Module 2

Addition/subtraction of signed numbers

xi yi Carry-in ci Sumsi Carry-outci +1
At the ith stage:
0 0 0 0 0 Input:
0 0 1 1 0 ci is the carry-in
0 1 0 1 0
0 1 1 0 1
Output:
1 0 0 1 0 si is the sum
1 0 1 0 1 ci+1 carry-out to (i+1)st
1 1 0 0 1
1 1 1 1 1
state

si = xi yi ci + xi yi ci + xi yi ci + xi yi ci = x i  yi  ci
ci +1 = yi ci + xi ci + xi yi

Example:

X 7 0 1 1 1 Carry-out xi Carry-in
+Y = +6 = + 00 1 1 1 1 0 0 0 yi
ci+1 ci
Z 13 1 1 0 1 si

Legend for stage i

Addition logic for a single stage
Sum Carry
yi
c
i
xi
xi
yi si c
c i +1
i
ci
x
xi yi i
yi

ci + 1 Full adder ci
(FA)

s
i

Full Adder (FA): Symbol for the complete circuit

for a single stage of addition.
n-bit adder
•Cascade n full adder (FA) blocks to form a n-bit adder.
•Carries propagate or ripple through this cascade, n-bit ripple carry adder.

xn - 1 yn - 1 x1 y1 x0 y0

cn - 1 c1
cn FA FA FA c0

sn - 1 s1 s0
Most significant bit Least significant bit
(MSB) position (LSB) position

Carry-in c0 into the LSB position provides a convenient way to

perform subtraction.
K n-bit adder
K n-bit numbers can be added by cascading k n-bit adders.

xkn - 1 ykn - 1 x2n - 1 y2n - 1 xn y n xn - 1 y n - 1 x 0 y 0

cn
n-bit n-bit n-bit c
c kn 0
adder adder adder

s s( s s s s
kn - 1 k - 1) n 2n - 1 n n- 1 0

Each n-bit adder forms a block, so this is cascading of blocks.

Carries ripple or propagate through blocks, Blocked Ripple Carry Adder
n-bit subtractor
•Recall X – Y is equivalent to adding 2’s complement of Y to X.
•2’s complement is equivalent to 1’s complement + 1.
•X – Y = X + Y + 1
•2’s complement of positive and negative numbers is computed similarly.

xn - 1 yn - 1 x1 y1 x0 y0

cn - 1 c1
cn FA FA FA 1

sn - 1 s1 s0
Most significant bit Least significant bit
(MSB) position (LSB) position
n-bit adder/subtractor (contd..)
y y y
n- 1 1 0
Add/Sub
control

x x x
n- 1 1 0

c n-bit adder
n c
0

s s s
n- 1 1 0

•Add/sub control = 0, addition.

•Add/sub control = 1, subtraction.
Detecting overflows
 Overflows can only occur when the sign of the two operands is
the same.
 Overflow occurs if the sign of the result is different from the
sign of the operands.
 Recall that the MSB represents the sign.
 xn-1, yn-1, sn-1 represent the sign of operand x, operand y and result s
respectively.
 Circuit to detect overflow can be implemented by the
following logic expressions:

Overflow  xn1 yn1sn1  xn1 yn1sn1

Overflow  cn  cn1
Computing the add time
x0 y0
Consider 0th stage:
•c1 is available after 2 gate delays.
•s1 is available after 1 gate delay.
c1 FA c0

s0

Sum Carry
yi
c
i
xi
xi
yi si c
c i +1
i
ci
x
i
yi
Computing the add time (contd..)
Cascade of 4 Full Adders, or a 4-bit adder

x0 y0 x0 y0 x0 y0 x0 y0

FA FA FA FA c0
c4 c3 c2 c1

s3 s2 s1 s0

•s0 available after 1 gate delays, c1 available after 2 gate delays.

•s1 available after 3 gate delays, c2 available after 4 gate delays.
•s2 available after 5 gate delays, c3 available after 6 gate delays.
•s3 available after 7 gate delays, c4 available after 8 gate delays.

