the valve (life cycle costs) play a decisive role in the choice of product. ... and the solutions from ERHARD The wide range of ERHARD butterfly valves fills these requirements in a particular way. Innovative and customer-focused product development, state of the art engineering, production and assembly technology and continuous quality assurance throughout take place at ERHARD, concentrated in one location for top quality Made in Germany before, during and after installation. This applies for the innovative ERHARD ROCO Premium butterfly valve as well as for the the tried and tested ERHARD EAK butterfly valve.
Thanks to the large range of nominal sizes and pressure ratings as well as the flexible installation and drive options ERHARD ROCO Premium butterfly valves are the perfect solution for many and diverse problems.
Wide range of uses ERHARD butterfly valves are suitable, among other things, for drinking water, non-drinking water, gas and air as well as for wastewater and suspensions. This results in fields of application in drinking water extraction, production and distribution, in water transport, wastewater engineering and gas supply as well as in industry.
1 2 3 4 5 6
No. Advantage
1 2
Property Soft-sealing, butterfly valve, opens with double eccentricity, with securely fixed profile ring Connection of output stem and valve disc through innovative polygonal shaft-hub connection (ROCO Premium) or tried and tested keyed connection (EAK) Valve disc with optimised flow performance High-quality and comprehensive coating concept and perfected design Smooth, easy moving, and in ROCO Premium encapsulated, bearing and sealing part ERHARD slider crank mechanism (SKG) optimally adjusted to the valves characteristic curve Standardised connections for all types of drives: from the handwheel to the electric drive
Optimum sealing performance and easy to open and close, minimum mechanical stress Reliable force transfer without play and with high torque reserves for maximum safety Low pressure loss and high cost-effectiveness Long life of the valve Safe, reliable protection of sensitive media such as drinking water Safe and reliable opening and closing without force peaks for minimised actuating forces Perfect operability in all installation situations
3 4 5 6 7
For many years, ERHARD ROCO butterfly valves, as a logical and consistent development of the tried and tested ERHARD engineering, have provided top quality in nominal sizes from DN 80 to DN 600 and pressure ratings PN 10 and PN 16. This series has been improved still further with a large number of innovative details and is now available as the ERHARD ROCO Premium butterfly valve. Perfect solutions ensure outstanding product properties with respect to operational safety, service life and cost effectiveness and all this on unchanged, attractive terms: shafts encapsulated and therefore not touched by medium polygonal shaft-hub connection between the shaft and valve disc corrosion protection with optimised details optimally coordinated slider crank mechanism
Increasingly difficult operating conditions were an incentive for us to find new and pioneering solutions for the redesign of our ERHARD ROCO butterfly valve. Thanks to our own in-house test centre, we were able to test ROCO Premiums practical usefulness at every stage of the development and compare it with other valves. That gives us as the development team the certainty of being better.
Perfect force and form closure the new polygonal shaft-hub connection Important development steps could not be implemented until the polygonal shaft-hub connection was introduced: fully closed disc eye no additional connecting elements and therefore no separation joints 20 % more torque reserves thanks to the notch-free polygonal profile with the same shaft diameter State of the art, precision production technology enable the connection to be made absolutely free of play and, together with the flow-optimised shape of the valve disc, prevents any fluttering whatsoever. The design is also ideally matched to the reserves of the ERHARD slider crank mechanism used as a standard in the ERHARD ROCO Premium. The new type of design also allows complete encapsulation of the connection between the shaft and valve disc. There is therefore no contact between the shaft and medium and there is no need to select special materials for use with aggressive media. Sealing consistently and logically occurs at coated parts of the component, a decisive plus for protection against corrosion and durability.
The polygonal shaft-hub connection is absolutely free of play, another result of decades of development and production know-how at ERHARD in Heidenheim.
