Scribd
Upload
182 views2 pages

Delay Using Pic Microcontroller

This document contains code for a microcontroller program that uses timers and input/output ports to flash an LED. It initializes the oscillator, timers, and I/O ports. It uses a timer overflow flag to increment a counter, and flashes the LED when the counter reaches a threshold by toggling an output pin. It also waits for input pin state changes to control the LED behavior.

Uploaded by

Basheer Naderi
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as TXT, PDF, TXT or read online on Scribd
182 views2 pages

Delay Using Pic Microcontroller

This document contains code for a microcontroller program that uses timers and input/output ports to flash an LED. It initializes the oscillator, timers, and I/O ports. It uses a timer overflow flag to increment a counter, and flashes the LED when the counter reaches a threshold by toggling an output pin. It also waits for input pin state changes to control the LED behavior.

Uploaded by

Basheer Naderi
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as TXT, PDF, TXT or read online on Scribd

/*

* File: DLY1.c
*
*/

#pragma config FOSC = HS // Oscillator Selection bits (HS oscillator).


#pragma config WDTE = OFF // Watchdog Timer Enable bit (WDT disabled).
#pragma config PWRTE = ON // Power-up Timer Enable bit (PWRT enabled).
#pragma config BOREN = OFF // Brown-out Reset Enable bit (BOR enabled).
#pragma config LVP = OFF // Low-Voltage (Single-Supply) In-Circuit Serial
Programming Enable bit (RB3 is digital I/O, HV on MCLR must be used for
programming).
#pragma config CPD = OFF // Data EEPROM Memory Code Protection bit (Data
EEPROM code protection off).
#pragma config WRT = OFF // Flash Program Memory Write Enable bits (Write
protection off; all program memory may be written to by EECON control).
#pragma config CP = OFF // Flash Program Memory Code Protection bit (Code
protection off).
#include <xc.h> // Include the header file.

int COUNT = 0; // COUNT is declared as an integer with


value = 0
int DLY = 0; //

void main(void) //
{ //

PORTC = 0; // Clear PORTC bits


TRISC = 0x03; // Makes RC0 and RC1 of PORTC as inputs
PORTD = 0; // Clear PORTD bits
TRISD = 0xFE; // Make RD0 of PORTD as output
ADCON0 = 0x00; // This makes ADCON0 offTe various TMR1
control bits
OPTION_REG = 0x07; // This sets various TMR0 configuration
INTCON , TMR0IE = 1; //
while (1) // This makes the previous steps
executed only once

{ //

DLY: { //
while (!T0IF); // Stays here upto 256 and then T0IF =
1
T0IF = 0; // Resetting the T0IF over flow flag
COUNT ++; // Increments the counter
if (COUNT == 137) // When Count reaches 137, execute the
next instruction //
{ //
COUNT = 0; //
TMR0 = 0; // Timer starts from 0
while (TMR0 < 137); // do nothing while the TMR0 counts up
to 137. Execute the next instruction when it exceeds 137
} //
} //

PORTD, RD0 = 0; //
while (PORTC,RC0 == 0); // Do nothing while RC0 = low and stay
here. Executes the next instruction When RC0 = 1
goto DLY; //
PORTD, RD0 = 1; //
} //
} //

/*
RC1 = 1, RC0 = 0 LED OFF
RC0 = 0, RC1 = 0 LED OFF

RC1 = 1, RC0 = 1 LED Flashes


RC0 = 1, RC1 = 0 LED ON

*
There are two methods of writing program which I have got from an authorized
text book
But both are wrong. The MPLAB XC8 ver.5. will not identify those statements in
brackets.

while (PORTB.0 == 0); // Wait until PORTB.0 becomes 1


while (PORTB.0); // Same instruction as the previous one

The correct usage is:

while(PORTD,RD0 == 0)

*
Also a statement like PORTD,RD0 = 0 is same as (PORTD,RD0 = 0)
Also a statement like while (PORTC == 0x00); denotes the whole bits are zero and
while (PORTC,RC0 == 0) refers a particular bit which is RC0 of PORTC.
Also a statement like PORTD = 0x01; is same as PORTD,RD0 = 0

*/

You might also like