For an n-bit adder, sn-1 is available after 2n-1 gate delays

cn is available after 2n gate delays.
Fast addition
Recall the equations:

si  xi  yi  ci
ci 1  xi yi  xi ci  yi ci
Second equation can be written as:

ci 1  xi yi  ( xi  yi )ci
We can write:
ci 1  Gi  Pi ci
where Gi  xi yi and Pi  xi  yi

•Gi is called generate function and Pi is called propagate function

•Gi and Pi are computed only from xi and yi and not ci, thus they can
be computed in one gate delay after X and Y are applied to the
inputs of an n-bit adder.
Carry lookahead
ci 1  Gi  Pi ci
ci  Gi 1  Pi 1ci 1
 ci1  Gi  Pi (Gi 1  Pi 1ci 1 )
continuing
 ci1  Gi  Pi (Gi 1  Pi 1 (Gi  2  Pi 2 ci 2 ))
until
ci1  Gi  PiGi 1  Pi Pi1 Gi 2  ..  Pi Pi 1 ..P1G0  Pi Pi 1 ...P0 c 0
•All carries can be obtained 3 gate delays after X, Y and c0 are applied.
-One gate delay for Pi and Gi
-Two gate delays in the AND-OR circuit for ci+1
•All sums can be obtained 1 gate delay after the carries are computed.
•Independent of n, n-bit addition requires only 4 gate delays.
•This is called Carry Lookahead adder.
Multiplication of unsigned numbers

Product of 2 n-bit numbers is at most a 2n-bit number.

Unsigned multiplication can be viewed as addition of shifted
versions of the multiplicand.
 Multiplication of unsigned
numbers (contd..)
 We added the partial products at end.
 Alternative would be to add the partial products at each stage.

 Rules to implement multiplication are:

 If the ith bit of the multiplier is 1, shift the multiplicand and add the
shifted multiplicand to the current value of the partial product.
 Hand over the partial product to the next stage
 Value of the partial product at the start stage is 0.
Multiplication of unsigned numbers
Typical multiplication cell

Bit of incoming partial product (PPi)

jth multiplicand bit

ith multiplier bit ith multiplier bit

carry out FA carry in

Bit of outgoing partial product (PP(i+1))

Combinatorial array multiplierCombinatorial array multiplier

Multiplicand
0 m3 0 m2 0 m1 0 m0
(PP0)
q0
0
PP1 p0
q1
0
PP2 p1
q2
0
PP3 p2
q3
0
,
p7 p6 p5 p4 p3

Product is: p7,p6,..p0

Multiplicand is shifted by displacing it through an array of adders.

Combinatorial array multiplier
(contd..)
 Combinatorial array multipliers are:
 Extremely inefficient.
 Have a high gate count for multiplying numbers of practical size such as 32-
bit or 64-bit numbers.
 Perform only one function, namely, unsigned integer product.

 Improve gate efficiency by using a mixture of

combinatorial array techniques and sequential
techniques requiring less combinational logic.
Sequential multiplication
 Recall the rule for generating partial products:
 If the ith bit of the multiplier is 1, add the appropriately shifted multiplicand
to the current partial product.
 Multiplicand has been shifted left when added to the partial product.

 However, adding a left-shifted multiplicand to an

unshifted partial product is equivalent to adding an
unshifted multiplicand to a right-shifted partial
product.
Sequential Circuit Multiplier
Register A (initially 0)

Shift right

C a a q q
n - 1 0 n - 1 0

Multiplier Q
Add/Noadd
control

n-bit
Adder
MUX Control
sequencer

0 0

m m
n - 1 0

Multiplicand M
Sequential multiplication (contd..)
M
1 1 0 1
Initial configuration
0 0 0 0 0 1 0 1 1
C A Q
0 1 1 0 1 1 0 1 1 Add
Shift First cycle
0 0 1 1 0 1 1 0 1

1 0 0 1 1 1 1 0 1 Add
Shift Second cycle
0 1 0 0 1 1 1 1 0

0 1 0 0 1 1 1 1 0 No add
Shift Third cycle
0 0 1 0 0 1 1 1 1

1 0 0 0 1 1 1 1 1 Add
Shift Fourth cycle
0 1 0 0 0 1 1 1 1

Product
Signed Multiplication
 Considering 2’s-complement signed operands, what will happen to (-
13)(+11) if following the same method of unsigned multiplication?