Innovative concept in detail ERHARD ROCO Premium also stands for new ideas when it comes to corrosion prevention and protecting the medium. As a standard feature, the butterfly valve is equipped with ERHARD EKB, a high-quality fusion bonded epoxy coating in accordance with quality assurance RAL-GZ 662 of the GSK Quality Association for Heavy Duty Corrosion Protection of Powder Coated Valves and Fittings (e.g. coating thickness at least 250 m). A diffusion-tight lining made of high-quality ERHARD vitreous enamel is available as an option for the inner part of the valve as well as a fully enamelled version with ERHARD Pro-Enamel. Other coating systems such as epoxy polymer ceramic [page 20] enable tailor-made solutions to customers specific requirements. The innovative new coating concept goes further than ever before and includes, e.g. the sealing surfaces too. Highly modern production technology and exact coating processes enable precisely toleranced and corrosion protected hole diameters. All precisely set O-rings on the output stem seal on the coating [1]. This ensures that unprotected cast iron never comes into contact with the
The corrosion protection with optimised details, achieved through shaft sealing onprecisely coated shaft holes, enables a shaft design with no contact with the media. The clamping ring is completely enclosed in the elastomer sheath and has no contact with the medium. The holes are surrounded by sealing lips and therefore protect the threaded holes against corrosion.
medium. At the same time, the life of the O-rings is therefore increased considerably. Thanks to the design, special shaft materials are not necessary. The bushings made of bearing bronze comply with the Drinking Water Regulations DIN 50930-6. ERHARD ROCO Premium is therefore ideal for the transport of drinking water, but at the same time is also an optimum solution for use with salt water. The fully encapsulated output stem has an anti-blow out design and, together with the closed valve eye without securing elements, also contributes to the corrosion protection. There are no dead spaces with stagnant water. Safe, reliable sealing ERHARD ROCO Premium butterfly valves are equipped with a softsealing main seal. In the EKB version, the sealing ring sits on a rolled up, solid seat ring made of stainless steel and in the enamelled version it sits directly on the smooth vitreous enamel. All ERHARD ROCO Premium valves have a fully rubberised clamping ring as a standard feature, which simultaneously acts as a sealing element. This profiled sealing ring is fixed, media-tight, to the valve disc by means of countersunk head screws, it can be easily readjusted and if necessary can be easily replaced at any time. The setting is permanently secured by means of locking pins.
1 2 1 3
Rubberised profiled sealing ring Enamelled seal Rolled up, solid stainless steel seat ring 1
ERHARD ROCO Premium butterfly valves are available in a fully enamelled version for a perfect protection against corrosion. The special properties of enamel were the reason, why the first pieces of jewellery were already enamelled around 3,500 years ago. And even today, enamel is still indispensable as an engineering material for industrial applications thanks to its special properties. After it has been fired at around 720C, enamel is a vitreous, high-strength material, which forms a durable and permanent bond with the metallic substrate material. One special feature of the ERHARD valves coated in ERHARD Pro-Enamel is the special fibre enamel, where short fibres in the material prevent the enamel cracking in the event of damage. ERHARD Pro-Enamel according to DIN 51178 offers numerous advantages: Safe protection from possible corrosion creep Absolutely impervious to water vapour and oxygen Stable bonding even when material is bent or under other loads High elasticity similar to glass Resistant to acids, alkalis and neutral organic media Extremely resistant to high and low temperatures, can even be used where sudden temperature fluctuations occur Good resistance even to abrasive media thanks to the high hardness of 600 HV No further protective measures necessary even in soil class III Extremely smooth surface (Ra 0.05) ensures perfect hygienic conditions Mineral and organic constituents cannot be deposited on the material, preventing a mineral crust growing which would otherwise reduce the cross-section Ideal countersealing surface for elastomer seals Extremely durable, no embrittlement or chalking High degree of environmental compatibility ERHARD has extensive experience and long years of process know-how for the complex technology of enamelling. A modern enamelling plant enables us to achieve flexible yet high-quality production, since we can seamlessly monitor all the enamelling steps with ERHARD Pro-Enamel from degassing annealing through bright abrasive blasting, the application of slurry to firing and cooling.
2 1 While small cracks can spread in ordinary enamel, the fibres in ERHARD Pro-Enamel immediately stop cracking. The enamel forms a keyed connection with the cast iron and forms a bonding or adhesion zone (2) between the enamel layer (1) and the cast iron as substrate material (3), in which the iron and enamel chemically and physically bond. 3
ERHARD ROCO Premium butterfly valve dismantling type The ideal replacement butterfly valve for use in plants and pipe networks is the ERHARD ROCO Premium butterfly valve dismantling type. All the advantages of the ERHARD ROCO Premium butterfly combined with a high-tensile loose flange produce the perfect valve for all plant and pipe network operators. Butterfly valves with loose flanges have two large fields of application. First they are used as part of a new build project, so that the time and cost consuming installation of dismantling joints can be avoided. On the one hand, new investment savings of around 20 % are possible, depending on the material chosen for the dismantling joints. On the other hand, time for installation and thus labour costs are reduced to about one third.
