Hipot Testing 102
• AC vs. DC Testing
• Leakage Current Limits
• 500 VA Hipot Testing
• Fault Detection Systems
• Hipot Tester Features
Meet Our Team
Webinar Notes
Please use the Q & A utility to ask us any questions concerning the material
being presented.
You can find a recording of this webinar and presentation on our Webinar
Archive page, www.arisafety.com/webinars/archived-webinars/
Please contact Brittany Socha – on the chat line or email
[email protected] if you have any connection issues.
Hipot Testing 102: Learning Objectives
AC vs DC Reactive vs. Real
Pros. and Cons.
Testing Current
What is 500VA Line vs. Load
500 VA Hipot Testing Testing? Regulation
Hipot Instrument SmartGFI, Interlock Ramp-Hi and
Features & Prompt and Hold Charge-Lo
Dielectric Withstand or Hipot Test
The Dielectric Voltage-Withstand Test, or Hipot (High
Potential) Test, is designed to stress the insulation of your
product far beyond what it will encounter during normal use.
The Assumption is that if the insulation can withstand the
significantly higher voltage for a given time it will be able to
function adequately at its normal level. Thus, the term
“Voltage Withstand Test”.
AC vs. DC Hipot Testing
AC or DC • Depending on the product being tested and the test standard, the
hipot test can either be performed using AC or DC potential.
• Both AC and DC hipot tests have inherent advantages and
Differences disadvantages which are evident depending on the product being
tested.
• It is important to understand the difference between the nature of
Which to use? AC and DC voltage/current.
AC vs. DC Hipot Testing
Due to the characteristics of your
product it may be beneficial to test
in either AC or DC voltages. Most
standards will allow for either but
with a variation in Voltage.
H.17.1.2 Voltage-limiting-clamping devices (MOV) or line-to-ground filter (capacitors) are may be
removed prior to test, or the test may be conducted using a dc potential at 1.414 times the AC
potential
Ohm’s Law
The behavior of AC and DC current varies in a resistive and capacitive circuit.
AC current is bi-directional in nature whereas DC current flows in one direction.
The relationship between current, voltage and resistance is defined by the famous OHM’s LAW
OHM’s Law governs the relationship between current, voltage and resistance
Poll Question 1
We know a Hipot test can cause breakdown to your products insulation
but can performing a Hipot test on your product cause damage to the
actual Hipot tester?
The DC Hipot Test – Charging Current
In a capacitive circuit, the AC and DC currents behave differently.
When a DC potential is applied across a capacitor, large amount of current is
required to charge the capacitor.
As the capacitor charges up with time, the current decreases and point comes where
the capacitor is fully charged and no current flows.
The AC Hipot Test – Reactive Current
When an AC potential is applied across a resistor, the resulting leakage current is
in phase with the applied voltage.
When an AC potential is applied across a capacitor, the resulting leakage current
that flows is 90° out of phase with the applied voltage.
This is the reactive current due to the capacitor.
AC current through a resistor is bi-directional.
Total Leakage Current
Vector Sum
Relationship
The hipot is more than just a go/no-go test. It can be used to
find various insulation problems.
AC vs. DC
500 VA Hipot Testing
VA Rating - Certain standards require the use of a 500VA hipot transformer
Energy and Breakdown - Originally this was required to ensure hipot voltage output
remained constant under varying line and load conditions
High Leakage Applications - Higher mA output may also be required for high leakage
currents. For example, a 2000m length of cable may have 60mA of leakage.
Most Associated Research instruments have a 5000V output. Thus, the instruments
have a 100mA trip current rating and 200mA short circuit current rating
500 VA Hipot Testing – By the Standards
Line Vs. Load Regulation
If the hipot circuit is too heavily loaded or the input voltage drops, the hipot test voltage can
dip causing an improper hipot test.
Line Vs. Load Regulation
If the hipot circuit is too heavily loaded or the input voltage drops, the hipot test
voltage can dip causing an improper hipot test.
500 VA Hipot Testing
Some standards include exceptions to a 500VA hipot requirement
UL 1598 – Luminaires – Clause 19.20 :
“If the output of the test equipment is less than 500VA, the equipment shall
include a voltmeter in the output circuit to directly indicate test potential.”
Adoption of Exceptions
Keep your eyes open for new versions of standards – many of adding this
exception to the 500VA requirement
In the end, you must follow what the standard states. However, your standard may
contain an exception to the 500VA rule. Make sure you read the standard carefully.
Leakage Current
Leakage current is the stray current that actually flows through the insulation. It is undesired current
that we want to quantify to better understand the quality of an insulation barrier.
Poll Question 2
When Hipot testing do you utilize your Hi and Lo limit parameters?
How to Set Leakage Current Limits?
Perform & Calculate Add Subtract
Record
• Calculate the
average
leakage
current value
for these
products
Say I test 10 DUTs and calculate an average leakage current of 5.5mA. My limits would be:
Hi-Limit → (5.5mA)*0.25 = 1.375mA → 5.5mA + 1.375mA = 6.88mA
Lo-Limit → 5.5mA – 1.375mA = 4.13mA
Hipot Instrument Features
SmartGFI®
Associated Research’s SmartGFI® can detect when an operator is
touching the DUT by monitoring returning leakage current. Standard
units set to 450µA trip. OMNIA ® II series and the new HYPOTULTRA
can be set from 400µA – 5mA.
Interlock
Interlock located across pins 4 & 5 of Signal or Remote Input. Can be wired to
DUT enclosure for an extra means of operator safety.
Prompt and Hold
User set prompt will
hold the sequence
until the operator
presses TEST
The prompt allows the user to set instructions during the sequence. This could be used to convey a
work instruction or for safety purposes.
Ramp HI and Charge-Lo
DC Hipot Test – At test start, there will be inrush current. Once the insulation is charged
(full test potential), the leakage current drops off to near zero mA.
These features are used with a DC hipot or IR test. Due to the nature of a DC withstand
test, setting high and low leakage limits can prove difficult. These features compensate
for this difficulty and allow the user to properly monitor the limits.
Educational Resources
Visit us online to view all of our Educational Resources
arisafety.com/support/educational-resources/
Join Us
Our Next Webinar is
Testing the Ground Circuit
Visit ikonixusa.com/consulting Contact
[email protected] Contact Us
You can find a recording of this webinar and presentation on our
Webinar Archive page, https://www.arisafety.com/webinars/archived-
webinars/
Check out our website for more information arisafety.com
For any questions about our webinars send an email to Brittany at
[email protected]