1 0 0 1 1 ( - 13)
0 1 0 1 1 ( + 11)

1 1 1 1 1 1 0 0 1 1

1 1 1 1 1 0 0 1 1
Sign extension is
shown in blue 0 0 0 0 0 0 0 0

1 1 1 0 0 1 1

0 0 0 0 0 0

1 1 0 1 1 1 0 0 0 1 ( - 143)

Sign extension of negative multiplicand.

Signed Multiplication
 For a negative multiplier, a straightforward solution is
to form the 2’s-complement of both the multiplier and
the multiplicand and proceed as in the case of a
positive multiplier.
 This is possible because complementation of both
operands does not change the value or the sign of the
product.
 A technique that works equally well for both negative
and positive multipliers – Booth algorithm.
Booth Algorithm
 Consider in a multiplication, the multiplier is positive
0011110, how many appropriately shifted versions of
the multiplicand are added in a standard procedure?

0 1 0 1 1 0 1
0 0 +1 +1 + 1+1 0
0 0 0 0 0 0 0
0 1 0 1 1 0 1
0 1 0 1 1 0 1
0 1 0 1 1 0 1
0 1 0 1 1 0 1
0 0 0 0 0 0 0
0 0 0 0 0 0 0
0 0 0 1 0 1 0 1 0 0 0 1 1 0
Booth Algorithm
 Since 0011110 = 0100000 – 0000010, if we use the
expression to the right, what will happen?
0 1 0 1 1 0 1
0 +1 0 0 0 -1 0
0 0 0 0 0 0 0 0 0 0 0 0 0 0
2's complement of
1 1 1 1 1 1 1 0 1 0 0 1 1
the multiplicand
0 0 0 0 0 0 0 0 0 0 0 0
0 0 0 0 0 0 0 0 0 0 0
0 0 0 0 0 0 0 0 0 0
0 0 0 1 0 1 1 0 1
0 0 0 0 0 0 0 0
0 0 0 1 0 1 0 1 0 0 0 1 1 0
Booth Algorithm
Multiplier
Version of multiplicand
selected by biti
Bit i Bit i -1

0 0 0 XM
0 1 +1 XM
1 0 1 XM
1 1 0 XM

Booth multiplier recoding table.

Booth

Algorithm
In general, in the Booth scheme, -1 times the shifted multiplicand is
selected when moving from 0 to 1, and +1 times the shifted
multiplicand is selected when moving from 1 to 0, as the multiplier
is scanned from right to left.
0 0 1 0 1 1 0 0 1 1 1 0 1 0 1 1 0 0

0 +1 -1 +1 0 - 1 0 +1 0 0 - 1 +1 - 1 + 1 0 - 1 0 0

Booth recoding of a multiplier.

Booth Algorithm
0 1 1 0 1 ( + 13) 0 1 1 0 1
X1 1 0 1 0 (- 6) 0 - 1 +1 - 1 0
0 0 0 0 0 0 0 0 0 0
1 1 1 1 1 0 0 1 1
0 0 0 0 1 1 0 1
1 1 1 0 0 1 1
0 0 0 0 0 0
1 1 1 0 1 1 0 0 1 0 ( - 78)

Booth multiplication with a negative multiplier.

Booth Algorithm
 Best case – a long string of 1’s (skipping over 1s)
 Worst case – 0’s and 1’s are alternating
0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1
Worst-case
multiplier
+1 - 1 +1 - 1 +1 - 1 +1 - 1 +1 - 1 +1 - 1 +1 - 1 +1 - 1

1 1 0 0 0 1 0 1 1 0 1 1 1 1 0 0
Ordinary
multiplier
0 -1 0 0 +1 - 1 +1 0 - 1 +1 0 0 0 -1 0 0

0 0 0 0 1 1 1 1 1 0 0 0 0 1 1 1
Good
multiplier
0 0 0 +1 0 0 0 0 -1 0 0 0 +1 0 0 -1
Manual Division
21 10101
13 274 1101 100010010
26 1101
14 10000
13 1101
1 1110
1101
1

Longhand division examples.

Longhand Division Steps
 Position the divisor appropriately with respect to the
dividend and performs a subtraction.
 If the remainder is zero or positive, a quotient bit of 1
is determined, the remainder is extended by another
bit of the dividend, the divisor is repositioned, and
another subtraction is performed.
 If the remainder is negative, a quotient bit of 0 is
determined, the dividend is restored by adding back
the divisor, and the divisor is repositioned for another
subtraction.
Circuit Arrangement
Shift left

an an-1 a0 qn-1 q0
Dividend Q
A Quotient
Setting

N+1 bit Add/Subtract

adder
Control
Sequencer

0 mn-1 m0

Divisor M

Figure 6.21. Circuit arrangement for binary division.