1
Dismantling type butterfly valves are also ideal when it comes to replacing valves in existing networks systems. Due to the grouting of the flange seal, the valves frequently need to be removed with brute force or special tools. This makes installing a valve of the same type with identical face-to-face dimensions nearly impossible. The ERHARD ROCO Premium butterfly valve dismantling type solves that problem. It is effectively 3 mm shorter than the face-to-face
2
dimension, whereby the flange seal is already integrated in the loose flange concept. This results in a variable face-to-face dimension, which enables this valve to be installed in the existing gap even without a dismantling joint. ERHARD ROCO Premium butterfly valves dismantling type can be used as a shut-off valve in plant or as an underground pipe network valve. By mounting and fixing on the fixed flange side, the valve is installed locked and cannot inadvertently twist itself.
During inspection work, the state water supply of Baden-Wrttemberg replaced a gate valve with a ERHARD ROCO Premium butterfly valve dismantling type [3/4]. Valve replacement is facilitated by pulling up the loose flange spreading the valve flange and pipe flange to enable installation of the seal is no longer necessary. Easy installation is also possible in vertical pipes [5]. No timeconsuming bolstering of the valve during assembly is needed, as the valve is fastened to the fixed flange during installation. The perfect fit of the valve ensures top operability in all installation situations [6]. It is even possible to subsequently turn the valve when it is installed.
The loose flanges are movable within a specific application range (-1 mm + 5 mm). In addition, they are connected to the valve housing with an end-load bearing joint. The face-to-face dimension of a dismantling type butterfly valve is produced in the direction of negative tolerance. Additional clearance results due to the omission of the flange seal on the loose flange side. The seal is integrated in the loose flange. Before installation [1] the loose flange with integrated flange seal is moved to the inner position. The housing has been manufactured with minus tolerance, resulting in a gap between the butterfly valve and the pipe, which facilitates installation in the existing gap. After installation [2] the loose flange with integrated flange seal is pulled towards the pipe flange and the flange connection is bolted. The loose flange thus bridges the gap between the valve and the pipe. The integrated flange seal provides a reliable seal both to the pipe and the valve housing. The fastening elements ensure a tight connection between the loose flange and the valve. ERHARD ROCO Premium butterfly valve BLS The new restrained BLS socket and shaft-end connection (BLS = Buderus Lock System) is the result of further development of tried and tested thrust protection systems. It is keyed and can withstand high loads and stresses, i. e. it can also be used for extreme application cases, and it is easy to install and dismantle. The BLS system has for example proven to be ideally suited in rocky terrain. Due to the numerous technical and economic advantages of this flangeless connection, ERHARD has developed ERHARD ROCO Premium butterfly valves in nominal sizes 200, 250 and 300 (PN 16) as well as other valves and fittings for this forward-looking system.
welding work in pipe trenches. The body of the valve is made of ST52-3. The pressure tests for gas are carried out according to DIN 3230 Part 5 in PG1 or PG3. ERHARD ROCO butterfly valve long series design Apart from the standard design with face-to-face dimensions according to DIN EN 558 basic line 14, ERHARD ROCO butterfly valves are also available with a long design according to basic line 15. The range of products available includes nominal sizes DN 400 to DN 1200 with pressure ratings PN 10 and PN 16; other designs are available on request. A design with and without bypass is available as a possible basic version. The main area in which this valve is used is for the pressure-surge free filling and draining of pipes via the integrated bypass with an ERHARD gate valve. Time-consuming assembly of a bypass pipe in pipe trenches is therefore no longer necessary. The whole system is as if cast from one piece and provides optimum corrosion protection.
The bypass in ERHARD ROCO butterfly valves long series design is equipped with an ERHARD gate valve.
Further accessories The wide range of ERHARD butterfly valves also includes other accessories, e.g. End position switch on gearbox Lockable handwheels Lifting devices For further information, please contact your ERHARD consultant.
10
Areas of use
PN DN Water up to max. 60 C Test pressure in bar according to DIN EN 12266-1 Body Closure Largest allowable working pressure in bar Gas up to max. 60 C Area of use and tests for use in ... Gas pipes according to DIN 2470, Part 1 > Pressure tests according to DIN 3230, Part 5, PG 1 Gas supply systems according to DIN 30 6902, Part 1 > Pressure tests according to DIN 3230, Part 5, PG 3
the most reasonable in Baden-Wrttemberg. ERHARD ROCO butterfly valves and other valves from ERHARD contribute their share too.