Restoring Division
 Shift A and Q left one binary position
 Subtract M from A, and place the answer back in A
 If the sign of A is 1, set q0 to 0 and add M back to A
(restore A); otherwise, set q0 to 1
 Repeat these steps n times
Examples Initially 0

Shift
0
0
0
0
0
0
0
0
0
1
0
0
1
1
1 0 0 0

0 0 0
Subtract 1 1 1 0 1 First cycle
Set q0 1 1 1 1 0
Restore 1 1
0 0 0 0 1 0 0 0 0
10 Shift 0 0 0 1 0 0 0 0
11 1000 Subtract 1 1 1 0 1
11 Set q0 1 1 1 1 1 Second cycle
Restore 1 1
10 0 0 0 1 0 0 0 0 0
Shift 0 0 1 0 0 0 0 0
Subtract 1 1 1 0 1
Set q0 0 0 0 0 1 Third cycle

Shift 0 0 0 1 0 0 0 0 1
Subtract 1 1 1 0 1 0 0 1
Set q0 1 1 1 1 1 Fourth cycle
Restore 1 1
0 0 0 1 0 0 0 1 0

Remainder Quotient

Figure 6.22. A restoring-division example.

Nonrestoring Division
 Avoid the need for restoring A after an
unsuccessful subtraction.
 Any idea?
 Step 1: (Repeat n times)
 If the sign of A is 0, shift A and Q left one bit position and
subtract M from A; otherwise, shift A and Q left and add M
to A.
 Now, if the sign of A is 0, set q0 to 1; otherwise, set q0 to 0.
 Step2: If the sign of A is 1, add M to A
 Examples Initially

Shift
0
0
0
0
0
0
0
0
0
0
1
0
0
1
1
1 0 0 0

0 0 0 First cycle
Subtract 1 1 1 0 1
Set q0 1 1 1 1 0 0 0 0 0

Shift 1 1 1 0 0 0 0 0
Add 0 0 0 1 1 Second cycle

Set q 1 1 1 1 1 0 0 0 0
0

Shift 1 1 1 1 0 0 0 0
1 1 1 1 1 Add 0 0 0 1 1 Third cycle
Restore
0 0 0 1 1 Set q 0 0 0 0 1 0 0 0 1
remainder 0
Add 0 0 0 1 0
Remainder Shift 0 0 0 1 0 0 0 1
Subtract 1 1 1 0 1 Fourth cycle
Set q 1 1 1 1 1 0 0 1 0
0

Quotient
A nonrestoring-division example.
Fractions
If b is a binary vector, then we have seen that it can be interpreted as
an unsigned integer by:

V(b) = b31.231 + b30.230 + bn-3.229 + .... + b1.21 + b0.20

This vector has an implicit binary point to its immediate right:

b31b30b29....................b1b0. implicit binary point

Suppose if the binary vector is interpreted with the implicit binary point is
just left of the sign bit:
implicit binary point .b31b30b29....................b1b0

The value of b is then given by:

V(b) = b31.2-1 + b30.2-2 + b29.2-3 + .... + b1.2-31 + b0.2-32

Range of fractions
The value of the unsigned binary fraction is:
V(b) = b31.2-1 + b30.2-2 + b29.2-3 + .... + b1.2-31 + b0.2-32

The range of the numbers represented in this format is:

0  V (b)  1  232  0.9999999998

In general for a n-bit binary fraction (a number with an assumed binary

point at the immediate left of the vector), then the range of values is:

0  V (b)  1  2 n
Scientific notation
•Previous representations have a fixed point. Either the point is to the immediate
right or it is to the immediate left. This is called Fixed point representation.
•Fixed point representation suffers from a drawback that the representation can
only represent a finite range (and quite small) range of numbers.

A more convenient representation is the scientific representation, where

the numbers are represented in the form:

x  m1.m2m3m4  b e
Components of these numbers are:

Mantissa (m), implied base (b), and exponent (e)

Significant digits
A number such as the following is said to have 7 significant digits

x  0.m1m2m3m4m5m6m7  b e

Fractions in the range 0.0 to 0.9999999 need about 24 bits of precision

(in binary). For example the binary fraction with 24 1’s:

111111111111111111111111 = 0.9999999404

Not every real number between 0 and 0.9999999404 can be represented

by a 24-bit fractional number.
The smallest non-zero number that can be represented is:

000000000000000000000001 = 5.96046 x 10-8

Every other non-zero number is constructed in increments of this value.

Sign and exponent digits
•In a 32-bit number, suppose we allocate 24 bits to represent a fractional
mantissa.
•Assume that the mantissa is represented in sign and magnitude format,
and we have allocated one bit to represent the sign.
•We allocate 7 bits to represent the exponent, and assume that the
exponent is represented as a 2’s complement integer.
•There are no bits allocated to represent the base, we assume that the
base is implied for now, that is the base is 2.
•Since a 7-bit 2’s complement number can represent values in the range
-64 to 63, the range of numbers that can be represented is:

0.0000001 x 2-64 < = | x | <= 0.9999999 x 263

•In decimal representation this range is:

0.5421 x 10-20 < = | x | <= 9.2237 x 1018

A sample representation
1 7 24

Sign Exponent Fractional mantissa

bit
•24-bit mantissa with an implied binary point to the immediate left
•7-bit exponent in 2’s complement form, and implied base is 2.
Normalization
Consider the number: x = 0.0004056781 x 1012

If the number is to be represented using only 7 significant mantissa digits,

the representation ignoring rounding is: x = 0.0004056 x 1012

If the number is shifted so that as many significant digits are brought into
7 available slots:
x = 0.4056781 x 109 = 0.0004056 x 1012

Exponent of x was decreased by 1 for every left shift of x.

A number which is brought into a form so that all of the available mantissa
digits are optimally used (this is different from all occupied which may
not hold), is called a normalized number.

Same methodology holds in the case of binary mantissas

0001101000(10110) x 28 = 1101000101(10) x 25
Normalization (contd..)
•A floating point number is in normalized form if the most significant
1 in the mantissa is in the most significant bit of the mantissa.
•All normalized floating point numbers in this system will be of the form:

0.1xxxxx.......xx

Range of numbers representable in this system, if every number must be

normalized is:
0.5 x 2-64 <= | x | < 1 x 263
Normalization, overflow and underflow
The procedure for normalizing a floating point number is:
Do (until MSB of mantissa = = 1)
Shift the mantissa left (or right)
Decrement (increment) the exponent by 1
end do

Applying the normalization procedure to: .000111001110....0010 x 2-62

gives: .111001110........ x 2-65

But we cannot represent an exponent of –65, in trying to normalize the

number we have underflowed our representation.
Applying the normalization procedure to: 1.00111000............x 263
gives: 0.100111..............x 264

This overflows the representation.

Changing the implied base
So far we have assumed an implied base of 2, that is our floating point
numbers are of the form:
x = m 2e

If we choose an implied base of 16, then:

x = m 16e

Then:
y = (m.16) .16e-1 (m.24) .16e-1 = m . 16e = x

•Thus, every four left shifts of a binary mantissa results in a decrease of 1

in a base 16 exponent.
•Normalization in this case means shifting the mantissa until there is a 1 in
the first four bits of the mantissa.
Excess notation
•Rather than representing an exponent in 2’s complement form, it turns out to be
more beneficial to represent the exponent in excess notation.
•If 7 bits are allocated to the exponent, exponents can be represented in the range of
-64 to +63, that is:
-64 <= e <= 63
Exponent can also be represented using the following coding called as excess-64:

E’ = Etrue + 64
In general, excess-p coding is represented as:
E’ = Etrue + p

True exponent of -64 is represented as 0

0 is represented as 64
63 is represented as 127

This enables efficient comparison of the relative sizes of two floating point numbers.
IEEE notation
IEEE Floating Point notation is the standard representation in use. There are two
representations:
- Single precision.
- Double precision.
Both have an implied base of 2.
Single precision:
- 32 bits (23-bit mantissa, 8-bit exponent in excess-127 representation)
Double precision:
- 64 bits (52-bit mantissa, 11-bit exponent in excess-1023 representation)
Fractional mantissa, with an implied binary point at immediate left.