11
ERHARD ROCO Premium butterfly valve dismantling type DN 150 200 200 250 250 300 300 350 400 400 500 PN 16 10 16 10 16 10 16 10 10 16 10 L* 210 230 230 250 250 270 270 290 310 310 350 D 285 340 340 400 400 455 455 520 565 580 670 h1 RZ 199 200 199 200 221 221 221 287 293 293 318 h1 HR 222 222 222 222 244 244 244 321 319 321 348 h1 EA 438 438 438 438 460 460 460 528 528 528 553 h2 117 118 117 118 146 146 146 150 150 150 183 b 150 160 160 180 180 200 200 225 250 250 300 e1 155 180 180 203 228 253 252 295 321 320 373 e2 222 246 246 270 303 328 328 392 418 418 480 e3 RZ 285 309 309 333 366 391 391 457 498 498 560 e3 HR 322 346 346 370 403 428 428 517 543 543 655 e3 EA 459 483 483 507 540 565 565 629 655 655 717 e4 85 85 85 85 105 105 105 105 105 105 125 e5 EA 180 180 180 180 160 160 160 160 160 160 140 e6 RZ 185 148 185 148 205 168 205 230 185 230 205 e6 HR 148 185 148 185 168 205 168 185 230 185 300 e6 EA 334 334 334 334 355 354 354 354 354 354 374 d1 RZ 18 18 18 18 18 18 18 22 22 22 22 d2 HR 200 200 200 200 200 200 200 250 250 250 300 G HR 39 51 51 66 76 95 95 175 169 182 244 G RZ 39 51 51 66 76 95 95 175 169 182 244 G EA 61 73 73 89 99 118 118 197 192 205 267 u HR 18 18 18 25 25 25 25 29 29 29 36
ERHARD ROCO Premium butterfly valve BLS DN 200 250 300 D1 296 356 414 D2 222 274 326 B 6 6 6 E1 246 303 328 E2 160 228 253 E4 309 366 391 E5 85 105 105 E6 148 168 168 E7 20,5 20,5 20,5 H2 118 146 146 H3 179 201 201 H4 20 20 20 L 490 550 582 d3 18 18 18 Gearbox SKG 05 1 1 Weight approx. kg 58 80 101
12
Dimensions used: L
d1 h1 D h2 e1 b e2 e3 h2 e1 b e2 D h2 e1 b e2 d2 h1 h1 D
[mm] face-to-face dimension [mm] flange [kg] weight handwheel revolutions (Open/Closed) with round trunnion with handwheel with electric rotary actuator
D G u RZ
e3
e3
HR EA
(dimensions can vary depending on the actuator manufacturer). Other actuator options available on request
D L e4 e6 D L e4 e6 e5 D L e4 e6
Baulaenge Losflanschklappe
ERHARD ROCO Premium butterfly valve dismantling type L* [mm] face-to-face dimension variable from -1 to +5 mm
13
For more than 70 years, ERHARD EAK butterfly valves have provided top-quality tried and tested engineering. Proven details ensure reliable quality and a high degree of cost-effectiveness. With nominal sizes between DN 700 and 3600 and pressure ratings from PN 10 to PN 40, they cover a wide range of applications. Additional customer specific versions are of course always possible. Tried and tested bearing and sealing part The output stem and trunnion are supported in maintenance-free, self-lubricating plain bearings [3]. They are highly resilient, with a robust design for use in the toughest conditions. The DU plain bearings are equipped with a PTFE lining, which ensures a very low coefficient of friction and a correspondingly long life. The double shaft seal [4] is equipped with robust O-rings and support rings and is confined with anti-blow out.
ERHARD EAK butterfly valves are suitable for a wide range of applications: whether in the turbine inlet of the EnBW coal power plant in Karlsruhe [1], where a butterfly valve DN 3600 [2] was installed, or for the comprehensive upgrading of the water supply system in Leipzig [3], parts of which were almost 100 years old. 15 ERHARD butterfly valves size DN 500 to 1000 were installed, some of them with integrated bypass which enables optimum pressure equalisation during starting up.