Sign Exponent Mantissa

1 8 or 11 23 or 52
Peculiarities of IEEE notation
•Floating point numbers have to be represented in a normalized form to
maximize the use of available mantissa digits.
•In a base-2 representation, this implies that the MSB of the mantissa is
always equal to 1.
•If every number is normalized, then the MSB of the mantissa is always 1.
We can do away without storing the MSB.
•IEEE notation assumes that all numbers are normalized so that the MSB
of the mantissa is a 1 and does not store this bit.
•So the real MSB of a number in the IEEE notation is either a 0 or a 1.
•The values of the numbers represented in the IEEE single precision
notation are of the form:
(+,-) 1.M x 2(E - 127)
•The hidden 1 forms the integer part of the mantissa.
•Note that excess-127 and excess-1023 (not excess-128 or excess-1024) are used
to represent the exponent.
Exponent field
In the IEEE representation, the exponent is in excess-127 (excess-1023)
notation.
The actual exponents represented are:

-126 <= E <= 127 and -1022 <= E <= 1023

not
-127 <= E <= 128 and -1023 <= E <= 1024

This is because the IEEE uses the exponents -127 and 128 (and -1023 and
1024), that is the actual values 0 and 255 to represent special conditions:
- Exact zero
- Infinity
Floating point arithmetic
Addition:
3.1415 x 108 + 1.19 x 106 = 3.1415 x 108 + 0.0119 x 108 = 3.1534 x 108
Multiplication:
3.1415 x 108 x 1.19 x 106 = (3.1415 x 1.19 ) x 10(8+6)

Division:
3.1415 x 108 / 1.19 x 106 = (3.1415 / 1.19 ) x 10(8-6)

Biased exponent problem:

If a true exponent e is represented in excess-p notation, that is as e+p.
Then consider what happens under multiplication:

a. 10(x + p) * b. 10(y + p) = (a.b). 10(x + p + y +p) = (a.b). 10(x +y + 2p)

Representing the result in excess-p notation implies that the exponent

should be x+y+p. Instead it is x+y+2p.
Biases should be handled in floating point arithmetic.
Floating point arithmetic: ADD/SUB
rule
 Choose the number with the smaller exponent.
 Shift its mantissa right until the exponents of both the
numbers are equal.
 Add or subtract the mantissas.
 Determine the sign of the result.
 Normalize the result if necessary and truncate/round
to the number of mantissa bits.

Note: This does not consider the possibility of overflow/underflow.

Floating point arithmetic: MUL rule
 Add the exponents.
 Subtract the bias.
 Multiply the mantissas and determine the sign of the
result.
 Normalize the result (if necessary).
 Truncate/round the mantissa of the result.
Floating point arithmetic: DIV rule
 Subtract the exponents
 Add the bias.
 Divide the mantissas and determine the sign of the
result.
 Normalize the result if necessary.
 Truncate/round the mantissa of the result.

Note: Multiplication and division does not require alignment of the

mantissas the way addition and subtraction does.
Guard bits
While adding two floating point numbers with 24-bit mantissas, we shift
the mantissa of the number with the smaller exponent to the right until
the two exponents are equalized.
This implies that mantissa bits may be lost during the right shift (that is,
bits of precision may be shifted out of the mantissa being shifted).
To prevent this, floating point operations are implemented by keeping
guard bits, that is, extra bits of precision at the least significant end
of the mantissa.
The arithmetic on the mantissas is performed with these extra bits of
precision.
After an arithmetic operation, the guarded mantissas are:
- Normalized (if necessary)
- Converted back by a process called truncation/rounding to a 24-bit
mantissa.
Truncation/rounding
 Straight chopping:
 The guard bits (excess bits of precision) are dropped.

 Von Neumann rounding:

 If the guard bits are all 0, they are dropped.
 However, if any bit of the guard bit is a 1, then the LSB of the retained bit is
set to 1.
 Rounding:
 If there is a 1 in the MSB of the guard bit then a 1 is added to the LSB of the
retained bits.
Rounding
 Rounding is evidently the most accurate truncation
method.
 However,
 Rounding requires an addition operation.
 Rounding may require a renormalization, if the addition operation de-
normalizes the truncated number.

0.111111100000 rounds to 0.111111 + 0.000001

=1.000000 which must be renormalized to 0.100000

 IEEE uses the rounding method.