14
1 3
5 4 10 6 7 11 8 9 12
2 13
Robust key connection For the important connection between the output stem [7] and valve disc [8] for nominal sizes over DN 600, ERHARD uses the tried and tested, robust key connection [6], which ensures force transmission without play even under the highest dynamic stresses and therefore ensures a sufficiently large torque with maximum safety. The key connection is precisely fitted into each valve as a force-closed connection element and connects the shaft and valve disc safely and reliably as if cast from one piece [9]. A special key securing device [5] is also provided as a standard. Safe, reliable sealing ERHARD butterfly valves are soft sealing. The main seal, in the form of a profile ring [11] is clamped onto the valve disc and fixed with a clamping ring [10]. It can easily be adjusted using fixing screws and is easy to replace. It is secured and fixed by means of locking pins. The profile ring with one-piece clamping ring enables uniform and controlled prestressing to be achieved. The profile ring can easily be replaced in the open position. On request, the main seal is also available made of Viton, PU or other special materials. Standard ERHARD butterfly valves are also optionally available with an inner coating made of EKB or vitreous enamelling, whereby the design of the seat ring varies: Rolled in, solid seat ring made of stainless steel is used for the fusion bonded epoxy coating (ERHARD EKB, blue) according to the requirements of DIN 30677 Part 2. If the inner surface is enamelled (ERHARD vitreous enamel, blue), the seat is positioned directly on the enamel. Alternatively, other high-quality coatings are available, such as epoxy ceramic.
Bearing (using the example EAK DN 800 PN 10) 1 Drive side 2 Bearing / blind side 3 Plain bearing 4 Maintenance-free shaft seal Key connection 5 Key securing device 6 Key 7 Output stem 8 Valve disc 9 Force-closed connection and force transmission Seat 10 Clamping ring 11 Profile ring 12 Enamelled seat 13 Rolled in, solid stainless steel seat ring with EKB
15
Shaft seal: elastomer Profiled sealing real: elastomer, confined with clamping ring, EPDM or NBR, optionally Viton Screws: internal and external A2 SKG / SK slider crank mechanism: degree of protection IP68 / IP67 Gearbox body: grey cast iron EN-JL 1040 / EKB Gearbox crank: steel / black-finished Stem nut: special brass Stem: ferritic Cr steel
Handwheel: steel / EKB Gearbox configuration: standard according to Figure 1 Corrosion protection of the body parts: heavy-duty corrosion assurance in accordance with quality assurance DIN 30 677-2 (at least 250 m), ERHARD EKB fusion bonded epoxy coating, optionally with ERHARD vitreous enamelling on the inside, each blue coloured. Other coating options are available (see page 22), please contact us for advice.
Valve discs made of cast stainless steel are the special feature of the butterfly valves for the Cannington Link project in Perth [1]. And in Belgrade ERHARD EAK butterfly valves DN 3000 with electric actuators secure the water supply [2].
Areas of use
PN DN Water up to max. 60 C Test pressure in bar according to DIN EN 12266-1 Body Closure Largest allowable working pressure in bar Gas up to max. 60 C Area of use and tests for use in ... Gas pipes according to DIN 2470, Part 1 > Pressure tests according to DIN 3230, Part 5, PG 1 Gas supply systems according to DIN 30 6902, Part 1 > Pressure tests according to DIN 3230, Part 5, PG 3 17,0 11,0 10,0 25,0 17,6 16,0 37,5 27,5 25,0 60,0 44,0 40,0 10 700-3000 16 700-2600 25 150-1800 40 150-1800
16
Other nominal sizes, pressure ratings and drive options are available on request.
e1
e2 d1 h1 D h2
e1
e2 d2 h1 D h2
e1
e2
h1 D h2
e3
e3 e4
b
e6
e3
Dimensions used L D G u RZ HR EA [mm] face-to-face dimensions [mm] flange [kg] weight handwheel revolutions (Open/Close) with round trunnion with handwheel with electric rotary actuator (dimensions can vary depending on the actuator manufacturer)
e6
e6
e5 L
e5 L
e5 L
17
The valve discs of ERHARD butterfly valves are supported in the body with double eccentricity. As a result, when the swinging opening motion is initiated, a rotational movement [1] is produced which is also superimposed by a transla3
tional movement [2]. The valve rotates, but at the same time it moves away from the seat ring [3]. After a few degrees of opening it therefore lifts off the seat, which safely relieves the sealing ring. All this minimises wear.
Together with complete relaxation of the sealing ring with maximum opening, this results in a far longer life. At the same time, the translational movement
2
ensures that the sealing ring can be easily removed from the seat at any time, even where valves have been closed for many years. Optimised flow performance ERHARD butterfly valves are designed with flow optimisation to ensure minimum effects on the flow when the valve is open. This ensures that the whole system can be operated, e.g. with the lowest possible pump power, which in turn ensures permanently low running costs. The pressure loss to be compensated for can be easily calculated using the above formula and diagram. The table values are based on the averaged flow for the vitreous enamel design. Please contact us if you require headloss coefficients for other nominal sizes and pressure ratings, we will be pleased to help.
Calculation of the pressure loss: p = /2 v2 p v Pressure loss [Pa]-105 Pa ^ 1 bar = Headloss coefficient of the valve [from the diagram] Flow velocity [m/s] Density of water [kg/m3]
10,0 100,0 1000,0
1,0
DN 100 DN 1000
0 10 20 30 40 50 60 70 80 90 100
0,1
Headloss coefficients with fully opened butterfly valve. The results were obtained in ERHARDs test centre following extensive test series and correspond to the actual performance of the fitting.
Headloss coefficients DN 80 100 125 150 200 250 300 350 400 450 PN 10 0,34 0,30 0,27 0,25 PN 16 1,39 0,89 0,57 0,78 0,71 0,42 0,40 0,37 0,34 0,31 DN 500 600 700 800 900 1000 1100 1200 1300 1400 PN 10 0,23 0,20 0,18 0,16 0,15 0,13 0,13 0,12 0,12 0,12 PN 16 0,29 0,26 0,23 0,21 0,19 0,18 0,17 0,16 0,16 0,16 DN 1500 1600 1800 2000 2200 2400 2500 2600 2900 3000 PN 10 0,12 0,12 0,12 0,11 0,11 0,11 0,11 0,11 0,11 0,10 PN 16 0,16 0,15 0,15 0,15 0,15 0,15 0,14 0,14 0,14 0,13
18
Throttling and cavitation Butterfly valves are designed and intended for OPEN-CLOSED operation. Depending on the pressure and velocity conditions, eddy and turbulence zones can result in the intermediate positions, which cause vibrations, oscillations and under certain operating conditions can even cause cavitation and consequently leads to material damage. Cavitation occurs if vapour bubbles form in the pipe. According to Bernoullis law, the total energy of a flowing medium is always the same; the sum of the potential, pressure, velocity (kinetic) and temperature (thermal) energy is constant. If the flow velocity now rises at a construction, e.g. a slightly opened butterfly valve, the pressure energy in the area between the body seat and valve disc simultaneously falls. If the pressure falls below the saturation vapour pressure of the medium, vapour bubbles form. Downstream of the construction the velocity reduces again and the pressure increases, so that the vapour bubbles deform and finally implode. The micro-jet produced during this process hits the wall of the pipe at a high speed and can damage the pipe material.
1 Valve disc 2 1 2
It is therefore advisable to perform suitable cavitation investigations. Our experts will be pleased to perform these calculations for you on the basis of the following data: Plant / system conditions and installation situation Pressure conditions (upstream and downstream pressure) Flow data (minimum, normal, maximum) Special requirements Limit velocities Butterfly valves and their gearboxes are dimensioned so that safe, reliable opening and closing is ensured if a compressive load equal to the nominal pressure PN is applied to the closed valve disc. If water flows through butterfly valves, dynamic torques are produced during the opening and closing of the valve. At high flow velocities, especially if the allocated limit velocities according to DIN EN 1074 is exceeded, it is necessary to check the selected design. If necessary, such operating conditions can be safely controlled by using a higher pressure rating or another suitable valve. Our experts will be pleased to advise you.
19
first shot-blasted with special granulate to make them metallically bright. The coating is then applied with a precisely defined thickness in the electrostatic power station and is fusion bonded at exactly 210 C. The standard coat thickness is at least 250 m, coat thicknesses up to 500 m are possible. The plant operates with state of the art technology and fulfils the test conditions of the GSK Quality Association for Heavy Duty Corrosion Protection of Powder Coated Valves and Fittings with quality assurance RAL-GZ 662. ERHARD EKB is applied to large valves using a wet method and two coats: the electrostatic wet coating with low-solvent 2-component epoxy plastic is applied to a cathodic basic protection (primer). The final wettening to produce heavy-duty corrosion protection
in accordance with DIN 30677-2 takes place in the heat channel. ERHARD EKB is physiologically safe for drinking water and has confirmed test certificates, among others, from the DVGW-Forschungsstelle TZW Karlsruhe, the Hygieneinstitut Gelsenkirchen and the WRAS (WRc) in Great Britain. ERHARD vitreous enamel The inside of the valve and the valve disc are optionally coated with ERHARD vitreous enamel. Optimal protection is offered by the fully enamelled version using ERHARD Pro-Enamel, a special fibre enamel [see page 7]. Special coatings Other special coatings are available for particular requirements, e.g.: EPC coating (epoxy polymer ceramic) with ceramic reinforcing fillers, particularly suitable for abrasive media or seawater ERHARD rubber lining on the inside, also suitable for abrasive media and seawater Individual coloured coatings with PU paints, for example according to the RAL colour scale, as well as with optimum UV protection in outdoor use Explosion protection For valves with ATEX requirements it is necessary to apply a special conductive coating to the external surfaces of the ERHARD EKB-coated valves (powder or wet coat) as a measure to prevent the ignition source from taking effect. When hardened, the black coloured conducting varnish used has an earth leakage resistance according to DIN EN 1081. The valves then fulfil the ATEX directive requirements.
Both finishing with ERHARD EKB [1] and the application of the vitreous enamel [2] are carried out by ERHARD. This ensures optimum quality for long product life.
20
21
is easy to perform. All gearboxes are maintenance-free and encapsulated. They have a position indicator under high-strength inspection glass, which enables easy checking of the valve position. Sliding crank mechanism ERHARD ROCO Premium butterfly valves are delivered with the new developed sliding crank mechanism (SKG), whose movement kinematics have been further optimised and are now virtually exactly the same as the valves characteristic curve. The drive torque is virtually constant over the whole stroke.
Torque
0 10 CLOSED
20
70
80
90 OPEN
22
2 6 3
No. Advantage
1 2
Property Robust, closed body in accordance with degree of protection IP68 Mechanical position indicator, which is directly connected to the shaft; inspection glass made of impact resistant polycarbonate Stable, adjustable limit stop on the stem Shaft-mounted gearbox according to DIN ISO 5211; flange bearing for installation in plant or in the ground or with handwheel or flange according to DIN 5210 for rotary actuator
Long life-cycle and suitable for installation in the ground Check of the opening angle at any time, also with installation in the ground No forces act on parts of the body Flexible actuator options
3 4
5 6
Extremely durable with a high security of investment Extremely soft closing, which minimises the risk of pressure surge a plus point for the safety and service life of all system parts
Use of bronze and stainless steel Decelerated closing speeds near the CLOSED position
23
5 3 4 6 7 8 9
10 11
10
12
13 14
24
16
2 2 5 3 4 3
25
Weight-loaded hydraulic actuator Both ERHARD ROCO Premium and ERHARD EAK butterfly valves are available with an optional hydraulically controlled weight-loaded actuator with a compact design. Its uses include, among other things: Pipe burst protection Combined discharge and nonreturn valve Turbine inlet protecting valve Quick-opening valve All equipment used for hydraulic control of the closed hydraulic system such as pumps and valves are fixed directly to the cylinder with few pipes. To quickly reduce the flow in a pipe, the first damping phase (approx. 70 % of the closing
Weight-loaded hydraulic actuators are available for nominal sizes from DN 200 to 3000. They can be combined with both ERHARD ROCO Premium and with ERHARD EAK butterfly valves.
angle) is run through quickly, the remaining 30 % is highly throttled to keep dynamic pressure peaks low (closing time characteristic 2-stage). The opening process of the butterfly valve takes place with the lifting of the weight-loaded lever by the hydraulic cylinder by means of an electric hydraulic pump or manual oil pump. The valve disc is hydraulically held in the open position. Force piston and emergency handwheel The design with force piston and emergency handwheel ensures that the fitting can be safely closed even if the hydraulics or compressed air supply fails. Return flow prevention For special applications such as manifolds with parallel pumps or riser pipes, butterfly valves from DN 150 can also be combined with suitable checking protection to prevent return flow. ERHARD check valves are produced to the same high standards and with their stable bodies, streamlined valve disc, shafts protruding on both sides and with maintenance-free supports as well as a robust key connection between the shaft and disc, they are the perfect addition for ERHARD ROCO Premium or ERHARD EAK butterfly valves.
The professionals also rely on ERHARD when it comes to butterfly valves for use in major international projects. For example, 26 ERHARD EAK butterfly valves DN 2400 with weight-loaded hydraulic actuators were used in the new power station built in the Chinese Taishan region [1]. The 18 tonne gravity valves in the Australian Warragamba Dam are designed for emergency closure at max. 30 m/s [2]. 1 2
26
Intermediate support
10 15 30 40 55 50 60 70 80 90 110 130
9 41 63 95 120 150 180 210 225 270 295 320 360 385 445 505
ERHARD three-point blocking Inadvertent opening of the butterfly valve during inspections in the pipe system is safely and reliably prevented by ERHARD three-point locking. This ensures the butterfly valve functions as a locked safety valve, closed driptight. The pipe can be safely accessed even if a maloperation occurs at the butterfly valves actuator. The locking device consists of two fixed and one moving limit stop. A bolt actuated with the handwheel moves into the body at the moving limit stop and reliably blocks the closed valve disc. In this position the valve is closed, drip-tight, in both pressure directions.
The bolt positions of the ERHARD three-
Additional mechanical locking of the bolt in the end positions acts as an additional safety feature. Inadvertent opening and closing of the locking device is therefore effectively prevented. The locking device is also dimensioned so that it withstands, at all times, the maximum actuating torque occurring from the valve actuator. Even if the output stem fails, the valve remains securely closed and therefore provides maximum safety. Other blocking device designs available on request.
point locking are optionally queried via limit switches. Corresponding signals can be further processed for visualisation and actuation control.
27
Apart from these two national certificates, ERHARD butterfly valves also have numerous other international approvals. Please contact us if you require further information regarding these.
The Harz waterworks with its more than 500 km long transport network supplies top-quality drinking water to more than 1.5 million people. The naturally soft water is extracted, among other places, from the Granetal Reservoir in the western Harz region. Up to 180,000 m per day of highquality drinking water is extracted from this reservoir with 46 million m drinking water. Since the Harz waterworks started operation in 1928, engineering planning has been focused on the durability of the plant and systems. The waterworks at the Granetal Reservoir was built in 1972 and is currently equipped with ERHARD ROCO Premium butterfly valves.
28
Merely delivering a product is not enough, especially for complex technical installations. And so we at ERHARD are to hand to help you with advice and support in all life cycle phases. Highly qualified teams in our head office in Heidenheim and representatives throughout the whole of Germany and on five continents work together with you to draw up first class solutions. Planning and design Individual advice from our experienced engineers and technicians begins during the project phase. In this way, through dialogue with the customer, optimum solutions are produced, regardless of whether they use series products or require special tailormade designs. These tailor-made packages in particular are the reason why ERHARD products are frequently used for difficult applications and installation situations. Our own test centre is also available for material tests, project-specific investigations as well as for testing and analysing materials and components. Installation and commissioning If necessary, ERHARD employees install the valves in your plant and systems and, together with your employees, put them into service. This naturally also includes training and instructing skilled personnel using detailed operating instructions and training documents. Maintenance and repair ERHARD is available with services to assist you during the long service life of the valve too. Regular inspections and maintenance ensures that the valves reliably function at all times. If problems should occur, repairs can be carried out quickly on site. Spare parts required for this are quickly available, even years after commissioning. In addition, our technicians in the Heidenheim factory are available for major repair work. We also provide these services for other manufacturers brands.
29
30
Hydrants
House connection
31
TALIS is the undisputed Number One for water transport and water flow control. TALIS has the best solutions available in the fields of water and energy management as well as for industrial and communal applications. We have numerous products for comprehensive solutions for the whole water cycle from hydrants, butterfly valves and knife gate valves through to needle valves. Our experience, innovative technology, global expertise and individual consultation processes form the basis for developing longterm solutions for the efficient treatment of the vitally important resource water. ERHARD GmbH & Co. KG Postfach 1280 D-89502 Heidenheim Meeboldstrasse 22 D-89522 Heidenheim Phone: Fax: E-Mail: +49 7321 320-0 +49 7321 320-491 info@erhard.de
Internet: www.erhard.de
Note: Specifications may be changed without notification at any time. Copyright: No copying without express written permission of ERHARD ERHARD is a Registered Trademark. 46182 DE (04/12)